Message Status Modification +WMSC | Moxa Technologies G2150I

OnCell G2150I AT Command Set		Short Message Commands

	AT+WCBM=“10,100,1000,10000”	OK
	Note: Write 4 message identifiers in EF- CBMI	Note: CBMIs are stored in EF-CBMI
	AT+WCBM?	+WCBM=“10,100,1000,100000” OK
	Note: Read the CBMIs in EF-CBMI	Note: 4 CBMIs are stored in EF-CBMI

Message Status Modification: +WMSC

Description: These commands allow the manipulation of message status. The accepted status changes are from READ to NOT READ and vice versa, and from SENT to NOT SENT and vice versa.

Command syntax:	AT+WMSC=<loc>,<status>

Command		Possible responses
AT+CMGR=2		+CMGR: “REC READ”,”+336290918”,,”99/05/01
		14:19:44+04” <CR><LF>
		Hello All of you !
		OK
AT+WMSC=2,”REC UNREAD”
AT+CMGR=2		+CMGR: “REC UNREAD”,”+336290918”,,”99/05/01
		14:19:44+04” <CR><LF>
		Hello All of you !
		OK
Possible responses:
OK	if the location is valid

+CMS ERROR: 321 if <loc> is invalid or free

+CMS ERROR: 302 if the new <status> and the previous one are incompatible (1) Note: If all the parameters are correct, the product overwrites the whole SMS in SIM. Only the first byte (Status byte) is changed.

Defined values:

<loc> location number of the stored message (integer) <status> new status to be stored, as for +CMGL command:

PDU Mode

0

1

2

Text Mode

“REC UNREAD”

“REC READ”

“STO UNSENT”

Message Overwriting: +WMGO

Description: The +WMGO command is used to specify a location in the SIM or Flash memory, for the next SMS storing with +CMGW command. The defined location is used only once: +WMGO has to be used again to perform another overwrite.

Important notes:

yIf the external application specifies a free location, and an incoming message is received before the AT+CMGW command occurs, the product may store the incoming message at the specified available location. If the user then issues an AT+CMGW command without changing the location with another AT+WMGO, the received message will be overwritten.

yThe location number is not kept over a software reset.

Command syntax: AT+WMGO=<loc>

7-17

Image 70

Moxa Technologies G2150I manual Message Status Modification +WMSC, Message Overwriting +WMGO, Possible responses

