Viewing DSX-1 Performance Statistics | Paradyne U8777, 8779 specification

7. Monitoring and Troubleshooting

Viewing DSX-1 Performance Statistics

DSX-1 performance statistics allow you to monitor the current status of the DSX-1 interface when ESF framing is selected.

To view DSX-1 Performance Statistics, follow this menu selection sequence:

Main Menu → Status→ Performance Statistics→ DSX-1 Performance Statistics

main/status/performance/DSX-1
Slot:	4			Model: 87xx
Port:	2	DSX-1	PERFORMANCE STATISTICS
Current Interval Timer:			2	Error Events Counter: 0000

-------------------------------------------------------------------------------

		--ES--	--UAS--	--SES--	--BES--	--CSS--	-LOFC- -Status-
Current Int:		000	000	000	000	000	000	Y
Interval	01	000	000	000	000	000	000	none
Interval	02	000	000	000	000	000	000	none
Interval	03	000	000	000	000	000	000	none
Interval	04	000	000	000	000	000	000	none
Interval	05	000	000	000	000	000	000	none
Interval	06	000	000	000	000	000	000	none
Interval	07	000	000	000	000	000	000	none
Worst Interval:		24	14	14	09	18	12
Tot (valid 96): 00010			00000	00000	00000	0020	0000

-------------------------------------------------------------------------------

Ctrl-a to access these functions, ESC for previous menu			MainMenu Exit
PgUp	PgDn	ClrStats

he following DSX-1 Performance Statistics are collected:

ES (Errored Seconds): Seconds during which one or more Extended

Superframe (ESF) events occurred. Maximum value is 900.

UAS (Unavailable Seconds): Seconds during which service is unavailable. UAS is received at the start of 10 consecutive SES and cleared at the start of 10 seconds with no SES. Maximum value is 900.

SES (Severely Errored Seconds): Seconds during which 320 or more CRC error events or at least one Out of Frame (OOF) event occurred. Maximum value is 900.

BES (Bursty Errored Seconds): Contains the number of bursty errored seconds for the current interval. A bursty errored second is any second with more than one but less than 320 CRC errors. Maximum value is 900.

CSS (Controlled Slip Seconds): Seconds during which one or more

Tcontrolled slips (as defined in TR 54016) occurred. Maximum value is 900.

LOFC (Loss of Frame Count): Contains the number of times that an LOF is declared. Maximum value is 255.

