Roland SC-88 Pro manual 92

<RT (Rotary)>

RT L Slow (RT Low Frequency Slow Rate)

0.05 - 10.0 [6]

Adjust the speed of the low-range rotor for the low- speed (Slow) setting.

RT L Fast (RT Low Frequency Fast Rate)

0.05 - 10.0 [7]

Adjust the speed of the low-range rotor for the high- speed (Fast) setting.

RT Lo Accl (RT Low Frequency Acceleration)

0 - 15 [8]

Adjust the time over which the rotation speed of the low-range rotor will change from low-speed to high- speed (or high-speed to low-speed) rotation. Smaller values will require greater time to reach the new rotational speed.

RT Lo Lev (RT Low Frequency Level) 0 - 127 [9]

Adjust the volume of the low-range rotor.

RT H Slow (RT High Frequency Slow Rate)

0.05 - 10.0 [10]

Adjust the speed of the high-range rotor for the low- speed (Slow) setting.

RT H Fast (RT High Frequency Fast Rate)

0.05 - 10.0 [11]

Adjust the speed of the high-range rotor for the high-speed (Fast) setting.

RT Hi Accl (RT High Frequency Acceleration)

0 - 15 [12]

Adjust the time over which the rotation speed of the high-range rotor will change from low-speed to high-speed (or high-speed to low-speed) rotation. Smaller values will require greater time to reach the new rotational speed.

RT Hi Lev (RT High Frequency Level)

0 - 127 [13]

Adjust the volume of the high-range rotor.

RT Sept (RT Separation) 0 - 127 [14]

Adjust the spread of the rotary sound.

#RT Speed Slow/Fast [15]

Simultaneously switch the rotational speed of both the low-range and the high-range rotors.

Slow : Slow down the rotation to the specified speeds (RT L Slow parameter / RT H Slow parameter values).

Fast : Speed up the rotation to the specified speeds (RT L Fast parameter / RT H Fast parameter values).

RT Pan (RT Output Pan) L63 - 0 - R63 [18]

Adjust the stereo position of the rotary sound. L63 is far left, 0 is center, and R63 is far right.

RT Level 0 - 127 [19]

Adjust the volume of the rotary sound.

Level (Output level ) 0 - 127 [20]

Adjust the output level.

64: PH / AutoWah (Phaser, Auto-wah)

[11H, 08H]

This connects a Phaser effect and an Auto-wah effect in parallel.

Pan

LPhaser

RAuto Wah

Pan

<PH (Phaser)>

PH Man (Phaser Manual) 100 - 8.0k [1]

Adjust the center frequency at which the phaser sound will be modulated.

+PH Rate (Phaser Rate) 0.05 - 10.0 [2]

Adjust the modulation speed of the phaser.

PH Depth (Phaser Depth) 0 - 127 [3]

Adjust the modulation depth of the phaser.

PH Reso (Phaser Resonance) 0 - 127 [4]

Adjust the emphasis for the region around the center frequency specified by the PH Man parameter.

PH Mix (Phaser Mix Level) 0 - 127 [5]

Adjust the proportion of the phase-shifted sound that will be mixed with the direct sound.

PH Pan (Phaser Output Pan) L63 - 0 - R63 [16]

Set the stereo location of the phaser sound. L63 is far left, 0 is center, and R63 is far right.

PH Level (Phaser Level) 0 - 127 [17]

Adjust the volume of the phaser sound.

<AW (Auto-wah)>

AW Filter (Auto-wah Filter Type) LPF/BPF [6]

Select the type of filter for the auto-wah.

LPF : The wah effect will be produced over a broad frequency range.

BPF : The wah effect will be produced over

a narrow frequency range.

AW Sens (Auto-wah Sensitivity) 0 - 127 [7]

Adjust the sensitivity with which the auto-wah filter will be modulated.

90 Chapter 4. Insertion Effects