Roland SC-88 Pro manual 76

#FL Bal (Flanger balance) D> 0E - D 0<E [10]

Adjust the volume balance between the sound which passes through the flanger and the sound which does not. With a setting of D>0E, only the distortion sound will be output, and with a setting of D 0<E, the distortion sound which passes through the flanger will be output.

“D” or “E” on the display respectively means D(direct sound) or E(effect sound) values of 100.

Low Gain	-12	- +12 [17]
Adjust the low frequency gain.
Hi Gain (High gain )	-12	- +12 [18]
Adjust the high frequency gain.
Level (Output level )	0	- 127 [20]
Adjust the output level.
40: DS → Delay (Distortion →	Delay ) [02H, 05H]

This effect connects a distortion and a delay in series.

L		EQ
Distortion	Delay	Balance
R		EQ

DS Drive (Distortion drive )	0 - 127	[1]
Adjust the degree of distortion. The volume will
change together with the degree of distortion.
+DS Pan (Distortion output pan )
	L63 - 0 - R63	[2]

Adjust the stereo location of the distortion sound. L63 is far left, 0 is center, and R63 is far right.

DS Amp (Distortion Amp Simulator Type)

	Small/BltIn/2-Stk/3-Stk [3]
Select the type of guitar amp.
Small	: small amp
BltIn	: single-unit type amp
2-Stk	: large double stack amp
3-Stk	: large triple stack amp
DS Amp Sw (Distortion Amp Switch)		Off/On [4]
Turn DS Amp on/off.
Dly Time (Delay time )		0 - 500m [6]

Adjust the time delay from when the direct sound begins until the delay sound is heard.

Dly Fb (Delay feedback level ) -98% - +98% [7]

Adjust the proportion (%) of the delay sound that is fed back into the effect. Negative (-) settings will invert the phase.

Dly HF (Delay HF damp ) 315 - 8k/Bypass [8]

Adjust the frequency above which delayed sound fed back to the effect will be cut. If you do not wish to cut the high frequencies of the feedback, set this parameter to Bypass.

#Dly Bal (Delay balance ) D> 0E - D 0<E [10]

Adjust the volume balance between the sound which passes through the delay and the sound which does not. With a setting of D>0E, only the distortion sound will be output, and with a setting of D 0<E, the distortion sound which passes through the delay will be output. “D” and “E” respectively indicate D (dry sound) and E (effect sound) values of 100.

Low Gain	-12 - +12	[17]
Adjust the low frequency gain.
Hi Gain (High gain )	-12 - +12	[18]
Adjust the high frequency gain.
Level (Output level )	0 - 127	[20]
Adjust the output level.
41: EH → Chorus (Enhancer →	Chorus)
	[02H, 06H]

This effect connects an enhancer and a chorus in series.

L	Enhancer	EQ
	Chorus	Balance
R	Enhancer	EQ

+EH Sens (Enhancer Sensitivity )	0 - 127 [1]
Adjust the sensitivity of the enhancer.
EH Mix (Enhancer Mix level )	0 - 127 [2]

Adjust the ratio with which the overtones generated by the enhancer are combined with the direct sound.

Cho Dly (Chorus pre delay ) 0 - 100m [6]

Adjust the time delay from when the direct sound begins until the chorus sound is heard.

Cho Rate (Chorus rate ) 0.05 - 10.0 [7]

Adjust the modulation speed of the chorus effect.

Cho Depth (Chorus depth ) 0 - 127 [8]

Adjust the modulation depth of the chorus effect.

#Cho Bal (Chorus balance ) D> 0E - D 0<E [10]

Adjust the volume balance between the sound which passes through the chorus and the sound which does not. With a setting of D>0E, only the enhancer sound will be output, and with a setting of D 0<E, the enhancer sound which passes through the chorus will be output.

“D” or “E” on the display respectively means D(direct sound) or E(effect sound) values of 100.

Low Gain -12 - +12 [17]

Adjust the low frequency gain.

74 Chapter 4. Insertion Effects