LOCATION, Mounting and Cooling | TDK 750W HALF RACK specs

3.4.3 GENH/RM Rack Mounting outline drawings:

3.5 LOCATION, MOUNTING AND COOLING

This power supply is fan cooled. The air intake is at the front panel and the exhaust is at the rear panel. Upon installation allow cooling air to each the front panel ventilation inlets. Allow minimum 10cm (4-inch) of unrestricted air space at the front and the rear of the unit.

The power supply should be used in an area that the ambient temperature does not exceed +50°C.

3.6 AC SOURCE REQUIREMENTS

The GenesysTM series can be operated from a nominal 100V to 240V, single phase, 47i63 Hz. The input voltage range and current required for each model is specified in Chapter 2. Ensure that under heavy load, the AC voltage supplied to the power supply does not fall below the speci- fications described in Chapter 2.

3.7 AC INPUT POWER CONNECTION

CAUTION

Connection of this power supply to an AC power source should be made by an electrician or other qualified personnel

WARNING

There is a potential shock hazard if the power supply chassis (with cover in place) is not connected to an electrical safety ground via the safety ground in the AC input connector.

15

83-507-5002 Rev. B

Image 23

TDK 750W HALF RACK technical manual LOCATION, Mounting and Cooling, AC Source Requirements, AC Input Power Connection

Contents

Genesystm 750W Half Rack Page Page Genesys Manual Supplement Table of Contents Front and Rear Panel Controls and CONNECTORS………... ……… ……… Isolated Analog Progamming Option ……………………………..…… Warranty Safety Instructions Safety Instructions SICHERHEITS-INSTALLATIONS Anweisungen Umweltbedingungen Sicherheits-und WarnsymboleAnderungen and Bauteileersatz General Description Features and optionsGeneral Information Introduction Parallel operation Multiple output power systemControl via the serial communication port Analog voltage programming and monitoring Accessories Chapter Specifications Front Panel Supplemental Characteristics Genesystm Genh 750W Power Supplies Outline Drawings Initial Inspections InstallationGeneral Preparation for USE Rack Mounting Single unit installation GENH/RM Rack Mounting outline drawings AC Input Power ConnectionLOCATION, Mounting and Cooling AC Source Requirements General TURN-ON Checkout ProcedureAC Input Connector AC Input Cord UVL Check Constant Voltage CheckConstant Current Check OVP Check Connecting the Load AWG Wire termination 6V to 60V Models Noise and Impedance EffectsInductive loads Making the load connections Bus-bars shield mounting 80V to 600V Models 83-507-5002 Rev. B Connecting multiple loads, radial distribution method Connecting single loads, local sensing defaultConnecting single loads, remote sensing Grounding outputs Multiple load connection with distribution terminals Local sensing Sense wiringOutput Terminal Grounding Local and Remote Sensing Remote sensing 10.4 J2 sense connector technical information Voltage Front and Rear Panel Controls and ConnectorsFront Panel Controls and Indicators Auxiliary Function Rear panel connections and controls Number Description Rear Panel Connections and Controls 1 SW1 position function Rear Panel SW1 Setup Switch Making J1 connections Rear Panel J1 Programming and Monitoring ConnectorResetting the SW1 switch 83-507-5002 Rev. B Local SignalEnain Ifcom Standard Operation Constant Voltage ModeConstant Current Mode Local Operation Automatic Crossover Setting the OVP levelResetting the OVP circuit Over Voltage Protection OVP Output ON/OFF Control Output SHUT-OFF SO Control VIA Rear Panel J1 ConnectorUnder Voltage Limit UVL Foldback Protection CV/CC Signal ENABLE/DISABLE Control VIA Rear Panel J1 Connector SAFE-START and AUTO-RESTART Modes Psok SignalOver Temperature Protecton OTP Last Setting Memory Series connection for increased output voltage Series Operation Series connection for positive/negative output voltages Series connection for positive and negative output voltage Basic parallel operation Setting up the Master unitSetting up the Slave units Parallel Operation Setting the units as Master or Slave Setting Over Voltage protectionSetting Foldback protection Advanced parallel configuration AST OFF OUT OFF Master and Slave units default operationTo release units from Slave mode Current display accuracy Front Panel Locking DAISY-CHAIN Connection Locked front panel Unlocked front panel LOCAL/REMOTE Analog Indication Remote Analog Programming Remote voltage programming connection Down Remote resistive programming Resisitive Programming of Output Voltage and Current Limit Remote Monitoring of Output Voltage and Current Configuration RS232 & RS485 Remote Control Front panel in Remote mode Rear Panel RS232/RS485 Connector6 RS232/RS485 port in Local mode MD Mode SRQ Retransmission MD Mode DescriptionMD Mode enable Serial communication mode MD Mode SRQ Single power supply Connecting Power Supplies to RS232 or RS485 BUS Communication Interface Protocol Command SET Description Error Messages Output Control Commands Initialization Control CommandsID Control Commands OUT? DVC?Filter FILTER? Global Output Commands Enable SRQ retransmission MD Mode Option Required Single Byte CommandsEnable MD Mode MD Mode Option Required Disable SRQ retransmission MD Mode Option Required Retransmit Last Message Addressed commands with response Read registersPrint Power On Time Re-enable SRQ with out reading/clearing the Seve Register Test if MD Mode is InstalledAddressed commands without response Acknowledge SRQ 110x Status Control Commands STATUS, Error and SRQ Registers TXD Conditional Registers BIT Service Request Enable and Event Registers Fault Event Register Fault Enable Register Status Event Register Status Enable Register Communication Test Power supply set-upSerial Communication Test SET-UP PPM/C SpecificationsIsolated Analog Programming Option 1 0-5V/0-10V Option PN IS510 Isolated Programming & Monitoring Connector Setup and Operating Instructions Maintenance OUP Fuse Rating