TDK 750W HALF RACK technical manual Chapter, Specifications

CHAPTER 2			SPECIFICATIONS
	2.1 OUTPUT RATING
	MODEL			GEN	6-100		8-90	12.5-60		20-38		30-25	40-19		–	60-12.5	80-9.5	100-7.5	150-5	300-2.5	600-1.3
	1.Rated output voltage (*1)			V	6		8	12.5		20		30	40		–	60	80	100	150	300	600
	2.Rated output current 750W (*2)			A	100		90	60		38		25	19		–	12.5	8.5	7.5	5	2.5	1.3
	3.Rated output power 750W			W	600		720	750		760		750	760		–	750	760	750	750	750	780
	MODEL			GEN	6-200		8-180	12.5-120		20-76		30-50	40-38		50-30	60-25	80-19	100-15	150-10	300-5	600-2.6
	1.Rated output voltage (*1)			V	6		8	12.5		20		30	40		50	60	80	100	150	300	600
	2.Rated Output Current 1500W (*2)			A	200		180	120		76		50	38		30	25	19	15	10	5	2.6
	3.Rated output power 1500W			W	1200		1440	1500		1520		1500	1520		1500	1500	1520	1500	1500	1500	1560
	2.2 INPUT CHARACTERISTICS
				V	6		8	12.5		20		30	40		50	60	80	100	150	300	600
	1.	Input voltage/freq. (*3)		–	85~265Vac	continuous,		47-63Hz, single phase.
	2.	Input current (at 100/200Vac)		A	10.5/5 for 750W model, 21/11 for 1500W models.
	3.	Power Factor		–	0.99@100/200Vac, rated output power.
	4.	750W models Efficiency (*4)		%	76/78		77/80	81/84		82/85		82/85	83/87		83/87	83/87	83/87	83/87	83/87	83/87	83/87
	5.	1500W models Efficiency (*4)		%	77/79		78/81	82/85		83/86		83/86	84/88		84/88	84/88	84/88	84/88	84/88	84/88	84/88
	6.	Inrush current at 100/200V		A	Less than	25A for 750W models, 50A for 1500W models.
	2.3 CONSTANT VOLTAGE MODE
				V	6		8	12.5		20		30	40		50	60	80	100	150	300	600
	1.	Max.Line regulation (*5)		–	0.01% of	rated output		voltage +2mV
	2.	Max.Load regulation (*6)		–	0.01% of rated output voltage +2mV
	3.	Ripple and noise (p-p,20MHz) (*10)		mV	60		60	60		60		60	60		60	60	80	80	100	150	300
	4.	Ripple r.m.s., 5Hz~1MHz (*10)		mV	8		8	8		8		8	8		8	8	8	8	10	25	60
	5.	Temperature coefficient		PPM/°C	100PPM/°C	of rated output voltage, following 30 min utes warm up
	6.	Temperature drift		–	0.05% of rated Vout over 8hrs interval following 30 minutes warm-up. Constant line, load & temp.
	7.	Rem. Sense compensation/wire		V	1		1	1		1		1.5	2		2	3	4	5	5	5	5
	8.	Up-prog. Response time 0~Vomax (*9)		mS						80								150			250
	9.	Down-prog. Response time: Full load		mS	10			50						80				150			250
			No load		500		600	700		800		900	1000		1100	1100	1200	1500	2000	2500	4000
	10. Transient response time			mS	Time for the output voltage to recover within 0.5% of its rated output for a load change 10~90% of rated
					output current.
					Output set-point: 10~100%.
					Less than 1mS for models up to and including 100V; 2mS for models above 100V.
	11. Hold-up time			mS	More than 20mS, 100Vac, rated output power.
	2.4 CONSTANT CURRENT MODE
				V	6		8	12.5		20		30	40		50	60	80	100	150	300	600
	1.	Max.line regulation (*5)		–	0.01% of	rated output		voltage +2mA
	2.	Max.load regulation (*7)		–	0.02% of rated output current +5mA
	3.	Ripple r.m.s. 5Hz~1MHz.750W (*8)		mA	200		180	120		76		63	48		–	38	29	23	18	13	8
		1500W (*8)		mA	400		360	240		152		125	95		75	75	57	45	35	25	12
	4.	Temperature coefficient		PPM/°C	100PPM/°C	from rated		output current,	following		30 m inutes		warm-up.
	5.	Temperature drift		–	0.05% of rated lout over 8hrs interval following 30 minutes warm-up. Constant line, load & temp.
	2.5 ANALOG PROGRAMMING AND MONITORING
	1.Vout voltage programming			–	0~100%, 0~5V or 0~10V, user select. Accuracy and linearity; +/-0.5% of rated Vout.
	2.	Iout voltage programming		–	0~100%, 0~5V or 0~10V, user select. Accuracy and linearity; +/-1% of rated Iout.
	3.	Vout resistor progrmming		–	0~100%, 0~5/10Kohm full scale, user select. Accuracy and linearity: +/-1% of rated Vout.
	4.	Iout resistor programming		–	0~100%, 0~5/10Kohm full scale, user select. Accuracy and linearity: +/-1.5% of rated Iout.
	5.	On/off control		–	By electrical Voltage: 0~0.6V/2~15V or dry contact, user selectable logic.
	6.	Output current monitor		–	0~5V or 0~10V, user selectable. Accuracy: 1%
	7.	Output voltage monitor		–	0~5V or 0~10V, user selectable. Accuracy: 1%
	8.	Power supply OK signal		–	4~5V-OK, 0V-Fail, 500ohm series resistance.
	9.	Parallel operation		–	Possible, up to 4 units in master/slave mode with single wire current balance connection.
	10. Series operation			–	Possible (with external diodes), up to 2 units.
	11. CV/CC inicator			–	CV: TTL high (4~5V), source current: 10mA, CC: TTL low (0-0.6V). Sink current: 10mA .
	12. Enable/Disable			–	Dry contact. Open: off, Short: on. Max. voltage at Enable/Disable in: 6V.
	13. Local/Remote analog control			–	By electrical signal or Open/Short: 0~0.6V or short: Remote, 4~5V or open: Local.
	14. Local/remote analog indicator			–	Open collector. Local: Open, Remote: On. Maximum voltage: 30V, maximum sink current: 5mA.

9

83-507-5002 Rev. B