Roland SC-88 Pro manual 84

CF Depth	0 - 127	[14]
Adjust the depth of modulation for the chorus or
flanger.
CF Fb (CF Feedback)	-98% - +98%	[15]

Adjust the amount (%) of the flanger sound that will be returned to the input. Negative (-) values will invert the phase.

In the case of Chorus, this will have no effect.

CF Mix 0 - 127 [16]

Adjust the volume of the chorus or flanger sound.

<Dly (Delay)>

Dly Time (Delay Time) 0m - 635m [17]

Adjust the time from the original sound until when the delay sound is heard.

Dly Fb (Delay Feedback Level) 0 - 127 [18]

Adjust the amount of the delay sound that is returned to the input.

#Dly Mix (Delay Mix) 0 - 127 [19]

Adjust the volume of the delay sound.

Level (Output level )	0 - 127 [20]
Adjust the output level.
53: Bass Multi	[04H, 05H]

Bass Multi provides Compressor (Cmp), Overdrive or Distortion (OD), Equalizer (EQ), and Chorus or Flanger (CF) effects connected in series.

L
	Cmp	OD	EQ	CF
R
<Cmp (Compressor)>
Cmp Atck (Compressor Attack)				0 - 127 [1]
Adjust the time over which the sound will rise after it
is input.
Cmp Sus (Compressor Sustain)				0 - 127 [2]

Adjust the time over which low-level sounds are boosted until they reach a specified volume.

Increasing the value will shorten the time. When the value is modified, the level will also change.

Cmp Level (Compressor Level) 0 - 127 [3]

Adjust the volume of the compressor sound.

Cmp Sw (Compressor Switch) Off/On [4]

Turn the compressor on/off.

<OD (Overdrive/Distortion)>

OD Sel (ODSelect) Odrv/Dist [5]

Select either bass guitar Overdrive or Distortion.

+OD Drive (OD Drive) 0 - 127 [6]

Adjust the depth of distortion. The volume will change together with the depth of distortion.

OD Amp (OD Amp Simlation Type) Small/BltIn/2-Stk [7]

Select the type of guitar amp

Small : small amp

BltIn : single-unit type amp

2-Stk : large double stack amp

OD Amp Sw (OD Amp Switch)	Off/On [8]
Turn OD Amp on/off.
OD Sw (OD Switch)	Off/On [9]
Turn Overdrive/Distortion on/off.
<EQ (Equalizer)>
EQ L Gain (EQ Low Gain)	-12 - +12 [10]

Adjust the low-range gain of the equalizer.

EQ M Fq (EQ Mid Frequency)		200 - 6.3k	[11]
Set the center frequency for the equalizer mid-
range.
EQ M Q (EQ Mid Q)	0.5/1.0/2.0/4.0/9.0		[12]

Adjust the width of the area centered at the EQ M Fq setting in which the gain will be affected. The area affected will become narrower as this value is increased.

EQ M Gain (EQ Mid Gain) -12 - +12 [13]

Adjust the gain of the area specified by the EQ M Fq parameter and the EQ M Q parameter.

EQ H Gain (EQ High Gain) -12 - +12 [14]

Adjust the high-range gain of the equalizer.

<CF(Chorus/Flanger)>
CF Sel (CF Select)	Chorus/Flangr [15]
Select either Chorus or Flanger.
CF Rate	0.05 - 6.40 [16]

Adjust the speed of modulation for the chorus or flanger.

CF Depth 0 - 127 [17]

Adjust the depth of modulation for the chorus or flanger.

CF Fb (CF Feedback level) -98% - +98% [18]

Adjust the amount (%) of the flanger sound that will be returned to the input. Negative (-) values will invert the phase.

In the case of Chorus, this will have no effect.

82 Chapter 4. Insertion Effects