Roland SC-88 Pro ❍MUTE (All Mute): On/Off, ●How each parameter works, ❍LEVEL (Master level): 0 —, ❍PAN (Master Pan): L63 — 0 — R63, ❍SC-55MAP (ALL SC-55MAP): On/Off

●How each parameter works

*The settings made here apply to all Parts (when the [ALL] indicator is lit). If you wish to make settings independently for each Part, use the procedure of p.25.

❍LEVEL (Master level): 0 — 127

This parameter adjusts the volume of all the Parts. As the displayed value increases, the volume will increase. The basic volume level of this entire unit is adjusted by the Volume knob. If the volume knob is at minimum position, there will be no sound even if you increase this parameter.

❍PAN (Master Pan): L63 — 0 — R63

This parameter sets the Pan (stereo position) for all the Parts. As the displayed L value increases the sound will move further left, and as the R value increases the sound will move further right.

*For some instruments, a bit of sound may be heard from the opposite speaker even if Pan has been set fully left or right.

*If you are listening to this unit in mono, Pan settings will have no effect.

❍KEY SHIFT (Master Key Shift): -24 — ± 0 — +24 semitone steps, 2 octaves

Key Shift adjusts the pitch of the sound in semitone steps. For example if you were playing back song data from a sequencer, you could use the Key Shift parameter to change the key of the song without changing the sequencer settings. Or, if you are singing along with sequence data, you can adjust Key Shift to move the song to the key most comfortable for your voice. As the displayed value rises (falls) one step, the pitch will rise (fall) one semitone. This means that 12 steps equal one octave.

*Even if you adjust Key Shift for all Parts, the pitch of the Drum Part will not be affected.

❍MUTE (All Mute): On/Off

If you press the [MUTE] button to turn the indicator on, All Mute will be on, and the sound of all Parts will be muted.

*Mute can also be set independently for each Part (p.25).

*When All Mute is turned on, each of the lowest dots in the bar display will be turned off.

1	2	3	4	5	6	7	8	9	10 11 12 13 14 15 16
1	2	3	4	5	6	7	8	9	10 11 12 13 14 15 16

❍SC-55 MAP (ALL SC-55 MAP): On/Off

If you press the [SC-55 MAP] button to make the indicator light, the sounds of all Parts will be set to the same sounds as the SC-55 map.

The [SC-55 MAP] button provides one-touch preparation for playing back SC-55/55mkII performance data.

*It is also possible to turn the SC-55 map on/off for indi- vidual Parts (p.25).

*All the sounds for all Parts can be arranged so they use the Native map by holding down [SELECT] while you press [SC-55 MAP] ( when the [ALL] indicator is lit ). At this time, [SC-55 MAP] indicator blinks.

❍SC-88 MAP (ALL SC-88 MAP): On/Off

If you press the [SC-88 MAP] button to make the indicator light, all Parts will have the same sound map structure as the SC-88.

Parts for which the SC-55 MAP is selected will be played using the sounds of the SC-55 map.

*It is also possible to turn the SC-88 map on/off for indi- vidual Parts.(p.25)

*When the [ALL] indicator is lit, you can hold down the [SELECT] button and press the [SC-88MAP] button to set all Parts to the SC-88 map. At this time, the [SC- 88MAP] indicator will blink.

			PART	INSTRUMENT
		ALL
			LEVEL	PAN
Set the sounds of		MUTE
Native map			REVERB	CHORUS
		SC-55
		MAP	KEY SHIFT	MIDI CH
		SC-88
		MAP
			DELAY
		VIB RATE	VIB DEPTH	VIB DELAY
USER			CUTOFF	RESONANCE
INST	SELECT	ATTACK	DECAY	RELEASE
EFX	ON/OFF	EFX TYPE	EFX PARAM	EFX VALUE

Set the sounds of SC-88 Map

Chapter 2. Parts and paramters 35