Roland SC-88 Pro manual 75

Low Gain	-12 - +12	[17]
Adjust the low frequency gain.
Hi Gain (High gain )	-12 - +12	[18]
Adjust the high frequency gain.
Level (Output level )	0 - 127	[20]
Adjust the output level.
38: DS → Chorus (Distortion →	Chorus)
	[02H, 03H]

This effect connects a distortion and a chorus in series.

L		EQ
Distortion	Chorus	Balance
R		EQ
DS Drive (Distortion drive )		0 - 127 [1]

Adjust the degree of distortion. The volume will change together with the degree of distortion.

+DS Pan (Distortion output pan )

L63 - 0 - R63 [2]

Adjust the stereo location of the distortion sound. L63 is far left, 0 is center, and R63 is far right.

DS Amp (Distortion Amp Simulator Type)

	Small/BltIn/2-Stk/3-Stk [3]
Select the type of guitar amp.
Small	: small amp
BltIn	: single-unit type amp
2-Stk	: large double stack amp
3-Stk	: large triple stack amp
DS Amp Sw (Distortion Amp Switch)		Off/On [4]
Turn DS Amp on/off.
Cho Dly (Chorus pre delay )		0 - 100m [6]

Adjust the time delay from when the direct sound begins until the chorus sound is heard.

Cho Rate (Chorus rate ) 0.05 - 10.0 [7]

Adjust the modulation speed of the chorus effect.

Cho Depth (Chorus depth ) 0 - 127 [8]

Adjust the modulation depth of the chorus effect.

#Cho Bal (Chorus balance ) D> 0E - D 0<E [10]

Adjust the volume balance between the sound which passes through the chorus and the sound which does not. With a setting of D>0E, only the distortion sound will be output, and with a setting of D 0<E, the distortion sound which passes through the chorus will be output.

“D” or “E” on the display respectively means D(direct sound) or E(effect sound) values of 100.

Low Gain	-12	- +12	[17]
Adjust the low frequency gain.
Hi Gain (High gain )	-12	- +12	[18]
Adjust the high frequency gain.
Level (Output level )	0	- 127	[20]
Adjust the output level.
39: DS → Flanger (Distortion →	Flanger)
	[02H, 04H]

This effect connects a distortion and a flanger in series.

L		EQ
Distortion	Flanger	Balance
R		EQ
DS Drive (Distortion drive )		0 - 127 [1]

Adjust the degree of distortion. The volume will change together with the degree of distortion.

+DS Pan (Distortion output pan )

L63 - 0 - R63 [2]

Adjust the stereo location of the distortion sound. L63 is far left, 0 is center, and R63 is far right.

DS Amp (Distortion Amp Simulator Type)

	Small/BltIn/2-Stk/3-Stk [3]
Select the type of guitar amp.
Small	: small amp
BltIn	: single-unit type amp
2-Stk	: large double stack amp
3-Stk	: large triple stack amp
DS Amp Sw (Distortion Amp Switch)		Off/On [4]
Turn DS Amp on/off.
FL Dly (Flanger pre delay )		0 - 100m [6]

Adjust the time delay from when the direct sound begins until the flanger sound is heard.

FL Rate (Flanger rate ) 0.05 - 10.0 [7]

Adjust the modulation speed of the flanger effect.

FL Depth (Flanger depth ) 0 - 127 [8]

Adjust the modulation depth of the flanger effect.

FL Fb (Flanger feedback level ) -98% - +98% [9]

Adjust the proportion (%) of the flanger sound that is fed back into the effect. Negative (-) settings will invert the phase.

Chapter 4. Insertion Effects 73