APPENDIX 2 MESSAGES AND LEDS

EO1-33032

APPENDIX 2 MESSAGES AND LEDS

APPENDIX 2 MESSAGES AND LEDS

Appendix 2 describes the LCD messages displayed on the operation panel.

Symbols in the message

1:Å: The LED is illuminated. ~: The LED is flashing. z: The LED is unlit.

2:****: the remaining number of labels to be printed. Up to 9999 (pieces)

3:%%%%%%%: ATA Card’s remaining memory 0 to 9999999 (in K bytes)

4:###: Flash memory card remaining memory for PC save area: 0 to 895 (in K bytes)

5:&&&&: Remaining flash memory capacity for storing writable characters 0 to 3147 (in K bytes)

 

 

 

 

 

LED Indication

 

Restoration

Acceptance of

No.

LCD Message

 

 

 

Printer Status

by RESTART

Status Request

 

 

 

POWER

ONLINE

ERROR

key Yes/No

Reset Command

 

 

 

 

 

 

 

 

 

 

 

 

 

Yes/No

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Å

 

In online mode

-----

Yes

1

21/,1(

 

 

 

~

 

In online mode (The printer is receiving

-----

Yes

 

 

 

 

 

 

 

 

a communication)

 

 

2

+($'23(1

 

 

 

 

The print head block is opened in online

-----

Yes

 

 

 

 

mode.

 

 

3

3$86(

 

￿￿￿￿

 

 

z

The printer is paused.

Yes

Yes

 

 

 

 

 

 

 

 

A parity, overrun, or framing error has

Yes

Yes

4

&2006(5525

 

 

 

 

occurred during communication through

 

 

 

 

 

 

 

 

 

 

the RS-232C port.

 

 

5

3$3(5-$0

 

 

 

 

The media has jammed during feed.

Yes

Yes

6

123$3(5

 

 

 

 

 

The media has run out, or the media is

Yes

Yes

 

 

 

 

 

not loaded correctly.

 

 

 

 

 

 

 

 

 

 

The ribbon has run out, or has snapped.

Yes

Yes

7

5,%%21

 

5525

 

 

 

A problem has occurred with the sensor

 

 

 

 

 

 

 

 

 

 

that determines the torque for the ribbon

 

 

 

 

 

 

 

 

 

 

motor.

 

 

8

+($'23(1

 

 

 

 

Feeding or printing was attempted with

Yes

Yes

 

 

 

 

 

 

 

 

the print head block open.

 

 

9

&29(5

 

 

 

 

 

 

Feeding or printing was attempted with

Yes

Yes

 

 

 

 

 

 

the top cover open.

 

 

 

 

 

 

 

 

 

 

 

 

10

,1&+23(1

 

 

 

 

Feeding or printing was attempted with

Yes

Yes

￿

 

 

 

the pinch roller raised.

 

 

11

3((/23(1

￿

 

 

 

Feeding or printing was attempted with

Yes

Yes

 

 

 

 

 

 

 

 

the strip pinch roller unit open.

 

 

12

*8,'(

 

1

￿￿￿

 

 

 

Feeding or printing was attempted with

Yes

Yes

 

 

 

 

the media guide plate removed.

 

 

13

(;&(66+$'7(03

 

z

Å

The print head has overheated.

No

Yes

 

 

￿

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

In writable character or PC command

-----

Yes

14

6RU$9,1*￿￿￿￿￿￿(55￿

 

Å

z

save mode

 

 

 

 

 

 

 

 

 

 

 

 

 

15

/$6+:5,7(

 

 

 

 

An error has occurred while formatting

No

Yes

 

 

 

 

the flash memory or ATA card.

 

 

 

 

 

 

 

 

 

 

An erase error has occurred in

No

Yes

16

250$7(5525

 

 

 

formatting the flash memory or ATA

 

 

 

 

 

 

 

 

 

 

card.

 

 

17

)/6+&')8//

 

 

 

Data cannot be stored because the flash

No

Yes

 

 

 

 

 

 

 

 

memory or ATA card is full.

 

 

18

+($'(5525

 

 

 

 

There is a problem with the print head.

Yes

Yes

19

messageDisplay of(SeeerrorNotes.)

Å

z

Å

theThedisplayeddata analyzercommand.has found an error in

Yes

Yes

A2- 1

Page 48
Image 48
Toshiba R-TH10, B-492L owner manual Appendix 2 Messages and Leds, Symbols in the message