Manuals / Paradyne / Computer Equipment / Network Hardware

Paradyne 8779, U8777 manual Viewing Network Error Statistics

Models: U8777 8779

1 182

Download 182 pages 21.75 Kb

Page 64

7. Monitoring and Troubleshooting

Viewing Network Error Statistics

The terminal unit maintains error statistics on the network DSL interface for each port.

To view Network Error Statistics, follow this menu selection sequence:

Main Menu → Status→ Performance Statistics→ Network Error Statistics

main/status/performance/net_error
Slot: 4:		Model: 87xx
Port: 2	NETWORK ERROR STATISTICS
Current Interval Timer: 002		Error Events Counter: 0034

-------------------------------------------------------------------------------

	---ES		---	---SES	---	--FEBE--		-Complete-
	Near		Far	Near Far		Near	Far	Near Far
Current Int:	000		000	000	000	000	000	Yes	No
Interval 01	000		000	000	000	000	000	Yes	Yes
Interval 02	000		000	000	000	000	000	Yes	Yes
Interval 03	000		000	000	000	000	000	Yes	Yes
Interval 04	000		000	000	000	000	000	Yes	Yes
Interval 05	000		000	000	000	000	000	Yes	Yes
Interval 06	000		000	000	000	000	000	Yes	Yes
Interval 07	000		000	000	000	000	000	Yes	Yes
Worst Interval: 24			09	14	08	18	18
Near Tot(valid):		00010		00000		00000
Far Tot (valid):		00010		00000		00000

-------------------------------------------------------------------------------

Ctrl-a to access these functions, ESC for previous menu			MainMenu Exit
PgUp	PgDn	ClrNear ClrFar

he following Network Error Statistics are collected for the selected port:

ES (Errored Seconds): Seconds during which one or more Cyclical

Redundancy Check (CRC) error events occurred. Maximum value is 900.

SES (Severely Errored Seconds): Seconds during which more than 320 or more CRC error events occurred. Maximum value is 900.

FEBE (Far-End Block Errors): Errors reported by the remote equipment.

TMaximum value is 900.

Complete: Whether the interval register contains data for all 900 seconds of the interval.