Contents

G2150I AT Command Set Moxa Technical Support OnCell G2150I AT Command Set Trademarks Table of Contents Chapter Network Service Commands Chapter V24-V25 Commands Result Codes, Failure Causes, and Other Tables Failure Cause from GSM 04.08 Recommendation +CEER Introduction Related Documents Scope of the DocumentEtsi Secretariat OnCell G2150I AT Command SetIntroduction Abbreviations Definitions Presentation Rules AT Command Features OnCell G2150I AT Command Set AT Command Features Serial Line SettingsCommand Line Information Response and Result Codes General Commands Manufacturer Identification +CGMI OnCell G2150I AT Command Set General CommandsCommand Possible Responses Request Model Identification +CGMM Product Serial Number +CGSN Request Revision Identification +CGMRSelect TE Character Set +CSCS Request Imsi +CIMI Phonebook Character Set +WPCSCard Identification +CCID Capabilities List +GCAP Repeat Last Command aPower Off +CPOF Set Phone Functionality +CFUN Command syntax AT+CPAS ProcedureComplete software reset Phone Activity Status +CPAS Keypad Control +CKPD Report Mobile Equipment Errors +CMEECommand syntax AT+CKPD=keys Clock Management +CCLK AT+CCLK? Alarm Management +CALAGeneric SIM Access +CSIM AT+ CALA? A4 Select AT+CSIM? AT+CSIM=?C2 Envelope A4 Select Terminal Profile C2 Envelope Terminal Response AT+CRSM? AT+CRSM=? Restricted SIM Access +CRSMDefined values command integer type Read Binary Read Reco GET Response Status Command syntax Mobile Equipment Control Mode +CMECIndicator Control +CIND Defined values keyp Defined values Multiplexing Mode +CMUX OnCell G2150I AT Command Set General Commands AT+CMUX=? +CME Error errAT+CMUX? Call Control Commands Command syntax ATDnbI ATDmemindexI ATDmemnameI Dial Command DOnCell G2150I AT Command Set Call Control Commands Verbose result code Numeric code Description With Atvo set Command syntax ATHn Hang-Up Command HNo reply timer fixed at 25 s Used and 10 locations are available Answer a Call a Extended Error Report +CEERRemote Disconnection Command syntax AT+VTS=Tone Dtmf Signals +VTD, +VTSCommand syntax AT+VTD=n Command syntax Atdl Command syntax AT%Dn Automatic Dialing with DTR AT%Dn Defined values mode Command syntax ATS0=valueCommand syntax AT+CICB=mode Automatic Answer ATS0 Single Numbering Scheme +CSNS Command syntax AT+CSNSCommand syntax AT+VGR=Rgain Gain Control +VGR, +VGT AT+VGR=val For AT+VGT=val Receive Controller Transmit Gain Network Service Commands Error Responses Meaning Signal Quality +CSQOnCell G2150I AT Command Set Network Service Commands Operator Selection +COPS Calls only OrangeOrange networks have been detected Network Or 1 is selected Command syntax AT+CREG= modeNetwork Registration +CREG Result code Operator List Management +WOLM Created ROM Read Operator Name +WOPNCphs AT+WOPN=? AT+WOPN=4 AT+WOPN=3,0Memory Used for Plmn names Selection of Preferred Plmn List +CPLS Command syntax AT+CPLS= ListEFPLMNsel will be selected Can be selected Preferred Operator List +CPOLPresent and can be selected Defined values List EFPLMNwact present EFPLMNsel present Alphanumeric formatEFPLMNsel present EFPLMNwact present Selected AT+COPN Command syntax AT+COPNRead Operator Name +COPN AT+COPN=? Security Commands Command syntax AT+CPIN=pin OnCell G2150I AT Command Set Security CommandsEnter PIN +CPIN Enter PIN2 +CPIN2 Command syntax AT+CPINC PIN Remaining Attempt Number +CPINC No longer supported in GSM Facility Lock +CLCKLock, no information on Call barring Data calls OnCell G2150I AT Command Set Security Commands Maximum 4 mini. For call barring, on 4 digits Change Password +CPWDAT+CPWD=? Maximum Short Message Commands OnCell G2150I AT Command SetShort Message Commands Parameter Definitions Defined values service Select Message Service +CSMSOnCell G2150I AT Command Set Short Message Commands Command syntax in text mode AT+CNMA Memory capacity exceeded GSM 07.05 Phase 2 + versionError in MS SIM memory storage is full Preferred Message Storage +CPMS AT+CMGF? +CMGF1 AT+CMGF=? Command syntax AT+CMGF=modePreferred Message Format +CMGF AT+CMGF=0 AT+CMGS=14CR Restore Settings +CRES Save Settings +CSASShow Text Mode Parameters +CSDH AT+CSDH=0 AT+CSDH? New Message Indication +CNMIAT+CMTI SM,1 Command syntax AT+CMGR=index Response syntax for text mode Read Message +CMGR Alphafield Command syntax AT+CMGL=stat Response syntax for text modeList Message +CMGL Memory at index Send Message +CMGS Text modeThen