Select Message Service +CSMS | Moxa Technologies G2150I instruction

OnCell G2150I AT Command Set

Short Message Commands

Select Message Service: +CSMS

Description: The supported services are originated (SMS-MO) and terminated short message (SMS-MT) + Cell Broadcast Message (SMS-CB) services.

Command syntax: AT+CSMS=<service>

Command	Possible responses
AT+CSMS=0	+CSMS: 1,1,1
Note: SMS AT command Phase 2 version	OK
Note: SMS AT command Phase 2 version	Note: SMS-MO, SMS-MT and SMS-CB supported
4.7.0
AT+CSMS=1	+CSMS: 1,1,1
Note: SMS AT command Phase 2 +	Note: SMS-MO, SMS-MT and SMS-CB supported
AT+CSMS?	+CSMS: 0,1,1,1
Note: Current values ?	OK
	Note: GSM 03.40 and 03.41 (SMS AT command
	Phase 2 version 4.7.0
AT+CSMS=?	+CSMS: (0,1)
Note: Possible services	OK

Defined values: <service>

0:SMS AT commands are compatible with GSM 07.05 Phase 2 version 4.7.0.

1:SMS AT commands are compatible with GSM 07.05 Phase 2 + version.

New Message Acknowledgement: +CNMA

Description: This command allows reception of a new message routed directly to the TE to be acknowledged.

•In TEXT mode, only positive acknowledgement to the network (RP-ACK) is possible.

•In PDU mode, either positive (RP-ACK) or negative (RP-ERROR) acknowledgement to the network is possible.

Acknowledge with +CNMA is possible only if the +CSMS parameter is set to 1 (+CSMS=1) when a +CMT or +CDS indication is shown (see +CNMI command). If no acknowledgement is given within the network timeout, an RP-ERROR is sent to the network, the <mt> and <ds> parameters of the +CNMI command are then reset to zero (do not show new message indication).

Command syntax in text mode: AT+CNMA

Command syntax in PDU mode: AT+CNMA [ = <n> [ , <length> [ <CR> PDU is entered <ctrl-Z / ESC> ] ] ]

Note: PDU is entered using <ackpdu> format instead of <pdu> format (e.g.. SMSC address field is not present).

Example of acknowledgement of a new message in TEXT mode

Command	Possible responses
AT+CSMS=1	OK
Note: SMS AT commands compatible
with GSM 07.05
Phase 2 + version
AT+CMGF=1	OK
Note: Set TEXT mode	Note: TEXT mode valid

7-3

Image 56

Moxa Technologies G2150I manual Select Message Service +CSMS, New Message Acknowledgement +CNMA, Defined values service

