Setting the Cross-Connect Modes | Paradyne 8779, U8777 manual

4. Cross-Connecting Ports

Setting the Cross-Connect Modes

To access the Set Cross-Connect Mode screen, follow this menu selection sequence:

Main Menu → Configuration → Current Configuration → Cross-Connect→

Set Cross-Connect Mode

When the screen is first displayed, all ports are set to DS1 Bypass mode. In this example, Ports 1 and 2 have been changed to DS0 Cross-connect, and Ports 3 –8 have been changed to DS1 Bypass. Unassigned appears next to Ports 1 and 2 because time slots associated with the cross-connection have not yet been assigned.

main/config/xconnect_mode
Slot: 18			Model: 8777
	CROSS-CONNECT MODE
DSX-1 Port	MODE		DSL Port
1	DS0 Cross-connect		Unassigned
2	DS0 Cross-connect		Unassigned
3	DS1 Bypass		3
4	DS1 Bypass		4
5	DS1 Bypass		5
6	DS1 Bypass		6
7	DS1 Bypass		7
8	DS1 Bypass		8

Assign_DS0s

-------------------------------------------------------------------------------

Ctrl-a to access these functions, ESC for previous menu	MainMenu Exit
Save	Clear_All

4-4

May 2002

8700-A2-GB20-40

Image 40

Paradyne 8779, U8777 manual Setting the Cross-Connect Modes

Contents

Hotwire TDM Sdsl Termination Units Copyright 2002 Paradyne Corporation All rights reserved Contents Cross-Connecting Ports Monitoring and TroubleshootingIP Addressing Security Transferring Firmware and Configurations Using Tftp TestingConfiguration Options Connector Pin Assignments Technical Specifications Cross-Connection WorksheetsStandards Compliance for Snmp Traps Index New Features for this Release About This GuideDocument Purpose and Intended Audience Document Summary Product-Related Documents Document Number Document Title About Hotwire 8777 TDM Sdsl Units TDM Sdsl Overview TDM Sdsl Features Model Has eight Eight Customer Premises CP Network ConfigurationCO Site Management Information Base MIB Support Snmp Management CapabilitiesSnmp Trap Support Using the Asynchronous Terminal Interface User Interface AccessManagement Serial Port Settings Documents in About This Guide Login Logging In to the Hotwire DslamInitiating an ATI Session Select Main Menu Menu Hierarchy Inband Main Menu → Configuration → Current Configuration→ Network Screen Work AreasFunction Keys Keyboard Keys Navigating the ScreensPress Function Keys For the screen Function Select Press Enter to Switching Between Screen Work Areas Example Ending an ATI Session Exiting From the Dslam Session Using the Asynchronous Terminal Interface May Initial Startup and Configuration Overview Main Menu → Control→ Change Identity Entering Identity InformationIdentity Configuration Options Configuring the UnitConfiguration Option Area Configuration Option Set Accessing and Displaying Configuration Options Main Menu → Configuration Load Configuration FromLoad Configuration from If you select Then Current and Default Factory Configurations Configuration EDIT/DISPLAY Select Access To Configure Table A-5 Configuration Loader Main Menu → Configuration → Configuration LoaderConfiguration Loader DSL Completed successfully Saving Configuration Options Save Configuration Restoring Access to the User Interface Resetting the Device Resetting AutoRate Main Menu → Configuration → Current Configuration → NetworkMain Menu → Control → Reset AutoRate Disabling AutoRate Main Menu → Control → Download Code Downloading FirmwareDownload Code Apply Download Initial Startup and Configuration May Cross-Connecting Ports Determining the Configuration DSL Setting the Cross-Connect Modes Mode Data or v Voice = DSL = DSX-1 Assigning Time SlotsSlots of DSL Ports 1 Following example shows the configuration for DSX-1 Port Assign Time Slots CROSS-CONNECT Mode Cross-Connecting Ports May Configurations Not Running IP Conservative Software Configuration OptionsIP Addressing Selecting an IP Addressing Scheme Appendix A, Configuration Options All ConfigurationsIP Addressing Example Security ATI Access Levels Administer Logins Creating a LoginLogin Entry Deleting a Login On the Login Entry Screen, for Enter Controlling Snmp Access Assigning Snmp Community Names and Access TypesManagement Options, in Appendix A, Configuration Options Configuration Options, to Security May Monitoring and Troubleshooting What to Monitor Main Menu → Status→ System and Test Status Viewing System and Test StatusSystem and Test Status Health and Status SELF-TEST Results Health and Status Messages Yyyyyyyy Monitoring and Troubleshooting See Network Interface Options See G.703 Interface Options Self-Test Results Messages DTE Monitoring and Troubleshooting Test Status Messages Test Status Messages Meaning Device Messages Device Messages 1 What Message Indicates What To Do Performance Statistics Device Messages 2 What Message Indicates What To Do Viewing Network Error Statistics Network Error Statistics Viewing Network Performance Statistics Field Contains Field Contains Viewing DSX-1 Performance Statistics Performance Statistics Field Contains Viewing G.703 Performance Statistics Interval is displayed. When