7-12

May 2002

8700-A2-GB20-40

Image 64

Paradyne 8779, U8777 manual Viewing Network Error Statistics

Contents

Hotwire TDM Sdsl Termination Units Copyright 2002 Paradyne Corporation All rights reserved Contents Cross-Connecting Ports Monitoring and TroubleshootingIP Addressing SecurityTransferring Firmware and Configurations Using Tftp TestingConfiguration Options Connector Pin Assignments Technical Specifications Cross-Connection WorksheetsStandards Compliance for Snmp Traps IndexNew Features for this Release About This GuideDocument Purpose and Intended Audience Document SummaryProduct-Related Documents Document Number Document TitleAbout Hotwire 8777 TDM Sdsl Units TDM Sdsl OverviewTDM Sdsl Features Model Has eight EightCustomer Premises CP Network ConfigurationCO Site Management Information Base MIB Support Snmp Management CapabilitiesSnmp Trap Support Using the Asynchronous Terminal Interface User Interface AccessManagement Serial Port Settings Documents in About This GuideLogin Logging In to the Hotwire DslamInitiating an ATI Session Select Main MenuMenu Hierarchy InbandMain Menu → Configuration → Current Configuration→ Network Screen Work AreasFunction KeysKeyboard Keys Navigating the ScreensPress Function Keys For the screen Function Select Press Enter toSwitching Between Screen Work Areas ExampleEnding an ATI Session Exiting From the Dslam SessionUsing the Asynchronous Terminal Interface May Initial Startup and Configuration OverviewMain Menu → Control→ Change Identity Entering Identity InformationIdentity Configuration Options Configuring the UnitConfiguration Option Area Configuration Option Set Accessing and Displaying Configuration Options Main Menu → Configuration Load Configuration FromLoad Configuration from If you select ThenCurrent and Default Factory Configurations Configuration EDIT/DISPLAYSelect Access To Configure Table A-5Configuration Loader Main Menu → Configuration → Configuration LoaderConfiguration Loader DSLCompleted successfully Saving Configuration Options Save ConfigurationRestoring Access to the User Interface Resetting the DeviceResetting AutoRate Main Menu → Configuration → Current Configuration → NetworkMain Menu → Control → Reset AutoRate Disabling AutoRateMain Menu → Control → Download Code Downloading FirmwareDownload Code Apply Download Initial Startup and Configuration May Cross-Connecting Ports OverviewDetermining the Configuration DSL Setting the Cross-Connect Modes ModeData or v Voice = DSL = DSX-1 Assigning Time SlotsSlots of DSL Ports 1 Following example shows the configuration for DSX-1 Port Assign Time SlotsCROSS-CONNECT Mode ModeCross-Connecting Ports May Configurations Not Running IP Conservative Software Configuration OptionsIP Addressing Selecting an IP Addressing SchemeAppendix A, Configuration Options All ConfigurationsIP Addressing Example Security OverviewATI Access Levels Administer Logins Creating a LoginLogin Entry Deleting a Login On the Login Entry Screen, for EnterControlling Snmp Access Assigning Snmp Community Names and Access TypesManagement Options, in Appendix A, Configuration Options Configuration Options, toSecurity May Monitoring and Troubleshooting What to MonitorMain Menu → Status→ System and Test Status Viewing System and Test StatusSystem and Test Status Health and Status SELF-TEST Results Health and Status Messages YyyyyyyyMonitoring and Troubleshooting See Network Interface Options See G.703 Interface Options Self-Test Results Messages DTEMonitoring and Troubleshooting Test Status Messages Test Status Messages MeaningDevice Messages Device Messages 1 What Message Indicates What To DoPerformance Statistics Device Messages 2 What Message Indicates What To DoViewing Network Error Statistics Network Error StatisticsViewing Network Performance Statistics Field ContainsField Contains Viewing DSX-1 Performance Statistics Performance StatisticsField Contains Viewing G.703 Performance Statistics Interval is displayed. When zero, the port is disabled SES Viewing Current Network Performance StatisticsFebe Viewing Inband Management Statistics Inband Management StatisticsDlci Viewing LED Status SystemDisplay LEDs Screen Type Label Value is Indicating SystemFront Panel LEDs LED is IndicatingTroubleshooting 1 Symptom Possible Cause Solutions TroubleshootingChanging the Meaning of the Ports LEDs Troubleshooting 2 Symptom Possible Cause Solutions TestingTesting Accessing the Test MenuMain Menu → Test TestNetwork & DSX-1 Tests Running Network TestsNetwork & G.703 Tests 8700-A2-GB20-40 May Network Line Loopback Repeater