J.Reconnect gray, red, and white leads to the en- gine starter solenoid located on below the exhaust manifold.

K.Reconnect battery ground to the traction clutch side of the cylinder head or the left side of the cylin- der block.

7.Reconnect throttle cable (Fig. 19).

A.Run throttle cable to engine (25).

B.Reinstall clevis pin (29), throttle tab (30), and throttle cable to the engine governor lever. Reinstall and lock cotter pin (31) to the clevis pin.

C.Install throttle cable into the throttle cable clamp (26). Tighten cap screw (43).

8.Reinstall exhaust system (Fig. 19).

A.Position muffler (14) and muffler gasket (45) onto the exhaust manifold. Install capscrews (39) and flat washers (11) to the muffler and exhaust manifold. Tighten cap screws.

B.Reinstall cap screws (36) and washers (13) into the muffler and right rear mount bracket (46).

C.Slide muffler tube through the U±clamp (17). Connect muffler tube to the muffler. Tighten nut (20) and U±clamp.

D.Reinstall muffler clamp (19) to the muffler (14) and muffler tube (15).

9.Reconnect hydraulic hoses from the oil cooler.

A.Unplug hydraulic hose (2) and hydraulic elbow fitting (3). Connect hydraulic supply hose to the hy- draulic elbow fitting. Tighten hose clamp (1) (Fig. 21).

B.Unplug hydraulic return hose (2) and hydraulic fitting (3). Connect hydraulic return hose to the hy- draulic fitting. Tighten hose clamp (1) (Fig. 20).

10.Connect hoses to the engine (Fig. 19).

A.Connect fuel hose (return) to the injector nozzle piping and tighten hose clamp.

B.Unplug fuel hose (44). Connect fuel hose to the lift pump and tighten hose clamp (38).

C.Connect upper radiator hose (18) and lower ra- diator hose (24) to the engine. Tighten hose clamps (23).

D.Connect air filter hose to the engine (25).

11.Open fuel shut±off valves under the fuel tank and on the fuel filter.

12.Fill hydraulic reservoir with hydraulic fluid as de- scribed in the General Information section of Chapter 4

± Hydraulic System. Check reservoir for leaks.

13.Add antifreeze to radiator as described in Checking the Cooling System.

14.Slide the left foot rest (5) (Fig. 17) onto the adjusting rod (2) (Fig. 18). Reinstall cap screws (3) and flange nut

(4) securing the left footrest (5) to the frame. Tighten cap screws (Fig. 17).

15.Connect adjusting rod to brake arm (3) Install and lock cotter pin (1) to the adjusting rod (2) (Fig. 18).

16.Reinstall fender bracket (2) and left fender (1) to the radiator side of the frame (Fig. 17).

A.Secure both cap screws (3) and left fender bracket (2) to the frame.

B.Reinstall remaining cap screws (3) and flange nuts (4) securing the fender to the fender bracket and frame.

C.Secure cap screw (3) and flange nut (4) to the left foot rest (5) and the left fender (1).

17.Replace traction pump drive belt as described in Traction (Electric) Clutch of the Service and Repairs section of Chapter 5 ± Electrical System.

18.Adjust traction pump drive belt as described in the Adjustment section of Chapter 4 ± Hydraulic system.

19.Connect negative (±) and then positive (+) battery cables at the battery.

20.Adjust hand brake as described in the Adjustment section of Chapter 6 ± Wheels and Brakes.

21.Adjust throttle linkage as described in the Adjust- ment section of this chapter.

22.Bleed fuel system. See Bleeding the Fuel System.

23.Check oil level as described in Changing the Engine OIl and Filter.

24.Replace access covers to the engine.

A.Reinstall left rear panel (radiator side) which supports the instrument panel.

B.Reinstall right side panel which accesses the traction pump drive belt.

C.Reinstall hood to the machine and close.

Engine

Reelmaster 2300±D/2600±D

Page 3 ± 19

Engine

Page 37
Image 37
Toro 2600D, 2300-D service manual Engine

2600D, 2300-D specifications

The Toro 2300-D and 2600-D are industry-leading reel mowers specifically designed for the professional turf care market. Known for their durability, efficiency, and advanced technology, these models provide exceptional cutting performance for golf courses, sports fields, and other high-quality turf applications.

One of the standout features of the Toro 2300-D and 2600-D is their powerful engines. Powered by efficient diesel engines, these mowers deliver robust performance while being fuel-efficient. This capability ensures extended operation periods, allowing grounds crews to maintain pristine conditions across large areas without frequent refuelling stops.

Both models are equipped with Toro’s exclusive DPA (Dual Precision Adjust) cutting system, providing precise cutting heights for optimal turf health. This system allows for adjustments from 1/8 inch to 1 inch, enabling operators to achieve the correct level for various grass types and turf conditions. This level of precision ensures a clean cut and promotes the overall health of the grass.

Another notable characteristic is the ergonomic design, which includes a comfortable operator station to reduce fatigue during extended use. The controls are intuitively located, enabling easy access and operation, and the mower's compact design allows for nimble maneuverability around obstacles, ensuring that every inch of turf can be accurately maintained.

In terms of technology, the Toro 2300-D and 2600-D feature advanced traction control systems that provide excellent grip and stability on slopes and uneven terrain. The lightweight alloy construction of the frame contributes to this stability, giving operators confidence whether they are working on flat surfaces or more challenging landscapes.

Furthermore, these mowers are designed with sustainability in mind. The diesel engines not only offer efficiency but also are compliant with strict emissions standards, making them an environmentally responsible choice for turf maintenance.

The Toro 2300-D and 2600-D also feature a robust maintenance management system that alerts operators of necessary maintenance tasks, promoting longer lifespans for components and enhancing overall performance.

In summary, the Toro 2300-D and 2600-D deliver cutting-edge technologies and features, including powerful engines, versatile cutting systems, ergonomic design, advanced traction control, and sustainability focus. These models represent the pinnacle of reel mower engineering, making them ideal choices for professionals dedicated to maintaining the finest playing surfaces.