[NETWORK] menu

■■[E-mail set up] page

E-mail address set in advance for use when there is a problem or when the usage time of a lamp reaches a set value.

E-mail can be sent to (maximum two locations). Click [Detailed set up] → [E-mail set up].

 

 

 

 

 

 

 

 

 

 

 

 

(1)

[ENABLE]

 

 

 

 

 

 

 

 

 

 

 

 

 

Select [Enable] to use the E-mail function.

 

 

 

 

 

 

 

 

 

 

 

 

(2)

[SMTP SERVER NAME]

 

 

 

 

 

 

 

 

 

 

(1)

 

Enter the IP address or the server name of the E-mail

 

 

 

 

 

 

 

 

 

 

 

 

 

server (SMTP). To enter the server name, the DNS

 

 

 

 

 

 

 

 

 

 

(2)

 

server settings are required.

 

 

 

 

 

 

 

 

 

 

(3)

(3)

[MAIL FROM]

 

 

 

 

 

 

 

 

Enter the E-mail address of the projector. (Up to 63

 

 

 

 

 

 

 

 

 

(4)

 

characters in single byte)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(4)

[MEMO]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(5)

 

You can enter information such as the location of the

 

 

 

 

 

 

projector that notifies the sender of the E-mail. (Up to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(6)

 

63 characters in single byte)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(5)

[MINIMUM TIME]

 

 

 

 

 

 

 

 

 

 

 

 

 

Change the minimum interval for the temperature

 

 

 

 

 

 

 

 

 

 

 

 

 

warning mail. The default value is 60 minutes. In this

 

 

 

 

 

 

 

 

 

 

 

 

 

case, another E-mail will not be sent for 60 minutes

 

 

 

 

 

 

 

 

 

 

 

 

 

after sending the temperature warning mail even if it

 

 

 

 

 

 

 

 

 

 

 

 

 

reaches the warning temperature.

 

 

 

 

 

 

 

 

 

 

 

 

(6)

[INTAKE AIR TEMPERATURE]

 

 

 

 

 

 

 

 

 

 

 

 

 

Change the temperature setting for the temperature

 

 

 

 

 

 

 

 

 

 

 

 

 

warning mail. A temperature warning mail is sent

 

 

 

 

 

 

 

 

 

 

 

 

 

when the temperature exceeds this value.

 

 

 

 

 

 

 

 

 

 

 

 

(7)

[E-MAIL ADDRESS 1]

 

 

 

 

 

 

 

 

 

 

 

 

 

Enter the E-mail address to be sent.

 

 

 

 

 

 

 

 

 

 

 

 

(8)

Settings of the conditions to send E-mail

 

 

 

 

 

 

 

 

 

 

 

 

 

Select the conditions to send E-mail.

 

 

 

 

 

 

 

 

 

 

 

(7)

 

[MAIL CONTENTS]:

 

 

 

 

 

 

 

 

 

 

 

 

Select either [NORMAL] or [SIMPLE].

 

 

 

 

 

 

 

 

 

 

 

 

 

[ERROR]:

 

 

 

 

 

 

 

 

 

 

 

 

 

An E-mail message is sent when an error

 

 

 

 

 

 

 

 

 

 

 

(8)

 

occurred in the self-diagnosis.

 

 

 

 

 

 

 

 

 

 

 

 

[LAMP1 RUNTIME]:

 

 

 

 

 

 

 

 

 

 

 

 

An E-mail message is sent when the remaining lamp on time for the lamp 1 has reached the value set at the right field.

[LAMP2 RUNTIME]:

An E-mail message is sent when the remaining lamp on time for the lamp 2 has reached the value set at the right field.

[LAMP3 RUNTIME]:

An E-mail message is sent when the remaining lamp on time for the lamp 3 has reached the value set at the right field.

[LAMP4 RUNTIME]:

An E-mail message is sent when the remaining lamp on time for the lamp 4 has reached the value set at the right field.

[INTAKE AIR TEMPERATURE]:

An E-mail message is sent when the air intake temperature has reached the value set at the above field.

[PERIODIC REPORT]:

Place a check mark on this when E-mail is to be sent periodically.

It will be sent on the days and time with the check mark.

Note

zzSet each item of [LAMP1 RUNTIME] to [LAMP4 RUNTIME] to 500 hours or less when using the optional accessory replacement lamp unit (for portrait mode) (Model No.: ET-LAD510P (1 pc), ET-LAD510PF (4 pcs)).

Settings

ENGLISH - 135