Setup and Operating Instructions | TDK 750W HALF RACK guide

8.4 SETUP AND OPERATING INSTRUCTIONS

CAUTION

To prevent damage to the unit, do not program the output voltage and current to higher than the power supply rating.

8.4.1Setting up the power supply for 0-5V/0-10V Isolated Programming and Monitoring Perform the following procedure to configure the power supply:

1.Turn the power supply AC power switch to Off.

2.Connect a wire jumper between J1-8 and J1-12 (refer to Table 4-4).

3.Set the Setup switch SW1, positions 1 and 2 to the UP position.

4.Set SW1, position 3 to select the Programming Voltage Range: Down=0-5V, Up=0-10V.

5.Set SW1, position 4 to select the Monitoring Range: Down=0-5V, Up=0-10V.

6.Ensure that SW1, positions 7 and 8 are in the Down position.

7.Connect the programming sources to the mating plug of the Isolated Programming connec- tor. Observe for correct polarity of the voltage source.

NOTE

J1-8 and J1-12 must be shorted together with a wire jumper.

8. Set the programming sources to the desired levels and turn the power supply ON.

8.4.2Setting up the power supply for 4-20mA Isolated Programming and Monitoring Perform the following procedure to configure the power supply:

1.Turn the power supply AC power switch to Off.

2.Connect a wire jumper between J1-8 and J1-12 (refer to Table 4-4).

3.Set the Setup switch SW1, positions 1 and 2 to the Up position.

4.Set SW1, position 3 to the Up position.

5.Set SW1, position 4 to the Up position.

6.Ensure that SW1 positions 1 and 2 to their Up position.

7.Connect the programming source to the mating plug of the Isolated Programming connector. Observe for correct polarity of the voltage source.

NOTE

J1-8 and J1-12 must be shorted together with a wire jumper.

8. Set the programming sources to the desired levels and turn the power supply ON.

NOTE

SW1 position 3 and 4 must be in the Up position for operation with 4-20mA Isolated Programming and Monitoring.

71

83-507-5002 Rev. B

Image 79

TDK 750W HALF RACK technical manual Setup and Operating Instructions

Contents

Genesystm 750W Half Rack Page Page Genesys Manual Supplement Table of Contents Front and Rear Panel Controls and CONNECTORS………... ……… ……… Isolated Analog Progamming Option ……………………………..…… Warranty Safety Instructions Safety Instructions SICHERHEITS-INSTALLATIONS Anweisungen Anderungen and Bauteileersatz Sicherheits-und WarnsymboleUmweltbedingungen General Description Features and optionsGeneral Information Introduction Parallel operation Multiple output power systemControl via the serial communication port Analog voltage programming and monitoring Accessories Chapter Specifications Front Panel Supplemental Characteristics Genesystm Genh 750W Power Supplies Outline Drawings Initial Inspections InstallationGeneral Preparation for USE Rack Mounting Single unit installation GENH/RM Rack Mounting outline drawings AC Input Power ConnectionLOCATION, Mounting and Cooling AC Source Requirements General TURN-ON Checkout ProcedureAC Input Connector AC Input Cord UVL Check Constant Voltage CheckConstant Current Check OVP Check Connecting the Load AWG Wire termination 6V to 60V Models Noise and Impedance EffectsInductive loads Making the load connections Bus-bars shield mounting 80V to 600V Models 83-507-5002 Rev. B Connecting single loads, remote sensing Connecting single loads, local sensing defaultConnecting multiple loads, radial distribution method Grounding outputs Multiple load connection with distribution terminals Local sensing Sense wiringOutput Terminal Grounding Local and Remote Sensing Remote sensing 10.4 J2 sense connector technical information Front Panel Controls and Indicators Front and Rear Panel Controls and ConnectorsVoltage Auxiliary Function Rear panel connections and controls Number Description Rear Panel Connections and Controls 1 SW1 position function Rear Panel SW1 Setup Switch Resetting the SW1 switch Rear Panel J1 Programming and Monitoring ConnectorMaking J1 connections 83-507-5002 Rev. B Local SignalEnain Ifcom Standard Operation Constant Voltage ModeConstant Current Mode Local Operation Automatic Crossover Setting the OVP levelResetting the OVP circuit Over Voltage Protection OVP Output ON/OFF Control Output SHUT-OFF SO Control VIA Rear Panel J1 ConnectorUnder Voltage Limit UVL Foldback Protection CV/CC Signal ENABLE/DISABLE Control VIA Rear Panel J1 Connector SAFE-START and AUTO-RESTART Modes Psok SignalOver Temperature Protecton OTP Last Setting Memory Series connection for increased output voltage Series Operation Series connection for positive/negative output voltages Series connection for positive and negative output voltage Basic parallel operation Setting up the Master unitSetting up the Slave units Parallel Operation Setting the units as Master or Slave Setting Over Voltage protectionSetting Foldback protection Advanced parallel configuration AST OFF OUT OFF Master and Slave units default operationTo release units from Slave mode Current display accuracy Front Panel Locking DAISY-CHAIN Connection Locked front panel Unlocked front panel LOCAL/REMOTE Analog Indication Remote Analog Programming Remote voltage programming connection Down Remote resistive programming Resisitive Programming of Output Voltage and Current Limit Remote Monitoring of Output Voltage and Current Configuration RS232 & RS485 Remote Control 6 RS232/RS485 port in Local mode Rear Panel RS232/RS485 ConnectorFront panel in Remote mode MD Mode SRQ Retransmission MD Mode DescriptionMD Mode enable Serial communication mode MD Mode SRQ Single power supply Connecting Power Supplies to RS232 or RS485 BUS Communication Interface Protocol Command SET Description Error Messages ID Control Commands Initialization Control CommandsOutput Control Commands OUT? DVC?Filter FILTER? Global Output Commands Enable SRQ retransmission MD Mode Option Required Single Byte CommandsEnable MD Mode MD Mode Option Required Disable SRQ retransmission MD Mode Option Required Print Power On Time Addressed commands with response Read registersRetransmit Last Message Addressed commands without response Acknowledge SRQ Test if MD Mode is InstalledRe-enable SRQ with out reading/clearing the Seve Register 110x Status Control Commands STATUS, Error and SRQ Registers TXD Conditional Registers BIT Service Request Enable and Event Registers Fault Event Register Fault Enable Register Status Event Register Status Enable Register Serial Communication Test SET-UP Power supply set-upCommunication Test PPM/C SpecificationsIsolated Analog Programming Option 1 0-5V/0-10V Option PN IS510 Isolated Programming & Monitoring Connector Setup and Operating Instructions Maintenance OUP Fuse Rating