Cutoff (Cutoff Frequency)

250 - 8 k [3]

Specify the cutoff frequency of the filter that is applied after the sound passes through the Lo-Fi effect.

+R.Detune (Radio Detune)

0 - 127 [4]

This simulates the tuning noise of a radio. As this value is raised, the tuning will drift further.

R.Nz Lev (Radio Noise Level)

0 - 127 [5]

Adjust the volume of the radio noise.

W/P Sel (White/Pink Noise Select) White/Pink [6]

Select either white noise or pink noise.

W/P LPF (White/Pink Noise LPF)

250 - 6.3 k/Bypass [7]

Specify the cutoff frequency of the low pass filter that is applied to the white noise or pink noise.

W/P Level (White/Pink Noise Level) 0 - 127 [8]

Specify the volume of the white noise or pink noise.

Disc Type (Disc Noise Type) LP/EP/SP/RND [9]

Select the type of record noise. The frequency at which the noise is heard will depend on the selected type.

Disc LPF (Disc Noise LPF)

250 - 6.3 k/Bypass [10]

Specify the cutoff frequency of the low pass filter that is applied to the record noise.

Disc Nz Lev (Disc Noise Level)

0 - 127 [11]

Specify the volume of the record noise.

Hum Type (Hum Noise Type)

50/60 Hz [12]

Select the type of hum noise.

Hum LPF (Hum Noise LPF)

250 - 6.3 k/Bypass [13]

Specify the cutoff frequency of the low pass filter that is applied to the hum noise.

Hum Level (Hum Noise Level)

0 - 127 [14]

Specify the volume of the hum noise.

M/S (Mono/Stereo Switch)

Mono/Stereo [15]

Select whether the effect sound will be monaural or

stereo.

 

#Balance (Effect Balance)

D> 0E - D 0 - 0<E [16]

Adjust the volume balance between the direct and the effect sound.

“D” or “E” on the display respectively means D(direct sound) or E(effect sound) values of 100.

Low Gain

-12 - +12 [17]

Adjust the gain of the low frequency range.

Hi Gain (High gain)

-12 - +12 [18]

Adjust the gain of the high frequency range.

Pan (Mono) (Output Pan (Mono))

L63 - 0 - R63 [19]

When Mono mode is used, adjust the stereo location of the output sound. L63 is far left, 0 is center, and R63 is far right.

Level (Output level)

0 - 127 [20]

Adjust the output level.

❍Effects that connect two types of effect in series (series 2)

35: OD → Chorus (Overdrive → Chorus)

[02H, 00H]

This effect connects an overdrive and a chorus in series.

L

 

EQ

Overdrive

Chorus

Balance

R

 

EQ

OD Drive (Overdrive drive )

0 - 127 [1]

Adjust the degree of overdrive distortion. The volume will change together with the degree of distor- tion.

+OD Pan (Overdrive drive output pan )

L63 - 0 - R63 [2]

Adjust the stereo location of the overdrive sound. L63 is far left, 0 is center, and R63 is far right.

OD Amp (Overdrive Amp Simulator Type)

 

Small/BltIn/2-Stk/3-Stk [3]

Select the type of guitar amp.

 

Small

: small amp

 

BltIn

: single-unit type amp

 

2-Stk

: large double stack amp

 

3-Stk

: large triple stack amp

 

OD Amp Sw (Overdrive Amp switch)

Off/On [4]

Turn OD Amp on/off.

 

Cho Dly (Chorus pre delay )

0 - 100m [6]

Adjust the time delay from when the direct sound begins until the chorus sound is heard.

Cho Rate (Chorus rate )

0.05 - 10.0 [7]

Adjust the modulation speed of the chorus effect.

Cho Depth (Chorus depth )

0 - 127 [8]

Adjust the modulation depth of the chorus effect.

#Cho Bal (Chorus balance ) D> 0E - D 0<E [10]

Adjust the volume balance between the sound which passes through the chorus and the sound which does not. With a setting of D>0E, only the overdrive sound will be output, and with a setting of D 0<E, the overdrive sound which passes through the chorus will be output. “D” and “E” respectively indicate D (dry sound) and E (effect sound) values of 100.

Low Gain

-12 - +12 [17]

Adjust the low frequency gain.

 

Hi Gain (High gain )

-12 - +12 [18]

Adjust the high frequency gain.

 

Chapter 4. Insertion Effects

71