Contents

G2150I AT Command Set Moxa Technical Support OnCell G2150I AT Command Set Trademarks Table of Contents Chapter Network Service Commands Chapter V24-V25 Commands Result Codes, Failure Causes, and Other Tables Failure Cause from GSM 04.08 Recommendation +CEER Introduction Etsi Secretariat Scope of the DocumentRelated Documents OnCell G2150I AT Command SetIntroduction Abbreviations Definitions Presentation Rules AT Command Features Serial Line Settings Command LineOnCell G2150I AT Command Set AT Command Features Information Response and Result Codes General Commands OnCell G2150I AT Command Set General Commands Command Possible ResponsesManufacturer Identification +CGMI Request Model Identification +CGMM Select TE Character Set +CSCS Request Revision Identification +CGMRProduct Serial Number +CGSN Card Identification +CCID Phonebook Character Set +WPCSRequest Imsi +CIMI Repeat Last Command a Power Off +CPOFCapabilities List +GCAP Set Phone Functionality +CFUN Procedure Complete software resetCommand syntax AT+CPAS Phone Activity Status +CPAS Report Mobile Equipment Errors +CMEE Command syntax AT+CKPD=keysKeypad Control +CKPD Clock Management +CCLK Alarm Management +CALA Generic SIM Access +CSIMAT+CCLK? AT+ CALA? AT+CSIM? AT+CSIM=? C2 EnvelopeA4 Select A4 Select Terminal Profile C2 Envelope Terminal Response Restricted SIM Access +CRSM Defined values command integer typeAT+CRSM? AT+CRSM=? Read Binary Read Reco GET Response Status Mobile Equipment Control Mode +CMEC Indicator Control +CINDCommand syntax Defined values keyp Defined values Multiplexing Mode +CMUX OnCell G2150I AT Command Set General Commands AT+CMUX? +CME Error errAT+CMUX=? Call Control Commands Dial Command D OnCell G2150I AT Command Set Call Control CommandsCommand syntax ATDnbI ATDmemindexI ATDmemnameI Verbose result code Numeric code Description With Atvo set Hang-Up Command H No reply timer fixed at 25 sCommand syntax ATHn Used and 10 locations are available Remote Disconnection Extended Error Report +CEERAnswer a Call a Dtmf Signals +VTD, +VTS Command syntax AT+VTD=nCommand syntax AT+VTS=Tone Command syntax Atdl Command syntax AT%Dn Automatic Dialing with DTR AT%Dn Command syntax ATS0=value Command syntax AT+CICB=modeDefined values mode Automatic Answer ATS0 Command syntax AT+CSNS Command syntax AT+VGR=RgainSingle Numbering Scheme +CSNS Gain Control +VGR, +VGT AT+VGR=val For AT+VGT=val Receive Controller Transmit Gain Network Service Commands Signal Quality +CSQ OnCell G2150I AT Command Set Network Service CommandsError Responses Meaning Operator Selection +COPS Orange Orange networks have been detectedCalls only Network Command syntax AT+CREG= mode Network Registration +CREGOr 1 is selected Result code Operator List Management +WOLM Created Read Operator Name +WOPN CphsROM AT+WOPN=? AT+WOPN=3,0 MemoryAT+WOPN=4 Used for Plmn names EFPLMNsel will be selected Command syntax AT+CPLS= ListSelection of Preferred Plmn List +CPLS Preferred Operator List +CPOL Present and can be selectedCan be selected Defined values List EFPLMNsel present Alphanumeric format EFPLMNsel presentEFPLMNwact present EFPLMNwact present Selected Command syntax AT+COPN Read Operator Name +COPNAT+COPN AT+COPN=? Security Commands Enter PIN +CPIN OnCell G2150I AT Command Set Security CommandsCommand syntax AT+CPIN=pin Enter PIN2 +CPIN2 Command syntax AT+CPINC PIN Remaining Attempt Number +CPINC Facility Lock +CLCK Lock, no information on Call barringNo longer supported in GSM Data calls OnCell G2150I AT Command Set Security Commands Change Password +CPWD AT+CPWD=?Maximum 4 mini. For call barring, on 4 digits Maximum Short Message Commands OnCell G2150I AT Command SetShort Message Commands Parameter Definitions Select Message Service +CSMS OnCell G2150I AT Command Set Short Message CommandsDefined values service Command syntax in text mode AT+CNMA GSM 07.05 Phase 2 + version Error in MSMemory capacity exceeded SIM memory storage is full Preferred Message Storage +CPMS Command syntax AT+CMGF=mode Preferred Message Format +CMGFAT+CMGF? +CMGF1 AT+CMGF=? AT+CMGF=0 AT+CMGS=14CR Show Text Mode Parameters +CSDH Save Settings +CSASRestore Settings +CRES AT+CMTI SM,1 New Message Indication +CNMIAT+CSDH=0 AT+CSDH? Command syntax AT+CMGR=index Response syntax for text mode Read Message +CMGR Command syntax AT+CMGL=stat Response syntax for text mode List Message +CMGLAlphafield Memory at index Then have their status changed to