Firmware Upgrade *UPG, 11-2 | Moxa Technologies G2150I manual

OnCell G2150I AT Command Set

MOXA Proprietary Commands

Firmware Upgrade: *UPG

Description: This command triggers a X-modem(checksum) downloading session for G2150I firmware image. .

Notes:

•There will always be risks when performing the firmware upgrade. Ensure to have fixed physical connection on both the power and the signal lines, and to have the correct image file.

• System responses with “Clean-up OK All Done!!” message on the terminal if the upgrade is successful.

• X-modem receive timeout: 10 sec.

Example

AT + UPG

Moxa Firmware Upgrader, v1.0

	*UPG:	73851 bytes transferred, in 45s
	Upgrading, please keep power intact and wait for a moment…
	CR
	+WIND:	13
	Restoring modem defaults, please wait…
	OK
	Clean-up OK
	All Done!!
	OK
	+WIND:	13

NOTE	Upgrading the firmware will clear all the settings and reset the OnCell G2150I to its factory
	defaults.

11-2

Page 115

Image 115

Moxa Technologies manual Firmware Upgrade *UPG, OnCell G2150I AT Command Set Moxa Proprietary Commands, 11-2

Contents

Moxa Technical Support G2150I AT Command Set Trademarks OnCell G2150I AT Command Set Table of Contents Chapter Network Service Commands Result Codes, Failure Causes, and Other Tables Chapter V24-V25 Commands Failure Cause from GSM 04.08 Recommendation +CEER Introduction Related Documents Scope of the DocumentEtsi Secretariat Abbreviations OnCell G2150I AT Command SetIntroduction Presentation Rules Definitions AT Command Features Information Response and Result Codes Serial Line SettingsCommand Line OnCell G2150I AT Command Set AT Command Features General Commands Request Model Identification +CGMM OnCell G2150I AT Command Set General CommandsCommand Possible Responses Manufacturer Identification +CGMI Product Serial Number +CGSN Request Revision Identification +CGMRSelect TE Character Set +CSCS Request Imsi +CIMI Phonebook Character Set +WPCSCard Identification +CCID Set Phone Functionality +CFUN Repeat Last Command aPower Off +CPOF Capabilities List +GCAP Phone Activity Status +CPAS ProcedureComplete software reset Command syntax AT+CPAS Clock Management +CCLK Report Mobile Equipment Errors +CMEECommand syntax AT+CKPD=keys Keypad Control +CKPD AT+ CALA? Alarm Management +CALAGeneric SIM Access +CSIM AT+CCLK? A4 Select Terminal Profile C2 Envelope Terminal Response AT+CSIM? AT+CSIM=?C2 Envelope A4 Select Read Binary Read Reco GET Response Status Restricted SIM Access +CRSMDefined values command integer type AT+CRSM? AT+CRSM=? Defined values keyp Defined values Mobile Equipment Control Mode +CMECIndicator Control +CIND Command syntax Multiplexing Mode +CMUX OnCell G2150I AT Command Set General Commands AT+CMUX=? +CME Error errAT+CMUX? Call Control Commands Verbose result code Numeric code Description With Atvo set Dial Command DOnCell G2150I AT Command Set Call Control Commands Command syntax ATDnbI ATDmemindexI ATDmemnameI Used and 10 locations are available Hang-Up Command HNo reply timer fixed at 25 s Command syntax ATHn Answer a Call a Extended Error Report +CEERRemote Disconnection Command syntax Atdl Dtmf Signals +VTD, +VTSCommand syntax AT+VTD=n Command syntax AT+VTS=Tone Automatic Dialing with DTR AT%Dn Command syntax AT%Dn Automatic Answer ATS0 Command syntax ATS0=valueCommand syntax AT+CICB=mode Defined values