Appendix 4 System Mode, A4.1 Operation Panel | Toshiba B-492L

APPENDIX 4 SYSTEM MODE

EO1-33032

A4.1 Operation Panel

APPENDIX 4 SYSTEM MODE

IMPORTANT!

If System Mode is needed for any other purposes, please contact a TOSHIBA TEC authorized service representative before performing any operation in System Mode.

A4.1 Operation Panel

Appendix 4 describes usage of the keys on the Operation Panel in System Mode.

For end users, System Mode should be used for the following five purposes:

∙To reset the printer. (Reset mode)

∙To check and print the system status, the Maintenance Counter, and to check the Print Head Elements.

∙To make fine adjustment to the media handling.

∙To perform a test print for checking print quality.

∙To print the raw data being received by the printer (Dump mode).

The figure below shows the Operation Panel and key functions.

LCD Message Display

	POWER LED
	(Green)	POWER	ON LINE	ERROR
	[RESTART] key

	[FEED] key	FEED	RESTART	PAUSE

ERROR LED (Red)

ON LINE LED (Green)

[PAUSE] key

NOTE:

Use the [RESTART] key to resume printing after a pause condition, or after clearing an error.

The LCD Message Display shows messages to indicate the printer’s current status. Up to 16 characters can be displayed on this line.

There are three LEDs on the Operation Panel.

LED	Illuminates when…
POWER	The printer is turned on.
ON LINE	The printer is ready to print.
ERROR	Any error occurs on the printer.

In System Mode, the [FEED], [RESTART] and [PAUSE] keys function as described below.

	FEED	Used to navigate the parameter mode or to fine adjust
	FEED	the parameters in the negative direction (- Down).
		the parameters in the negative direction (- Down).
		Used to release the printer from Pause condition, to
		navigate the parameter mode, or to fine adjust the
	RESTART	parameters in the positive direction (+ Up).
	RESTART	By pressing and holding the [RESTART] key in Pause
		By pressing and holding the [RESTART] key in Pause
		condition for more than 3 sec., the printer enters the
		system mode.
		Used to stop printing operation temporarily, to select
		the parameter mode, or used as an enter key.
	PAUSE	By pressing and holding the [PAUSE] key in Pause
		condition for more than 3 sec., the printer enters the
		threshold setting mode.

A4- 1

Image 51

Toshiba B-492L, R-TH10 owner manual Appendix 4 System Mode, A4.1 Operation Panel

Contents

492L/R-TH10 Series For QQ For QP CE Compliance for EU only Wkhsoxj Request Regarding Maintenance Precautions Table of Contents Appendix 2 Messages and LED Unpacking Introduction FeaturesAccessories Product Overview Dimensions Appearance of the PrinterType Type Side View Front View Interior Operation PanelType Appearance of the Power Supply Unit Precautions Printer Setup Procedure before Operation Connecting the Cables to Your Printer Connecting the Power Cord Turning the Printer Turning on the PrinterTurning OFF the Printer Loading the Media Causing injury Paper Holder Media Guide Setting the black mark sensor position Setting the feed gap sensor position Strip mode Batch mode Loading the Media Loading the Ribbon Pcmcia Cards Inserting the Optional Pcmcia Cards Test Print Operation Panel On Line Mode To be printed Operation Maintenance CleaningPrint Head/Platen Media Guide Plate/ Pinch Roller/Sensors Pinch Roller Feed Roller Paper Guide B Locking Screw Covers and Panels Paper Holder Care/Handling of the Media and Ribbon Restart key TroubleshootingError Messages Error Messages Problems/Causes Solutions Possible Problems Error Messages Problems/Cause SolutionsPossible Problems Causes Solutions Removing Jammed Media Threshold Setting Threshold Setting Printer Operation Overview Installing the Printer Drivers Interface Driver InstallationSystem Requirements System Change to the Software License Agreement screen Cont Driver Installation Driver files copy will start Uninstalling the TEC B-492 Printer Driver Uninstalling the TEC B-492 Printer Driver Appendix 1 Specifications A1.1 PrinterModel 492L/R-TH10-QQ 492L/R-TH10-QP Option Name Type Description Source A1.2 OptionsA1.3 Media A1.3.1 Media Type A1.3.2 Detection Area of the Transmissive Sensor A1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective Sensor A1.4 Ribbon Appendix 2 Messages and Leds Symbols in the message 53&$ „Interface Cables Appendix 3 Interface A4.1 Operation Panel Appendix 4 System Mode 2PARAMETER SET 5SENSOR ADJ RAM Clear 7IP Address A4.2 Overview A4.4 Self-Diagnostic Test A4.3 Reset Mode Ribbon type selection A4.4 Self-DiagnosticMaintenance counter/parameter settings print out Test Print head element check 2PAUSE63 Feed key 567 Cont Fine AdjustmentStrip Position Fine Adjustment A4.5 Printer Parameter $&.$-PP Back Feed Length Fine Adjustment Feed $-867PP A4.5 Printer Parameter X Axis Fine Adjustment Cont Print Thermal Transfer PrintThermal Direct Print 1Rewind$-!Motor 5%1Feed$-Motor% Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor Black Mark Sensor Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor Selection Print Condition SettingA4.6 Test Print Test Print menu contains the following Specifying the Print Condition for the Test Print Issue Count Setting Print Speed Setting Sensor Type SelectionRibbon Type Selection Label Length Setting Issue Mode Selection Slant Line 3 dots Test Print Pattern SelectionPause key Slant Line 1 dot Barcode Non-PrintingFactory Test Auto Print $87235,17 755/$1 A4.7 Dump Mode A4.8 Additional Information A4.8.1 Self-Diagnostic Test Result Sample and Descriptions Sdram 8MB EXP.I/O Print Head Resistance Rank Table Total Feed ∙ Descriptions of the Maintenance Counter XON+READY Auto Busy A4.8.3 Magnified Views of Slant Line Pattern Appendix 5 Print Samples UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits CODE39 Full Ascii KIX Code MaxiCode UPC-A+2 digits UPC-A+5 digits Glossaries Pre-printed label Index Index