Oup | TDK 750W HALF RACK instruction

SYMPTOM	CHECK	ACTION	REF
Output is present	Is the power supply	Check if the positive or	3.9.6
momentarily but shuts off	configured to Remote	negative load wire is loose.	3.9.8
quickly.The display indicates	sense?
“OUP”.
Output Voltage will not	Is the unit in constant	Check Output Current	5.2.1
adjust. Front panel CC LED	current mode?	setting and load current.	5.2.2
is On.
Output Voltage will not	Check if output voltage is	Set OVP or UVL so they will	5.3
adjust Front panel CV Led is	adjusted above OVP	not limit the output.	5.4
On.	setting or below UVL
	setting.
Output Current will not	Is the unit in constant	Check Output Current and	5.2
adjust. Front panel CV LED	voltage mode?	voltage setting
is on.
Large ripple present in	Is the power supply in	Check load and sense wires	3.9.4
output.	remote sense?	connection for noise and	3.9.8
	Is the voltage drop on the	impedance effects. Minimize
	load wire high?	the drop on the load wires.
No output. Display indicates	Overvoltage Protection	Turn off the AC power	5.3
“OUP”	circuit is tripped.	switch. Check load
		connections. If Analog
		Programming is used, check
		if the OVP is set lower than
		the output.
No output. Front panel	Display indicates “ENA”	Check rear panel J1	5.8
ALARM LED is blinking.		ENABLE connection.
		Setup switch SW1 setting.	4.4
	Display indicates “SO”	Check rear panel J1 Output	5.7
		Shut-Off connection.
	Display indicates “OTP”	Check if air intake or
		exhaust are blocked. Check
		if the unit is installed
		adjacent to heat generating
		equipment.
	Display indicates “Fb”	Check Foldback setting and	5.5
		load current.
Poor Load regulation.	Are sensing wires	Connect the sense wires	3.9.8
Front panel CV LED is on.	connected properly?	according to User’s Manual
		instructions.
The front panel controls are	Is the power supply in	Turn Off the AC power and	7.2.5
non-functional.	Local-Lockout mode?	wait until the display turns
		off. Turn on the AC power
		and press front panel
		REM/LOC button.

73

83-507-5002 Rev. B

Image 81

TDK 750W HALF RACK technical manual Oup

Contents

Genesystm 750W Half Rack Page Page Genesys Manual Supplement Table of Contents Front and Rear Panel Controls and CONNECTORS………... ……… ……… Isolated Analog Progamming Option ……………………………..…… Warranty Safety Instructions Safety Instructions SICHERHEITS-INSTALLATIONS Anweisungen Sicherheits-und Warnsymbole Anderungen and BauteileersatzUmweltbedingungen General Information Features and optionsIntroduction General Description Control via the serial communication port Multiple output power systemAnalog voltage programming and monitoring Parallel operation Accessories Chapter Specifications Front Panel Supplemental Characteristics Genesystm Genh 750W Power Supplies Outline Drawings General InstallationPreparation for USE Initial Inspections Rack Mounting Single unit installation LOCATION, Mounting and Cooling AC Input Power ConnectionAC Source Requirements GENH/RM Rack Mounting outline drawings AC Input Connector TURN-ON Checkout ProcedureAC Input Cord General Constant Current Check Constant Voltage CheckOVP Check UVL Check Connecting the Load AWG Wire termination Inductive loads Noise and Impedance EffectsMaking the load connections 6V to 60V Models Bus-bars shield mounting 80V to 600V Models 83-507-5002 Rev. B Connecting single loads, local sensing default Connecting single loads, remote sensingConnecting multiple loads, radial distribution method Grounding outputs Multiple load connection with distribution terminals Output Terminal Grounding Sense wiringLocal and Remote Sensing Local sensing Remote sensing 10.4 J2 sense connector technical information Front and Rear Panel Controls and Connectors Front Panel Controls and IndicatorsVoltage Auxiliary Function Rear panel connections and controls Number Description Rear Panel Connections and Controls 1 SW1 position function Rear Panel SW1 Setup Switch Rear Panel J1 Programming and Monitoring Connector Resetting the SW1 switchMaking J1 connections 83-507-5002 Rev. B Enain SignalIfcom Local Constant Current Mode Constant Voltage ModeLocal Operation Standard Operation Resetting the OVP circuit Setting the OVP levelOver Voltage Protection OVP Automatic Crossover Under Voltage Limit UVL Output SHUT-OFF SO Control VIA Rear Panel J1 ConnectorFoldback Protection Output ON/OFF Control CV/CC Signal ENABLE/DISABLE Control VIA Rear Panel J1 Connector Over Temperature Protecton OTP Psok SignalLast Setting Memory SAFE-START and AUTO-RESTART Modes Series connection for increased output voltage Series Operation Series connection for positive/negative output voltages Series connection for positive and negative output voltage Setting up the Slave units Setting up the Master unitParallel Operation Basic parallel operation Setting Foldback protection Setting Over Voltage protectionAdvanced parallel configuration Setting the units as Master or Slave To release units from Slave mode Master and Slave units default operationCurrent display accuracy AST OFF OUT OFF Front Panel Locking DAISY-CHAIN Connection Locked front panel Unlocked front panel LOCAL/REMOTE Analog Indication Remote Analog Programming Remote voltage programming connection Down Remote resistive programming Resisitive Programming of Output Voltage and Current Limit Remote Monitoring of Output Voltage and Current Configuration RS232 & RS485 Remote Control Rear Panel RS232/RS485 Connector 6 RS232/RS485 port in Local modeFront panel in Remote mode MD Mode enable Serial communication mode MD Mode DescriptionMD Mode SRQ MD Mode SRQ Retransmission Single power supply Connecting Power Supplies to RS232 or RS485 BUS Communication Interface Protocol Command SET Description Error Messages Initialization Control Commands ID Control CommandsOutput Control Commands Filter DVC?FILTER? OUT? Global Output Commands Enable MD Mode MD Mode Option Required Single Byte CommandsDisable SRQ retransmission MD Mode Option Required Enable SRQ retransmission MD Mode Option Required Addressed commands with response Read registers Print Power On TimeRetransmit Last Message Test if MD Mode is Installed Addressed commands without response Acknowledge SRQRe-enable SRQ with out reading/clearing the Seve Register 110x Status Control Commands STATUS, Error and SRQ Registers TXD Conditional Registers BIT Service Request Enable and Event Registers Fault Event Register Fault Enable Register Status Event Register Status Enable Register Power supply set-up Serial Communication Test SET-UPCommunication Test Isolated Analog Programming Option Specifications1 0-5V/0-10V Option PN IS510 PPM/C Isolated Programming & Monitoring Connector Setup and Operating Instructions Maintenance OUP Fuse Rating