mode Gain Control +VGR, +VGT Command syntax AT+CSNSCommand syntax AT+VGR=Rgain Single Numbering Scheme +CSNS AT+VGR=val For AT+VGT=val Receive Controller Transmit Gain Network Service Commands Operator Selection +COPS Signal Quality +CSQOnCell G2150I AT Command Set Network Service Commands Error Responses Meaning Network OrangeOrange networks have been detected Calls only Result code Command syntax AT+CREG= modeNetwork Registration +CREG Or 1 is selected Created Operator List Management +WOLM AT+WOPN=? Read Operator Name +WOPNCphs ROM Used for Plmn names AT+WOPN=3,0Memory AT+WOPN=4 Selection of Preferred Plmn List +CPLS Command syntax AT+CPLS= ListEFPLMNsel will be selected Defined values List Preferred Operator List +CPOLPresent and can be selected Can be selected EFPLMNwact present Selected EFPLMNsel present Alphanumeric formatEFPLMNsel present EFPLMNwact present AT+COPN=? Command syntax AT+COPNRead Operator Name +COPN AT+COPN Security Commands Command syntax AT+CPIN=pin OnCell G2150I AT Command Set Security CommandsEnter PIN +CPIN Enter PIN2 +CPIN2 PIN Remaining Attempt Number +CPINC Command syntax AT+CPINC Data calls Facility Lock +CLCKLock, no information on Call barring No longer supported in GSM OnCell G2150I AT Command Set Security Commands Maximum Change Password +CPWDAT+CPWD=? Maximum 4 mini. For call barring, on 4 digits Short Message Commands Parameter Definitions OnCell G2150I AT Command SetShort Message Commands Command syntax in text mode AT+CNMA Select Message Service +CSMSOnCell G2150I AT Command Set Short Message Commands Defined values service SIM memory storage is full GSM 07.05 Phase 2 + versionError in MS Memory capacity exceeded Preferred Message Storage +CPMS AT+CMGF=0 AT+CMGS=14CR Command syntax AT+CMGF=modePreferred Message Format +CMGF AT+CMGF? +CMGF1 AT+CMGF=? Restore Settings +CRES Save Settings +CSASShow Text Mode Parameters +CSDH AT+CSDH=0 AT+CSDH? New Message Indication +CNMIAT+CMTI SM,1 Read Message +CMGR Command syntax AT+CMGR=index Response syntax for text mode Memory at index Command syntax AT+CMGL=stat Response syntax for text modeList Message +CMGL Alphafield Send Message +CMGS Text modeThen have their status changed to REC Read Write Message to Memory +CMGW Format Set Text Mode Parameters +CSMPSend Message From Storage +CMSS Destination number AT+CMGD=3 Delete Message +CMGDVP value Validity period value AT+CMGR=3 Deleted Service Center Address +CSCACommand syntax AT+CSCA=sca Location 1 is deleted Select Cell Broadcast Message Types +CSCB Command syntax AT+WCBM=midsCell Broadcast Message Identifiers +WCBM Message Overwriting +WMGO PDU Mode Text ModeCommand syntax AT+WMGO=loc Message Status Modification +WMSC Was reinitialized Un-change SMS Status +WUSS Copy Messages +WMCP Writing and ME for storing SIM to the FlashSIM is the total memory available in SIM SMS Flash More Messages to Send +CMMS Defined values mode Copy modeCommand syntax AT+CMMS = mode Defined values mode 0 Disable feature Data Commands Defined values speed Using AT Commands During a Data ConnectionOnCell G2150I AT Command Set Data Commands Bearer Type Selection +CBST Command syntax AT+FCLASS= n Select Mode +FCLASSService Reporting Control +CR OnCell G2150I AT Command SetData Commands DTE-DCE Local Rate Reporting +ILRR Command syntax AT+CR=modeCommand syntax AT+CRC=mode Cellular