Loopback DTE Loopback Remote Send Line Loopback Send and Monitor Device Tests Lamp TestMain Menu → Test→ Device Tests Device TestsEnding an Active Test Telco-Initiated Tests Telco-Initiated Line LoopbackTelco-Initiated Payload Loopback Activation Line Payload Remote Line Deactivation LoopbackTelco-Initiated Remote Line Loopback Transferring Firmware and Configurations Using Tftp DSL1Transferring Firmware and Configurations Using Tftp Procedure Configuration Loader Main Menu → Configuration → Configuration LoaderCompleted successfully Transferring Firmware and Configurations Using Tftp May Configuration Options Select To Access To ConfigureNetwork Interface Options Menu Table A-1. Network Interface Options 1Port Status Margin ThresholdTable A-1. Network Interface Options 2 Excessive Error Rate ThresholdAutoRate Possible Settings 001.000.000.000 223.255.255.255, Clear Table A-1. Network Interface Options 3Transmit Attenuation Peer IP AddressDS0 Cross Connect Line Framing Table A-1. Network Interface Options 4Circuit Identifier Configuration Options Main Menu → Configuration → Current Configuration → DSX-1 DSX-1 Interface Options ModelTable A-4. DSX-1 Interface Options Model 8777 1 Line Coding FormatLine Framing Table A-4. DSX-1 Interface Options Model 8777 2Primary Clock Source Main Menu → Configuration → Current Configuration → G.703 Interface Options ModelTable A-5. G.703 Interface Options Model 8779 1 Interface OptionsFraming Table A-5. G.703 Interface Options Model 8779 2Line Coding Table A-5. G.703 Interface Options Model 8779 3 Primary Clock SourceCopy Ports Options Table A-6. Copy Port OptionsFrom Port n To Port yDSL Mode Test TimeoutSystem Options Table A-7. System Options 1Table A-7. System Options 2 Test Duration minTelco Initiated Loopback Remote Telco Line LoopbackSystem Clock System ClockFigure A-1. System Timing Figure A-2. System Clock Configuration Examples Table A-8. System Clock Options CROSS-CONNECT Configuration Cross-ConnectSetting Cross-Connect Mode Following screen is displayed for ModelMode DSL Table A-9. Cross-Connect Mode Options Model DSL PortTable A-10. Cross-Connect Mode Options Model SourceAssigning Time Slots Following screen is displayed for a DSX-1 port ModelTime Slot Number Assign Time Slots DSLTable A-11. Assign Time Slots Options 1 DSX-1/DSL or G.703/DSLPort Type PortTable A-11. Assign Time Slots Options 2 Start TSAssign To Data or VoiceTelnet Session Options Management and Communication Options MenuTelnet Session Options Table A-12. Telnet Session Options General Snmp Management Options Table A-13. General Snmp Management Options 1Snmp Management General Snmp Management OptionsName 1 Access Name 2 AccessTable A-13. General Snmp Management Options 2 Community NameSnmp NMS Security Options Snmp NMS Security OptionsNMS Table A-14. Snmp NMS Security Options Access TypeNMS IP Validation Snmp Traps Options Snmp Traps OptionsTable A-15. Snmp Traps Options 1 Snmp TrapsLink Traps Possible Settings Disable, Up, Down, Both Table A-15. Snmp Traps Options 2Enterprise Specific Traps Link Traps InterfacesInband Management Channel Inband Management Channel ModelPPP Table A-16. Inband Management Channel Options Model Configuring and Testing Inband Management Cross Connect Mode screen appears Cross Connect ModeFollowing screen appears = IbmcConfiguration Options Standards Compliance for Snmp Traps Snmp TrapsIfIndex IfIndex DescriptionAuthenticationFailure WarmStartLinkUp and linkDown Snmp Trap Description Possible CauseLinkUp/DownTvariable bindings Enterprise-Specific Traps IfType RFC 8700-A2-GB20-40 May May Connector Pin Assignments Front Panel 50-pin DTE Connector PinoutsConnector Pin Assignments Table C-2. Rear Connector Pinouts Connector Pins Port Tip, RingConnector Pin Assignments May Technical Specifications Technical Specifications May Using the Worksheets Cross-Connection WorksheetsPort Connection Diagram Time Slot Assignments DSX-1 Port DSX-1 Time Slot AssignmentsTS01 Time Slot Assignments DSX-1 Port Time Slot Assignments DSX-1 Port Time Slot Assignments DSX-1 Port Time Slot Assignments DSL Port Time Slot Assignments DSL PortTime Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments Time Slot Assignments G.703 PortTime Slot Assignments G.703 Port Time Slot Assignments G.703 Port Time Slot Assignments G.703 Port Time Slot Assignments G.703 Port Time Slot Assignments G.703 Port Time Slot Assignments G.703 Port Time Slot Assignments G.703 Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Time Slot Assignments DSL Port Index SnmpIN-2 IN-3 IN-4 IN-5 IN-6