8700-A2-GB20-40

May 2002

7-15

Image 67

Paradyne U8777, 8779 manual Viewing DSX-1 Performance Statistics

Contents

Hotwire TDM Sdsl Termination Units Copyright 2002 Paradyne Corporation All rights reserved Contents Security Cross-Connecting PortsMonitoring and Troubleshooting IP Addressing Transferring Firmware and Configurations Using Tftp TestingConfiguration Options Index Connector Pin AssignmentsTechnical Specifications Cross-Connection Worksheets Standards Compliance for Snmp Traps Document Summary New Features for this ReleaseAbout This Guide Document Purpose and Intended Audience Document Number Document Title Product-Related Documents TDM Sdsl Overview About Hotwire 8777 TDM Sdsl Units Model Has eight Eight TDM Sdsl Features Customer Premises CP Network ConfigurationCO Site Management Information Base MIB Support Snmp Management CapabilitiesSnmp Trap Support Documents in About This Guide Using the Asynchronous Terminal InterfaceUser Interface Access Management Serial Port Settings Login Logging In to the Hotwire DslamInitiating an ATI Session Main Menu Select Inband Menu Hierarchy Keys Main Menu → Configuration → Current Configuration→ NetworkScreen Work Areas Function Keyboard Keys Navigating the ScreensPress For the screen Function Select Press Enter to Function Keys Example Switching Between Screen Work Areas Exiting From the Dslam Session Ending an ATI Session Using the Asynchronous Terminal Interface May Overview Initial Startup and Configuration Main Menu → Control→ Change Identity Entering Identity InformationIdentity Configuration Options Configuring the UnitConfiguration Option Area Configuration Option Set If you select Then Accessing and Displaying Configuration OptionsMain Menu → Configuration Load Configuration From Load Configuration from Configuration EDIT/DISPLAY Current and Default Factory Configurations Table A-5 Select Access To Configure DSL Configuration LoaderMain Menu → Configuration → Configuration Loader Configuration Loader Completed successfully Save Configuration Saving Configuration Options Resetting the Device Restoring Access to the User Interface Disabling AutoRate Resetting AutoRateMain Menu → Configuration → Current Configuration → Network Main Menu → Control → Reset AutoRate Main Menu → Control → Download Code Downloading FirmwareDownload Code Apply Download Initial Startup and Configuration May Cross-Connecting Ports Determining the Configuration DSL Mode Setting the Cross-Connect Modes Data or v Voice = DSL = DSX-1 Assigning Time SlotsSlots of DSL Ports 1 Assign Time Slots Following example shows the configuration for DSX-1 Port CROSS-CONNECT Mode Cross-Connecting Ports May Selecting an IP Addressing Scheme Configurations Not Running IP Conservative SoftwareConfiguration Options IP Addressing Appendix A, Configuration Options All ConfigurationsIP Addressing Example Security ATI Access Levels Administer Logins Creating a LoginLogin Entry On the Login Entry Screen, for Enter Deleting a Login Configuration Options, to Controlling Snmp AccessAssigning Snmp Community Names and Access Types Management Options, in Appendix A, Configuration Options Security May What to Monitor Monitoring and Troubleshooting Main Menu → Status→ System and Test Status Viewing System and Test StatusSystem and Test Status Health and Status SELF-TEST Results Yyyyyyyy Health and Status Messages Monitoring and Troubleshooting See Network Interface Options See G.703 Interface Options DTE Self-Test Results Messages Monitoring and Troubleshooting Test Status Messages Meaning Test Status Messages Device Messages 1 What Message Indicates What To Do Device Messages Device Messages 2 What Message Indicates What To Do Performance Statistics Network Error Statistics Viewing Network Error Statistics Field Contains Viewing Network Performance Statistics Field Contains Performance Statistics Viewing DSX-1 Performance Statistics Field Contains Viewing G.703 Performance Statistics Interval is displayed. When zero, the port is disabled SES Viewing Current Network Performance StatisticsFebe Inband Management Statistics Viewing Inband Management Statistics Dlci System Viewing LED Status System Display LEDs Screen Type Label Value is Indicating LED is Indicating Front Panel LEDs Troubleshooting 1 Symptom Possible Cause Solutions TroubleshootingChanging the Meaning of the Ports LEDs Testing Troubleshooting 2 Symptom Possible Cause Solutions Test TestingAccessing the Test Menu Main Menu → Test Network & DSX-1 Tests Running Network TestsNetwork & G.703 Tests 8700-A2-GB20-40 May Network Line Loopback Repeater Loopback DTE Loopback Remote Send Line Loopback Send and Monitor Device Tests Device TestsLamp Test Main Menu → Test→ Device Tests Ending an Active Test Activation Line Payload Remote Line Deactivation Loopback Telco-Initiated TestsTelco-Initiated Line Loopback Telco-Initiated Payload Loopback Telco-Initiated Remote Line Loopback DSL1 Transferring Firmware and Configurations Using Tftp Transferring Firmware and Configurations Using Tftp Procedure Configuration Loader Completed successfully Transferring Firmware and Configurations Using Tftp May Select To Access To Configure Configuration Options Margin Threshold Network Interface Options MenuTable A-1. Network Interface Options 1 Port Status Table A-1. Network Interface Options 2 Excessive Error Rate ThresholdAutoRate Peer IP Address Possible Settings 001.000.000.000 223.255.255.255, ClearTable A-1. Network Interface Options 3 Transmit Attenuation DS0 Cross Connect Line Framing Table A-1. Network Interface Options 4Circuit Identifier Configuration Options Line Coding Format Main Menu → Configuration → Current Configuration → DSX-1DSX-1 Interface Options Model Table A-4. DSX-1 Interface Options Model 8777 1 Line Framing Table A-4. DSX-1 Interface Options Model 8777 2Primary Clock Source Interface Options Main Menu → Configuration → Current Configuration → G.703Interface Options Model Table A-5. G.703 Interface Options Model 8779 1 Framing Table A-5. G.703 Interface Options Model 8779 2Line Coding Table A-5. G.703 Interface Options Model 8779 3 To Port y Copy Ports OptionsTable A-6. Copy Port Options From Port n Table A-7. System Options 1 DSL ModeTest Timeout System Options Remote Telco Line Loopback Table A-7. System Options 2Test Duration min Telco Initiated Loopback System Clock System Clock Figure A-1. System Timing Figure A-2. System Clock Configuration Examples Table A-8. System Clock Options Cross-Connect CROSS-CONNECT Configuration Following screen is displayed for Model Setting Cross-Connect Mode Mode DSL DSL Port Table A-9. Cross-Connect Mode Options Model Source Table A-10. Cross-Connect Mode Options Model Following screen is displayed for a DSX-1 port Model Assigning Time Slots Assign Time Slots DSL Time Slot Number Port Table A-11. Assign Time Slots Options 1DSX-1/DSL or G.703/DSL Port Type Data or Voice Table A-11. Assign Time Slots Options 2Start TS Assign To Telnet Session Options Management and Communication Options MenuTelnet Session Options Table A-12. Telnet Session Options General Snmp Management Options General Snmp Management OptionsTable A-13. General Snmp Management Options 1 Snmp Management Community Name Name 1 AccessName 2 Access Table A-13. General Snmp Management Options 2 Snmp NMS Security Options Snmp NMS Security OptionsNMS Table A-14. Snmp NMS Security Options Access TypeNMS IP Validation Snmp Traps Options Snmp Traps Options Snmp Traps Table A-15. Snmp Traps Options 1 Link Traps Interfaces Link Traps Possible Settings Disable, Up, Down, BothTable A-15. Snmp Traps Options 2 Enterprise Specific Traps Inband Management Channel Inband Management Channel ModelPPP Table A-16. Inband Management Channel Options Model Configuring and Testing Inband Management Cross Connect Mode Cross Connect Mode screen appears = Ibmc Following screen appears Configuration Options IfIndex Description Standards Compliance for Snmp TrapsSnmp Traps IfIndex Snmp Trap Description Possible Cause AuthenticationFailureWarmStart LinkUp and linkDown LinkUp/DownTvariable bindings Enterprise-Specific Traps IfType RFC 8700-A2-GB20-40 May May Front Panel 50-pin DTE Connector Pinouts Connector Pin Assignments Connector Pin Assignments Port Tip, Ring Table C-2. Rear Connector Pinouts Connector Pins Connector Pin Assignments May Technical Specifications Technical Specifications May Cross-Connection Worksheets Using the Worksheets Port Connection Diagram Time Slot Assignments DSX-1 Port DSX-1 Time Slot AssignmentsTS01 Time Slot Assignments DSX-1 Port Time Slot Assignments DSX-1 Port Time Slot Assignments DSX-1 Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments G.703 Port Time Slot Assignments Time Slot Assignments G.703 Port Time Slot Assignments G.703 Port Time Slot Assignments G.703 Port Time Slot Assignments G.703 Port Time Slot Assignments G.703 Port Time Slot Assignments G.703 Port Time Slot Assignments G.703 Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Snmp Index IN-2 IN-3 IN-4 IN-5 IN-6