Supplemental Characteristics | TDK 750W HALF RACK guide

NOTES:

*1: Minimum voltage is guaranteed to maximum 0.2% of the rated output voltage.

*2: Minimum current is guaranteed to maximum 0.4% of the rated output current.

*3: For cases where conformance to various safety standards (UL, IEC etc.) is required, to be described as 100-240Vac (50/60Hz).

*4: At 100/200V input voltage and maximum output power.

*5: From 85i132Vac or 170i265Vac, constant load.

*6: From No-load to Full-load, constant input voltage. Measured at the sensing point in Remote Sense.

*7: For load voltage change, equal to the unit voltage rating, constant input voltage.

*8: For 6V models the ripple is measured at 2i6V output voltage and full output current. For other models, the ripple is measured at 10i100% output voltage and full output current.

*9: With rated, resistive load.

*10. For 6i300V models: Measured with JEITA RC-9131A (1:1) probe For 600V model: Measured with (10:1) probe.

2.12 SUPPLEMENTAL CHARACTERISTICS

The supplemental characteristics give typical but non-warranted performance characteristics. The supplemental characteristics are useful in assessing applications for the power supply. Sev- eral kinds of supplemental characteristics are listed below.

1.Evaluation Data: Typical performance of the power supply.

2.Reliability Data: Reliability Performance of the power supply.

3.IEC1000 Data: Performance of the power supply under IEC1000 test conditions.

4.EMI Data: Typical EMI (conducted and radiated) performance of the power supply.

The supplemental characteristics data is held in each TDK-Lambda Americas Inc. sales and ser- vice facility. For further details please contact the TDK-Lambda Americas Inc. office nearest you.

11

83-507-5002 Rev. B

Image 19

TDK 750W HALF RACK technical manual Supplemental Characteristics

Contents

Genesystm 750W Half Rack Page Page Genesys Manual Supplement Table of Contents Front and Rear Panel Controls and CONNECTORS………... ……… ……… Isolated Analog Progamming Option ……………………………..…… Warranty Safety Instructions Safety Instructions SICHERHEITS-INSTALLATIONS Anweisungen Anderungen and Bauteileersatz Sicherheits-und WarnsymboleUmweltbedingungen General Description Features and optionsGeneral Information Introduction Parallel operation Multiple output power systemControl via the serial communication port Analog voltage programming and monitoring Accessories Chapter Specifications Front Panel Supplemental Characteristics Genesystm Genh 750W Power Supplies Outline Drawings Initial Inspections InstallationGeneral Preparation for USE Rack Mounting Single unit installation GENH/RM Rack Mounting outline drawings AC Input Power ConnectionLOCATION, Mounting and Cooling AC Source Requirements General TURN-ON Checkout ProcedureAC Input Connector AC Input Cord UVL Check Constant Voltage CheckConstant Current Check OVP Check Connecting the Load AWG Wire termination 6V to 60V Models Noise and Impedance EffectsInductive loads Making the load connections Bus-bars shield mounting 80V to 600V Models 83-507-5002 Rev. B Connecting single loads, remote sensing Connecting single loads, local sensing defaultConnecting multiple loads, radial distribution method Grounding outputs Multiple load connection with distribution terminals Local sensing Sense wiringOutput Terminal Grounding Local and Remote Sensing Remote sensing 10.4 J2 sense connector technical information Front Panel Controls and Indicators Front and Rear Panel Controls and ConnectorsVoltage Auxiliary Function Rear panel connections and controls Number Description Rear Panel Connections and Controls 1 SW1 position function Rear Panel SW1 Setup Switch Resetting the SW1 switch Rear Panel J1 Programming and Monitoring ConnectorMaking J1 connections 83-507-5002 Rev. B Local SignalEnain Ifcom Standard Operation Constant Voltage ModeConstant Current Mode Local Operation Automatic Crossover Setting the OVP levelResetting the OVP circuit Over Voltage Protection OVP Output ON/OFF Control Output SHUT-OFF SO Control VIA Rear Panel J1 ConnectorUnder Voltage Limit UVL Foldback Protection CV/CC Signal ENABLE/DISABLE Control VIA Rear Panel J1 Connector SAFE-START and AUTO-RESTART Modes Psok SignalOver Temperature Protecton OTP Last Setting Memory Series connection for increased output voltage Series Operation Series connection for positive/negative output voltages Series connection for positive and negative output voltage Basic parallel operation Setting up the Master unitSetting up the Slave units Parallel Operation Setting the units as Master or Slave Setting Over Voltage protectionSetting Foldback protection Advanced parallel configuration AST OFF OUT OFF Master and Slave units default operationTo release units from Slave mode Current display accuracy Front Panel Locking DAISY-CHAIN Connection Locked front panel Unlocked front panel LOCAL/REMOTE Analog Indication Remote Analog Programming Remote voltage programming connection Down Remote resistive programming Resisitive Programming of Output Voltage and Current Limit Remote Monitoring of Output Voltage and Current Configuration RS232 & RS485 Remote Control 6 RS232/RS485 port in Local mode Rear Panel RS232/RS485 ConnectorFront panel in Remote mode MD Mode SRQ Retransmission MD Mode DescriptionMD Mode enable Serial communication mode MD Mode SRQ Single power supply Connecting Power Supplies to RS232 or RS485 BUS Communication Interface Protocol Command SET Description Error Messages ID Control Commands Initialization Control CommandsOutput Control Commands OUT? DVC?Filter FILTER? Global Output Commands Enable SRQ retransmission MD Mode Option Required Single Byte CommandsEnable MD Mode MD Mode Option Required Disable SRQ retransmission MD Mode Option Required Print Power On Time Addressed commands with response Read registersRetransmit Last Message Addressed commands without response Acknowledge SRQ Test if MD Mode is InstalledRe-enable SRQ with out reading/clearing the Seve Register 110x Status Control Commands STATUS, Error and SRQ Registers TXD Conditional Registers BIT Service Request Enable and Event Registers Fault Event Register Fault Enable Register Status Event Register Status Enable Register Serial Communication Test SET-UP Power supply set-upCommunication Test PPM/C SpecificationsIsolated Analog Programming Option 1 0-5V/0-10V Option PN IS510 Isolated Programming & Monitoring Connector Setup and Operating Instructions Maintenance OUP Fuse Rating