zero, the port is disabled SES Viewing Current Network Performance StatisticsFebe Viewing Inband Management Statistics Inband Management Statistics Dlci Viewing LED Status System Display LEDs Screen Type Label Value is Indicating System Front Panel LEDs LED is Indicating Troubleshooting 1 Symptom Possible Cause Solutions TroubleshootingChanging the Meaning of the Ports LEDs Troubleshooting 2 Symptom Possible Cause Solutions Testing Testing Accessing the Test MenuMain Menu → Test Test Network & DSX-1 Tests Running Network TestsNetwork & G.703 Tests 8700-A2-GB20-40 May Network Line Loopback Repeater Loopback DTE Loopback Remote Send Line Loopback Send and Monitor Device Tests Lamp TestMain Menu → Test→ Device Tests Device Tests Ending an Active Test Telco-Initiated Tests Telco-Initiated Line LoopbackTelco-Initiated Payload Loopback Activation Line Payload Remote Line Deactivation Loopback Telco-Initiated Remote Line Loopback Transferring Firmware and Configurations Using Tftp DSL1 Transferring Firmware and Configurations Using Tftp Procedure Configuration Loader Completed successfully Transferring Firmware and Configurations Using Tftp May Configuration Options Select To Access To Configure Network Interface Options Menu Table A-1. Network Interface Options 1Port Status Margin Threshold Table A-1. Network Interface Options 2 Excessive Error Rate ThresholdAutoRate Possible Settings 001.000.000.000 223.255.255.255, Clear Table A-1. Network Interface Options 3Transmit Attenuation Peer IP Address DS0 Cross Connect Line Framing Table A-1. Network Interface Options 4Circuit Identifier Configuration Options Main Menu → Configuration → Current Configuration → DSX-1 DSX-1 Interface Options ModelTable A-4. DSX-1 Interface Options Model 8777 1 Line Coding Format Line Framing Table A-4. DSX-1 Interface Options Model 8777 2Primary Clock Source Main Menu → Configuration → Current Configuration → G.703 Interface Options ModelTable A-5. G.703 Interface Options Model 8779 1 Interface Options Framing Table A-5. G.703 Interface Options Model 8779 2Line Coding Table A-5. G.703 Interface Options Model 8779 3 Copy Ports Options Table A-6. Copy Port OptionsFrom Port n To Port y DSL Mode Test TimeoutSystem Options Table A-7. System Options 1 Table A-7. System Options 2 Test Duration minTelco Initiated Loopback Remote Telco Line Loopback System Clock System Clock Figure A-1. System Timing Figure A-2. System Clock Configuration Examples Table A-8. System Clock Options CROSS-CONNECT Configuration Cross-Connect Setting Cross-Connect Mode Following screen is displayed for Model Mode DSL Table A-9. Cross-Connect Mode Options Model DSL Port Table A-10. Cross-Connect Mode Options Model Source Assigning Time Slots Following screen is displayed for a DSX-1 port Model Time Slot Number Assign Time Slots DSL Table A-11. Assign Time Slots Options 1 DSX-1/DSL or G.703/DSLPort Type Port Table A-11. Assign Time Slots Options 2 Start TSAssign To Data or Voice Telnet Session Options Management and Communication Options MenuTelnet Session Options Table A-12. Telnet Session Options General Snmp Management Options Table A-13. General Snmp Management Options 1Snmp Management General Snmp Management Options Name 1 Access Name 2 AccessTable A-13. General Snmp Management Options 2 Community Name Snmp NMS Security Options Snmp NMS Security OptionsNMS Table A-14. Snmp NMS Security Options Access TypeNMS IP Validation Snmp Traps Options Snmp Traps Options Table A-15. Snmp Traps Options 1 Snmp Traps Link Traps Possible Settings Disable, Up, Down, Both Table A-15. Snmp Traps Options 2Enterprise Specific Traps Link Traps Interfaces Inband Management Channel Inband Management Channel ModelPPP Table A-16. Inband Management Channel Options Model Configuring and Testing Inband Management Cross Connect Mode screen appears Cross Connect Mode Following screen appears = Ibmc Configuration Options Standards Compliance for Snmp Traps Snmp TrapsIfIndex IfIndex Description AuthenticationFailure WarmStartLinkUp and linkDown Snmp Trap Description Possible Cause LinkUp/DownTvariable bindings Enterprise-Specific Traps IfType RFC 8700-A2-GB20-40 May May Connector Pin Assignments Front Panel 50-pin DTE Connector Pinouts Connector Pin Assignments Table C-2. Rear Connector Pinouts Connector Pins Port Tip, Ring Connector Pin Assignments May Technical Specifications Technical Specifications May Using the Worksheets Cross-Connection Worksheets Port Connection Diagram Time Slot Assignments DSX-1 Port DSX-1 Time Slot AssignmentsTS01 Time Slot Assignments DSX-1 Port Time Slot Assignments DSX-1 Port Time Slot Assignments DSX-1 Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments Time Slot Assignments G.703 Port Time Slot Assignments G.703 Port Time Slot Assignments G.703 Port Time Slot Assignments G.703 Port Time Slot Assignments G.703 Port Time Slot Assignments G.703 Port Time Slot Assignments G.703 Port Time Slot Assignments G.703 Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Index Snmp IN-2 IN-3 IN-4 IN-5 IN-6