Options, 10% Passive Filter Settings | Liebert 30-130kVA instruction

Operation

Options

This multiple-page screen, accessed from the third page of the SYSTEM SETTINGS screen, enables and disables optional features which might or might not be installed in your UPS. To enable or dis- able one of these options, do the following:

1.Highlight the option you wish to enable or disable.

2.Press UP or DOWN to toggle between enabled or disabled.

3.Press SELECT to set the desired status.

NOTE

Some of the options appearing on the following screens are reserved for future development.

Figure 50 Options screen, page 1

OPTIONS

ACTIVE FILTER				NO
LBS				NO
GENERATOR				NO
AUTO RESTART				NO

N		EXT		EXIT
	NEXT			EXIT

Highlighting 10% PASSIVE OPTIONS and pressing SELECT will bring up the following screen allowing the Operator to decide whether or not the input trap filter should be disconnected at light loads to prevent a leading power factor at the input. For more information, see Input Trap Filter in the options manual.

Figure 51 10% passive filter settings screen

10% PASSIVE FILTER SETTINGS

FILTER DISCONNECT LEVEL	0
FILTER PREFERRED STATE	CLOSED
10% PASSIVE FILTER CONTACTOR	DISABLE
EXIT

43

Image 51

Liebert 30-130kVA manual Options, 10% Passive Filter Settings, Active Filter LBS Generator Auto Restart

Contents

Npower UPS Page Table of Contents Communication Interfaces Maintenance Figures Page Tables Page Important Safety Instructions Overview of Manual System Description Versatility Safety PrecautionsFactory Backup and Service Assistance Reliability Recharge Input Power FailureModes Of Operation Normal Load On UPS Mimic Display CHGSYS. Status Options Operator Controls Battery System General Component DescriptionUPS Module Detailed Component Descriptions Controls HardwareFirmware Operation Input Power FactorBattery Charging Circuit Rectifier/Charger Operation After End-of-discharge Battery DisconnectBattery Charge Current Limiting Battery Equalize Charge Circuit Static Switch Backfeed Protection Nonlinear Load CharacteristicsUnbalanced Load Characteristics Static Bypass Switch Transfer and Retransfer Conditions Operation Operation Navigation Buttons Operator Control Panel Rotary switch Rotary Switch Prev Cancel Save & Exit ConfigurationUser Settings Security Access and Passwords Menu Tree Display Screens and Procedures Secondary Screens Primary Screens Mimic Display Screen Main Menu Screen Dischg FaultsFaults / Alarms Rect SYS. Status Mimic Display Temps DEG C Inlet AIR Outlet AIR Heat Sinks DC BUS / Battery StatusInput Status Freq Freq .9 HZ 213 214 Phase Diff Bypass Input StatusOutput Load Status EXI T Active Faults and AlarmsFaults and Alarms User Shutdown Next System Ratings Manual Startup Second ScenarioAuto Startup Skip Abort Input Modify Current Limit Target and Ramp ValuesModify DC BUS SET Point Target and Ramp Values Serv External maintenance bypass switch, dual-input UPS SIB External Maintenance Bypass External maintenance bypass switch, single-input UPS External Maintenance Bypass Switch Configurations Multiple Battery Cabinets Shutdown User Shutdown Status Reports Status ReportsSystem Status History LOG Clear History Logs Clear Event LOG Event LOG TotalEvent Log Output History LOG02 / 10 OUT-V IN-V Load Freq Input of / UF SBS Line Trap SBS Load Exit Configuration Screens Prev DC BUS VoltsInput Frequency Output Frequency Current Date System SettingsCancel Save & Exit System Settings Time Next PREV. Cancel Save & ExitCurrent Time Order Number Output Transformer Bypass WIND. no Enter PasswordSingle / Dual Input Dual Options 10% Passive Filter SettingsOptions Active Filter LBS Generator Auto Restart Prev Exit Pulse Rectifier Battery GND Fault Green MachineAlternate Power Pole FAN no Line Drop Compensation Communication Options Auto DialNext Exit Auto Dial YES Auto Dial OUT Pager Pager Support ConfigurationPager Enabled Pager Number Pager PIN Modem Health Check PREV. Cancel Next PREV. Cancel 10 % Passive Filter Settings Factory SettingsNext Cancel Freeze Alarm MaskLatching Dial Save & Exit Cancel Alarm / Fault NameAlarm / Fault Name Battery Fuse Fail Alarm / Fault Name F E Auto Dial Customer Alarm Interface Customer Alarm Interface Programmable Output Relay Board #Remote LED Board # Relay Assignments STD SET User DefinedSTD SET UP Down ADD Remove Clear Exit Prog Relay # Manual Transfer Navigating Protocol Battery Test Battery Management Auto Test MIN MAX Weeks Battery CycleBattery Duration Battery Equalizer Stop Start Enabled DisabledAuto Manual Equalize Time Period Battery Temp Compensation ChargeTemperature Battery Temperature Compensation Charge Battery Cycle Monitor Battery Temp Compensation Battery Cycle Monitor Summary Clear BCMClear Summary YES / no Seconds Discharge Cycles SummaryTime Down BATT. EOD Lower SET Point BATT. EOD Upper SET Point Battery Time Low Warning Battery Supplement BATT. Time LOW WarningAuto Restart Auto Restart Trigger Condition Alarm Notifications System Status Monitoring System Status Sign OFF Date 10/30/02 System StatusSign OFF Date 10/30/01 Next Prev Save & Exit Accumulated # of Brown Outs Accumulated Backup HoursAccumulated Operating Hours on UPS Accumulated Operating Hours on Bypass Faults Faults, Alarms, Status Description L Latching...D Dial Alarm / Fault Name F E DelayOn Battery Input Contact #1 UP Down Summary Alarms, functions, and corrective actions Alarm Messages Contact Liebert Global Service to check Excess load from the UPS and attempt to EPO Maximum heat sink temperature limit This is a summary event based on Battery is discharging. This occurs RMS input current has reached Output kVA or kW or RMS current has With the load on UPS, PhaseB output KVA Condition only causes an alarm, but should Push-button switch located on See 3.3.7 Battery Management All of the alarms before attempting to Status Communication Interfaces 1 RS-232 Port Local Reporting Terminal Worldwide ReportingAuto-Dial Dial Out Pager Requesting Information SiteScan Remote Alarm Status Panel Setting Up External Communication Devices Load on BypassOK to Transfer Momentary Overloads Input Power Failure Load on Battery Automatic Re-transfers to UPS Automatic OperationsOverloads Automatic Transfers to Bypass Automatic Module Off Line Maintenance Air Filters Routine MaintenanceBattery Maintenance Record Log Battery Safety Precautions Torque Requirements Battery voltage record Recommended Test Equipment Reporting a ProblemDetecting Trouble Corrective Actions Maintenance 101 Maintenance 102 Page Ne t