Result Codes +CRC AT+ILRR=0 AT+ILRR=1 AT+ILRR? Radio Link Protocol Parameters +CRLPAT+ILRR=? AT+DS=? Select Data Compression %CV42 bis Data Compression +DS AT%C0 AT%C2 AT%C? Command syntax AT+DR=status Select Data Error Correcting Mode \NV42 bis Data Compression Report +DR V24-V25 Commands Auto-detectable baud rates including 0. The second set OnCell G2150I AT Command Set V24-V25 CommandsFixed DTE Rate +IPR Recommendation the first set of values indicates the range DTE-DCE Local Flow Control +IFCR DTE-DCE Character Framing +ICFDefined values format Command syntax AT&Dn Set DCD Signal &CSet DTR Signal &D Command syntax AT&Cn Back to Online Mode O Set DSR Signal &SResult Code Suppression Q Information responses Default Configuration ZSave Configuration &W DCE Response Format Auto-tests &T OnCell G2150I AT Command SetV24-V25 CommandsCommand syntax AT&Tn Command syntax ATEn Cancellation Restore Factory Settings &FDisplay Configuration &V Command syntax AT&Fn Request Identification Command syntax ATInIdentifications AT+WMUX=1 Data / Commands Multiplexing +WMUXAT+WMUX=? AT+WMUX? Gprs Commands Define PDP Context + Cgdcont OnCell G2150I AT Command Set Gprs Commands10-2 AT+CGQREQ? Quality of Service Profile Requested +CGQREQ10-3 10-4 AT+CGQREQ=? 10-5 GMM/SM 10-6 Quality of Service Profile Minimum acceptable +CGQMIN 10-7 Gprs Attach or Detach +CGATT 10-8 PDP Context Activate or Deactivate +CGACT Gprs Mobile Station Class +CGCLASS Enter Data State +CGDATA10-9 10-10 Select Service for MO SMS Messages +CGSMSAT+CGCLASS=? +CGCLASS CG,CC AT+CGCLASS? +CGCLASS CC Example about automatic attachment see remark above 10-11 Gprs Event Reporting +CGEREP Gprs Network Registration Status +CGREG OnCell G2150I AT Command SetGPRS Commands10-12 Example Request Gprs IP Service ‘D’10-13 10-14 Network Requested PDP Context Activation +CGAUTO=? +CGAUTO?10-15 10-16 +CGANS=? +CGPADDR=? Show PDP Address +CGPADDR10-17 Form GSM recommendation 04.08 or specific. Call Command syntax AT+CR10-18 Context Gprs Parameter Customization + Wgprs10-19 10-20 Activation of an IP PDP context Example Full AT Gprs Command Examples10-21 10-22 Network request Moxa Proprietary Commands OnCell G2150I AT Command Set Moxa Proprietary Commands Firmware Upgrade *UPG11-2 OnCell G2150I AT Command SetMOXA Proprietary Commands Restore Default Setting *DEFAULT11-3 AT*USERPIN=0 AT*USEPIN? Automatic PIN Entry *USEPIN11-4 11-5 Initial Strings *BOOTSTRCommand syntax AT*BOOTSTR=m AT*BOOTSTR=1 AT*BOOTSTR=0 11-6 Serial Port Configuration *SERIALAT*SERIAL? AT*SERIAL=? 11-7 SMS Tunnel Mode *SMS 11-8 AT*SMSTUN=1 Smsout Result Codes, Failure Causes, and Other Tables Error Meaning Resulting from the following commands ME Error Result Code +CME Error error Specific Error Result Codes Message Service Failure Result Code +CMS Error erMeaning Resulting from the following commands Failure Cause from GSM 04.08 Recommendation +CEER Cause Value Diagnostic Facility rejected GSM 04.11 Annex E-2 Mobile Originating SM-Transfer Specific Failure Cause for +CEER Cause No Congestion Verbose Result Code Numeric V0 set Description Unsolicited Result CodesPDU SMS +CIEV Final Result CodesVerbose Result Code Numeric Description Set Verbose Result Code Numeric V0 set Description Intermediate Result Codes

Moxa Technologies G2150I manual Firmware Upgrade *UPG, 11-2

Models: G2150I