: small amp
: single-unit type amp
: large double stack amp
: large triple stack amp

<OD (Overdrive/Distortion)>

 

 

OD Sel (OD Select)

Odrv/Dist

[1]

Select either Overdrive or Distortion.

 

 

+OD Drive (OD Drive)

0 - 127

[2]

Adjust the depth of overdrive or distortion. The volume will change together with the depth of distor- tion.

OD Amp (OD Amp Simulator Type) Small/BltIn/2-Stk/3-Stk [3]

Select the type of guitar amp for overdrive or distor- tion.

Small

BltIn 2-Stk 3-Stk

OD Amp Sw (OD Amp Switch)

Off/On [4]

Turn the OD Amp parameter on/off.

OD Pan (OD Output Pan)

L63 - 0 - R63 [16]

Set the stereo location of the overdrive or distortion sound. L63 is far left, 0 is center, and R63 is far right.

OD Level (OD Level)

0 - 127 [17]

Adjust the volume of the overdrive or distortion sound.

<AW (Auto-wah)>

AW Filter (Auto-wah Filter Type)

LPF/BPF [6]

Select the type of filter for the auto-wah.

LPF : The wah effect will be produced over a broad frequency range.

BPF : The wah effect will be produced over

a narrow frequency range.

AW Sens (Auto-wah Sensitivity)

0 - 127 [7]

Adjust the sensitivity with which the auto-wah filter will be controlled.

#AW Man (Auto-wah Manual)

0 - 127 [8]

Set the center frequency at which the auto-wah effect will be produced.

AW Peak (Auto-wah Peak)

0 - 127 [9]

Adjust the way in which the wah effect will be applied to the region of the center frequency. Lower settings will produce a wah effect in a broad area around the center frequency, and higher settings will produce a wah effect in a narrower area around the center frequency.

AW Rate (Auto-wah Rate)

0.05 - 10.0 [10]

Adjust the modulation speed of the auto-wah.

AW Depth (Auto-wah Depth)

0 - 127 [11]

Adjust the modulation depth of the auto-wah.

AW Pol (Auto-wah Polarity)

Down/Up [12]

Set the direction in which the frequency will change when the auto-wah filter is modulated. With a setting of Up, the filter will change toward a higher fre- quency. With a setting of Down, it will change toward a lower frequency.

AW Pan (Auto-wah Output Pan)

L63 - 0 - R63 [18]

Adjust the stereo position of the auto-wah sound. L63 is far left, 0 is center, and R63 is far right.

AW Level (Auto-wah Level)

0 - 127 [19]

Adjust the volume of the auto-wah sound.

Level (Output level )

0 - 127 [20]

Adjust the output level.

 

 

 

63: PH / Rotary (Phaser, Rotary)

[11H, 07H]

This connects a Phaser effect in parallel with a Rotary effect.

Pan

LPhaser

RRotary

Pan

<PH (Phaser)>

PH Man (Phaser Manual)

100 - 8.0k [1]

Adjust the center frequency at which the sound will be modulated.

+PH Rate (Phaser Rate)

0.05 - 10.0 [2]

Adjust the modulation speed of the phaser.

PH Depth (Phaser Depth)

0 - 127 [3]

Adjust the modulation depth of the phaser.

PH Reso (Phaser Resonance)

0 - 127 [4]

Adjust the emphasis for the region around the center frequency specified by the PH Man parameter.

PH Mix (Phaser Mix Level)

0 - 127 [5]

Adjust the proportion of the phase-shifted sound that will be mixed with the direct sound.

PH Pan (Phaser Output Pan) L63 - 0 - R63 [16]

Set the stereo location of the phaser sound. L63 is far left, 0 is center, and R63 is far right.

PH Level (Phaser Level)

0 - 127 [17]

Adjust the volume of the phaser sound.

Chapter 4. Insertion Effects

89