TABLE OF CONTENTS
5.15 PARALLEL OPERATION………………………………………………………….…………. | …. | Pg. 41 | |||
5.15.1 Basic parallel operation……………………………………………………………………. |
|
| Pg. 41 | ||
5.15.2 Advanced parallel operation…………………………… | …………………………………. |
| Pg. 42 | ||
5.16 |
| Pg. 44 | |||
5.17 FRONT PANEL LOCKING……………………………………………………………………… |
| . | Pg. 44 | ||
5.17.1 Unlocked front panel……………………………………………… | ………………………. |
| Pg. 45 | ||
5.17.2 Locked front panel…………………………………………………… | … …………………. |
| Pg. 45 | ||
CHAPTER 6 REMOTE ANALOG PROGRAMMING……………………………………… |
| ……… |
| Pg. 46 | |
6.1 INTRODUCTION…………………………………………………………………………………… |
|
| Pg. 46 | ||
6.2 LOCAL/REMOTE ANALOG CONTROL…………………………………………………… | …… | Pg. 46 | |||
6.3 LOCAL/REMOTE ANALOG INDICATION…………………………………………… | ……… …. | Pg. 46 | |||
6.4 REMOTE VOLTAGE PROGRAMMING OF OUTPUT VOLTAGE AND CURRENT LIMIT | Pg. 47 | ||||
6.5 RESISTIVE PROGRAMMING OF OUTPUT VOLTAGE AND CURRENT………………….. |
| Pg. 48 | |||
6.6 REMOTE MONITORING OF OUTPUT VOLTAGE AND CURRENT………………………... |
| Pg. 49 | |||
CHAPTER 7 RS232 & RS485 REMOTE CONTROL……………………………………………... |
| Pg. 50 | |||
7.1 INTRODUCTION…………………………………………………………………………………… |
|
| Pg. 50 | ||
7.2 CONFIGURATION…………………………………………………………………………………. |
|
| Pg. 50 | ||
7.2.1 Default setting………………………………………………………………………………... |
|
| Pg. 50 | ||
7.2.2 Address setting………………………………………………………………………………. |
|
| Pg. 50 | ||
7.2.3 RS232 or RS485 selection…………………………………………………………………. |
|
| Pg. 50 | ||
7.2.4 Baud rate setting………………………………………………………… | ………………….. |
| Pg. 50 | ||
7.2.5 Setting the unit into Remote or Local mode………………………………………………. |
| Pg. 50 | |||
7.2.6 RS232/458 port at Local mode…………………………… | ……………………………….. |
| Pg. 51 | ||
7.2.7 Front panel in Remote mode………………………………… | ……………………………. |
| Pg. 51 | ||
7.3 REAR PANEL RS232/485 CONNECTOR…………………………………………… | …………. | Pg. 51 | |||
7.4 MD MODE OPTION (Factory Installed)…………………………………………………………. |
| Pg. 52 | |||
7.4.1 MD Mode Description…………………………………………………… | ………………….. |
| Pg. 52 | ||
7.4.2 MD Mode enable - Serial communication mode…………………………………………. |
| Pg. 52 | |||
7.4.3 MD Mode SRQ………………………………………………………………………… | ……. | Pg. 52 | |||
7.4.4 Communication Collisions………………………………………………………………….. |
|
| Pg. 52 | ||
7.4.5 MD Mode SRQ Retransmission………………………………… | ………………………… |
| Pg. 52 | ||
7.5 CONNECTING POWER SUPPLIES TO RS232 OR RS485 BUS……………………………. |
| Pg. 53 | |||
7.5.1 Single power supply…………………………………………………… | ……… ……………. |
| Pg. 53 | ||
7.5.2 Multi power supply connection to RS232 or RS485 BUS……………………………….. |
| Pg. 54 | |||
7.6 COMMUNICATION INTERFACE PROTOCOL……………………………………… | ………… | Pg. 54 | |||
7.6.1 Data format…………………………………………………………………………………... |
|
| Pg. 54 | ||
7.6.2 Addressing……… …………………………………………………………………………… |
|
| Pg. 54 | ||
7.6.3 End of message………………………………………………………………… | ………….. |
| Pg. 54 | ||
7.6.4 Command repeat………………………………………………………………… | …………. | Pg. 54 | |||
7.6.5 Checksum………………………………………………………………………………… | …. | Pg. 54 | |||
7.6.6 Acknowledge…… ……………………………………………………………………………. |
|
| Pg. 54 | ||
7.6.7 Error message…………………………………………………………………… | ………….. | Pg. 55 | |||
7.6.8 Backspace……………………………………………………………………………… | ……. | Pg. 55 | |||
7.7 ERROR MESSAGES……………………………………………………………………………… |
|
| Pg. 55 | ||
7.8 COMMAND SET DESCRIPTION………… ……………………………………………………… |
| Pg. 55 | |||
7.8.1 General guide.………………………………………………………………… | ………….…. |
| Pg. 55 | ||
7.8.2 Command set categories…………………………………………………………………… |
|
| Pg. 55 | ||
7.8.3 Initialization control commands…………………… ……………………………………….. |
| Pg. 56 | |||
7.8.4 ID control commands……………………………………………………………………….. |
|
| Pg. 56 | ||
7.8.5 Output control commands………………………………………… | ……………………….. |
| Pg. 56 | ||
7.9 GLOBAL OUTPUT COMMANDS………………………………………………………………… |
| Pg. 58 | |||
7.9.1 General…………………………………………………………………………………… | ….. | Pg. 58 | |||
7.10 SINGLE BYTE COMMANDS……………………………………………………………………. |
|
| Pg. 59 | ||
7.10.1 General……………………………………………………………………………………… |
|
| Pg. 59 | ||
7.10.2 Global commands without response……………… | …………………………………….. |
| Pg. 59 | ||
7.10.3 Global commands with response……………………… | ……………………………… | … | Pg. 60 | ||
