#Dly Bal (Delay balance )

D> 0E - D 0<E [10]

Adjust the volume balance between the direct and the delay sound.

D” or “E” on the display respectively means D(direct sound) or E(effect sound) values of 100.

Dly Pan (Delay Output Pan) L63 - 0 - R63 [18]

Adjust the stereo position of the delay sound. L63 is far left, 0 is center, and R63 is far right.

Dly Level (Delay Level)

0 - 127 [19]

Adjust the volume of the delay sound.

Level (Output level )

0 - 127 [20]

Adjust the output level.

 

 

 

58: Cho / Flanger (Chorus / Flanger)

[11H, 02H]

This effect connects a chorus and a flanger in parallel.

Pan

L

Chorus

Balance

Flanger

R

Pan

Cho Dly (Chorus pre delay )

0 - 100m [1]

Adjust the time delay from when the direct sound begins until the chorus sound is heard.

Cho Rate (Chorus rate )

0.05 - 10.0 [2]

Adjust the modulation speed of the chorus effect.

Cho Depth (Chorus depth )

0 - 127 [3]

Adjust the modulation depth of the chorus effect.

+Cho Bal (Chorus balance ) D> 0E - D 0<E [5]

Adjust the volume balance between the direct and the chorus sound.

D” or “E” on the display respectively means D(direct sound) or E(effect sound) values of 100.

Cho Pan (Chorus Output Pan) L63 - 0 - R63 [16]

Adjust the stereo position of the chorus sound. L63 is far left, 0 is center, and R63 is far right.

Cho Level (Chorus Level)

0 - 127 [17]

Adjust the volume of the chorus sound.

FL Dly (Flanger pre delay )

0 - 100m [6]

Adjust the time delay from when the direct sound begins until the flanger sound is heard.

FL Rate (Flanger rate )

0.05 - 10.0 [7]

Adjust the modulation speed of the flanger effect.

FL Depth (Flanger depth )

0 - 127 [8]

Adjust the modulation depth of the flanger effect.

FL Fb (Flanger feedback level ) -98% - +98% [9]

Adjust the proportion (%) of the flanger sound that is fed back into the effect. Negative (-) settings will invert the phase.

#FL Bal (Flanger balance ) D> 0E - D 0<E [10]

Adjust the volume balance between the direct and the flanger sound.

D” or “E” on the display respectively means D(direct sound) or E(effect sound) values of 100.

FL Pan (Flanger Output Pan) L63 - 0 - R63 [18]

Adjust the stereo position of the flanger sound. L63 is far left, 0 is center, and R63 is far right.

FL Level (Flanger Level)

0 - 127 [19]

Adjust the volume of the flanger sound.

Level (Output level )

0 - 127 [20]

Adjust the output level.

59: OD1 / OD2 (Overdrive / Distortion1,2) [11H, 03H]

This connects two effect units in parallel, each of which allows you to select Overdrive or Distortion.

Pan

LOverdrive/ Distortion 1

ROverdrive/ Distortion 2

Pan

<OD1 (Overdrive/Distortion 1)>

OD1 Sel (OD1 Select)

Odrv/Dist [1]

Select either Overdrive or Distortion for set 1.

+OD1 Drive (OD1 Drive)

0 - 127 [2]

Adjust the depth of distortion for set 1. The volume will change together with the depth of distortion.

OD1 Amp (OD1 Amp Simulator Type) Small/BltIn/2-Stk/3-Stk [3]

Select the type of guitar amp for set 1.

Small : small amp

BltIn : single-unit type amp

2-Stk : large double stack amp

3-Stk : large triple stack amp

86

Chapter 4. Insertion Effects