REC Read Text modeSend Message +CMGS Write Message to Memory +CMGW Set Text Mode Parameters +CSMP Send Message From Storage +CMSSDestination number Format Delete Message +CMGD VP value Validity period valueAT+CMGR=3 AT+CMGD=3 Service Center Address +CSCA Command syntax AT+CSCA=scaLocation 1 is deleted Deleted Cell Broadcast Message Identifiers +WCBM Command syntax AT+WCBM=midsSelect Cell Broadcast Message Types +CSCB PDU Mode Text Mode Command syntax AT+WMGO=locMessage Status Modification +WMSC Message Overwriting +WMGO Un-change SMS Status +WUSS Was reinitialized Copy Messages +WMCP SIM to the Flash SIM is the total memory available in SIM SMSFlash Writing and ME for storing Defined values mode Copy mode Command syntax AT+CMMS = modeDefined values mode 0 Disable feature More Messages to Send +CMMS Data Commands Using AT Commands During a Data Connection OnCell G2150I AT Command Set Data CommandsBearer Type Selection +CBST Defined values speed Select Mode +FCLASS Service Reporting Control +CROnCell G2150I AT Command SetData Commands Command syntax AT+FCLASS= n Command syntax AT+CR=mode Command syntax AT+CRC=modeCellular Result Codes +CRC DTE-DCE Local Rate Reporting +ILRR AT+ILRR=? Radio Link Protocol Parameters +CRLPAT+ILRR=0 AT+ILRR=1 AT+ILRR? Select Data Compression %C V42 bis Data Compression +DSAT%C0 AT%C2 AT%C? AT+DS=? V42 bis Data Compression Report +DR Select Data Error Correcting Mode \NCommand syntax AT+DR=status V24-V25 Commands OnCell G2150I AT Command Set V24-V25 Commands Fixed DTE Rate +IPRRecommendation the first set of values indicates the range Auto-detectable baud rates including 0. The second set Defined values format DTE-DCE Character Framing +ICFDTE-DCE Local Flow Control +IFCR Set DCD Signal &C Set DTR Signal &DCommand syntax AT&Cn Command syntax AT&Dn Result Code Suppression Q Set DSR Signal &SBack to Online Mode O Default Configuration Z Save Configuration &WDCE Response Format Information responses OnCell G2150I AT Command SetV24-V25 Commands Command syntax AT&TnCommand syntax ATEn Auto-tests &T Restore Factory Settings &F Display Configuration &VCommand syntax AT&Fn Cancellation Identifications Command syntax ATInRequest Identification Data / Commands Multiplexing +WMUX AT+WMUX=?AT+WMUX? AT+WMUX=1 Gprs Commands 10-2 OnCell G2150I AT Command Set Gprs CommandsDefine PDP Context + Cgdcont 10-3 Quality of Service Profile Requested +CGQREQAT+CGQREQ? AT+CGQREQ=? 10-4 GMM/SM 10-5 Quality of Service Profile Minimum acceptable +CGQMIN 10-6 Gprs Attach or Detach +CGATT 10-7 PDP Context Activate or Deactivate +CGACT 10-8 10-9 Enter Data State +CGDATAGprs Mobile Station Class +CGCLASS Select Service for MO SMS Messages +CGSMS AT+CGCLASS=? +CGCLASS CG,CC AT+CGCLASS? +CGCLASS CCExample about automatic attachment see remark above 10-10 Gprs Event Reporting +CGEREP 10-11 10-12 OnCell G2150I AT Command SetGPRS CommandsGprs Network Registration Status +CGREG 10-13 Request Gprs IP Service ‘D’Example Network Requested PDP Context Activation 10-14 10-15 +CGAUTO?+CGAUTO=? +CGANS=? 10-16 10-17 Show PDP Address +CGPADDR+CGPADDR=? 10-18 Command syntax AT+CRForm GSM recommendation 04.08 or specific. Call 10-19 Gprs Parameter Customization + WgprsContext 10-20 10-21 Full AT Gprs Command ExamplesActivation of an IP PDP context Example Network request 10-22 Moxa Proprietary Commands 11-2 Firmware Upgrade *UPGOnCell G2150I AT Command Set Moxa Proprietary Commands 11-3 Restore Default Setting *DEFAULTOnCell G2150I AT Command SetMOXA Proprietary Commands 11-4 Automatic PIN Entry *USEPINAT*USERPIN=0 AT*USEPIN? Initial Strings *BOOTSTR Command syntax AT*BOOTSTR=mAT*BOOTSTR=1 AT*BOOTSTR=0 11-5 Serial Port Configuration *SERIAL AT*SERIAL?AT*SERIAL=? 11-6 SMS Tunnel Mode *SMS 11-7 AT*SMSTUN=1 Smsout 11-8 Result Codes, Failure Causes, and Other Tables ME Error Result Code +CME Error error Error Meaning Resulting from the following commands Meaning Resulting from the following commands Message Service Failure Result Code +CMS Error erSpecific Error Result Codes Cause Value Diagnostic Failure Cause from GSM 04.08 Recommendation +CEER Facility rejected Specific Failure Cause for +CEER GSM 04.11 Annex E-2 Mobile Originating SM-Transfer Cause No Congestion PDU SMS Unsolicited Result CodesVerbose Result Code Numeric V0 set Description Verbose Result Code Numeric Description Set Final Result Codes+CIEV Intermediate Result Codes Verbose Result Code Numeric V0 set Description