Roland SC-88 Pro manual 90

RT H Slow (RT High Frequency Slow Rate)

0.05 - 10.0 [10]

Adjust the speed of the high-range rotor for the low- speed (Slow) setting.

RT H Fast (RT High Frequency Fast Rate)

0.05 - 10.0 [11]

Adjust the speed of the high-range rotor for the high-speed (Fast) setting.

RT Hi Accl (RT High Frequency Acceleration)

0 - 15 [12]

Adjust the time over which the rotation speed of the high-range rotor will change from low-speed to high-speed (or high-speed to low-speed) rotation. Smaller values will require greater time to reach the new rotational speed.

RT Hi Lev (RT High Frequency Level)

0 - 127 [13]

Adjust the volume of the high-range rotor.

RT Sept (RT Separation) 0 - 127 [14]

Adjust the spatial spread of the rotary sound.

#RT Speed Slow/Fast [15]

Simultaneously switch the rotational speed of both the low-range and the high-range rotors.

Slow : Slow down the rotation to the specified speeds (RT L Slow parameter / RT H Slow parameter values).

Fast : Speed up the rotation to the specified speeds (RT L Fast parameter / RT H Fast parameter values).

RT Pan (RT Output Pan) L63 - 0 - R63 [18]

Adjust the stereo position of the rotary sound. L63 is far left, 0 is center, and R63 is far right.

RT Level 0 - 127 [19]

Adjust the volume of the rotary sound.

Level (Output level ) 0 - 127 [20]

Adjust the output level.

61:OD / Phaser(Overdrive/Distortion, Phaser) [11H, 05H]

This connects an overdrive or distortion in parallel with a phaser.

Pan

LOverdrive/ Distortion

RPhaser

Pan

<OD (Overdrive/Distortion)>

OD Sel (OD Select) Odrv/Dist [1]

Select either Overdrive or Distortion.

+OD Drive (OD Drive) 0 - 127 [2]

Adjust the depth of distortion. The volume will change together with the depth of distortion.

OD Amp (OD Amp Simulator Type)

Smal/BltIn/ 2-Stk/3-Stk [3]

Select the type of guitar amp.

Small : small amp

BltIn : single-unit type amp

2-Stk : large double stack amp

3-Stk : large triple stack amp

OD Amp Sw (OD Amp Switch)	Off/On [4]
Turn the OD Amp parameter on/off.
OD Pan (OD Output Pan)	L63 - 0 - R63 [16]

Set the stereo location of the overdrive or distortion sound. L63 is far left, 0 is center, and R63 is far right.

OD Level	0 - 127 [17]
Adjust the overdrive or distortion volume.
<PH (Phaser)>
PH Man (Phaser Manual)	100 - 8.0k [6]
Adjust the center frequency at which the sound will
be modulated.
#PH Rate (Phaser Rate)	0.05 - 10.0	[7]
Adjust the modulation speed.
PH Depth (Phaser Depth)	0 - 127	[8]
Adjust the modulation depth.
PH Reso (Phaser Resonance)	0 - 127	[9]

Adjust the emphasis for the region around the center frequency specified by the PH Man parameter.

PH Mix (Phaser Mix Level) 0 - 127 [10]

Adjust the proportion of the phase-shifted sound that will be mixed with the direct sound.

PH Pan (Phaser Output Pan) L63 - 0 - R63 [18]

Set the stereo location of the phaser sound. L63 is far left, 0 is center, and R63 is far right.

PH Level 0 - 127 [19]

Adjust the volume of the phaser sound.

Level (Output level ) 0 - 127 [20]

Adjust the output level.

62:OD / AutoWah (Overdrive/Distortion, Auto-wah) [11H, 06H]

This connects an Overdrive or Distortion in parallel with an Auto-wah.

Pan

LOverdrive/ Distortion

R Auto Wah

Pan

88 Chapter 4. Insertion Effects