have their status changed to REC Read Write Message to Memory +CMGW Destination number Set Text Mode Parameters +CSMPSend Message From Storage +CMSS Format AT+CMGR=3 Delete Message +CMGDVP value Validity period value AT+CMGD=3 Location 1 is deleted Service Center Address +CSCACommand syntax AT+CSCA=sca Deleted Select Cell Broadcast Message Types +CSCB Command syntax AT+WCBM=midsCell Broadcast Message Identifiers +WCBM Message Status Modification +WMSC PDU Mode Text ModeCommand syntax AT+WMGO=loc Message Overwriting +WMGO Un-change SMS Status +WUSS Was reinitialized Copy Messages +WMCP Flash SIM to the FlashSIM is the total memory available in SIM SMS Writing and ME for storing Defined values mode 0 Disable feature Defined values mode Copy modeCommand syntax AT+CMMS = mode More Messages to Send +CMMS Data Commands Bearer Type Selection +CBST Using AT Commands During a Data ConnectionOnCell G2150I AT Command Set Data Commands Defined values speed OnCell G2150I AT Command SetData Commands Select Mode +FCLASSService Reporting Control +CR Command syntax AT+FCLASS= n Cellular Result Codes +CRC Command syntax AT+CR=modeCommand syntax AT+CRC=mode DTE-DCE Local Rate Reporting +ILRR AT+ILRR=0 AT+ILRR=1 AT+ILRR? Radio Link Protocol Parameters +CRLPAT+ILRR=? AT%C0 AT%C2 AT%C? Select Data Compression %CV42 bis Data Compression +DS AT+DS=? Command syntax AT+DR=status Select Data Error Correcting Mode \NV42 bis Data Compression Report +DR V24-V25 Commands Recommendation the first set of values indicates the range OnCell G2150I AT Command Set V24-V25 CommandsFixed DTE Rate +IPR Auto-detectable baud rates including 0. The second set DTE-DCE Local Flow Control +IFCR DTE-DCE Character Framing +ICFDefined values format Command syntax AT&Cn Set DCD Signal &CSet DTR Signal &D Command syntax AT&Dn Back to Online Mode O Set DSR Signal &SResult Code Suppression Q DCE Response Format Default Configuration ZSave Configuration &W Information responses Command syntax ATEn OnCell G2150I AT Command SetV24-V25 CommandsCommand syntax AT&Tn Auto-tests &T Command syntax AT&Fn Restore Factory Settings &FDisplay Configuration &V Cancellation Request Identification Command syntax ATInIdentifications AT+WMUX? Data / Commands Multiplexing +WMUXAT+WMUX=? AT+WMUX=1 Gprs Commands Define PDP Context + Cgdcont OnCell G2150I AT Command Set Gprs Commands10-2 AT+CGQREQ? Quality of Service Profile Requested +CGQREQ10-3 AT+CGQREQ=? 10-4 GMM/SM 10-5 Quality of Service Profile Minimum acceptable +CGQMIN 10-6 Gprs Attach or Detach +CGATT 10-7 PDP Context Activate or Deactivate +CGACT 10-8 Gprs Mobile Station Class +CGCLASS Enter Data State +CGDATA10-9 Example about automatic attachment see remark above Select Service for MO SMS Messages +CGSMSAT+CGCLASS=? +CGCLASS CG,CC AT+CGCLASS? +CGCLASS CC 10-10 Gprs Event Reporting +CGEREP 10-11 Gprs Network Registration Status +CGREG OnCell G2150I AT Command SetGPRS Commands10-12 Example Request Gprs IP Service ‘D’10-13 Network Requested PDP Context Activation 10-14 +CGAUTO=? +CGAUTO?10-15 +CGANS=? 10-16 +CGPADDR=? Show PDP Address +CGPADDR10-17 Form GSM recommendation 04.08 or specific. Call Command syntax AT+CR10-18 Context Gprs Parameter Customization + Wgprs10-19 10-20 Activation of an IP PDP context Example Full AT Gprs Command Examples10-21 Network request 10-22 Moxa Proprietary Commands OnCell G2150I AT Command Set Moxa Proprietary Commands Firmware Upgrade *UPG11-2 OnCell G2150I AT Command SetMOXA Proprietary Commands Restore Default Setting *DEFAULT11-3 AT*USERPIN=0 AT*USEPIN? Automatic PIN Entry *USEPIN11-4 AT*BOOTSTR=1 AT*BOOTSTR=0 Initial Strings *BOOTSTRCommand syntax AT*BOOTSTR=m 11-5 AT*SERIAL=? Serial Port Configuration *SERIALAT*SERIAL? 11-6 SMS Tunnel Mode *SMS 11-7 AT*SMSTUN=1 Smsout 11-8 Result Codes, Failure Causes, and Other Tables ME Error Result Code +CME Error error Error Meaning Resulting from the following commands Specific Error Result Codes Message Service Failure Result Code +CMS Error erMeaning Resulting from the following commands Cause Value Diagnostic Failure Cause from GSM 04.08 Recommendation +CEER Facility rejected Specific Failure Cause for +CEER GSM 04.11 Annex E-2 Mobile Originating SM-Transfer Cause No Congestion Verbose Result Code Numeric V0 set Description Unsolicited Result CodesPDU SMS +CIEV Final Result CodesVerbose Result Code Numeric Description Set Intermediate Result Codes Verbose Result Code Numeric V0 set Description