Appendix 3 Interface, „Interface Cables | Toshiba R-TH10, B-492L

APPENDIX 3 INTERFACE

EO1-33032

APPENDIX 3 INTERFACE

APPENDIX 3 INTERFACE

„Interface Cables

To prevent radiation and reception of electrical noise, the interface cables must meet the following requirements:

∙Fully shielded and fitted with metal or metallized connector housings.

∙Keep as short as possible.

∙Should not be bundled tightly with power cords.

∙Should not be tied to power line conduits.

„RS-232C Cable description

The serial data cable used to connect the printer to a host computer should be one of the following two types:

DB-9S											DB-9P
Connector to PC											Connector to Printer
Pin No.	Signal										Pin No.		Signal
1	N.C.									1			N.C.
2	RXD									2			TXD
2	RXD									2			TXD
3	TXD									3			RXD
3	TXD									3			RXD
4	DTR									4			DSR
4	DTR									4			DSR
5	GND									5			SG
5	GND									5			SG
6	DSR									6			DTR
6	DSR									6			DTR
7	RTS									7			CTS
7	RTS									7			CTS
8	CTS									8			RTS
8	CTS									8			RTS
9	N.C.									9			N.C.
Housing	Shield										Housing		Shield
Housing	Shield										Housing		Shield
DB-25S											DB-9P
Connector to PC											Connector to Printer
Pin No.	Signal										Pin No.		Signal
1	Shield										1		N.C.
1	Shield										1		N.C.
2	TXD										2		TXD
3	RXD										3		RXD
4	RTS										4		DSR
5	CTS										5		SG
6	DSR										6		DTR
6	DSR										6		DTR
7	GND										7		CTS
20	DTR										8		RTS
20	DTR										8		RTS
											9		N.C.

NOTE:

Use an RS-232C cable with inch type securing screws on the connector.

A3-1

Image 50

Toshiba R-TH10, B-492L owner manual Appendix 3 Interface, „Interface Cables

Contents

492L/R-TH10 Series For QP CE Compliance for EU only For QQ Wkhsoxj Precautions Request Regarding Maintenance Table of Contents Appendix 2 Messages and LED Product Overview Introduction FeaturesAccessories Unpacking Type DimensionsAppearance of the Printer Front View Type Side View Type InteriorOperation Panel Appearance of the Power Supply Unit Printer Setup Precautions Procedure before Operation Connecting the Cables to Your Printer Connecting the Power Cord Turning OFF the Printer Turning the PrinterTurning on the Printer Causing injury Loading the Media Paper Holder Media Guide Setting the feed gap sensor position Setting the black mark sensor position Batch mode Strip mode Loading the Media Loading the Ribbon Pcmcia Cards Test Print Inserting the Optional Pcmcia Cards On Line Mode Operation Panel Operation To be printed Print Head/Platen MaintenanceCleaning Media Guide Plate/ Pinch Roller/Sensors Pinch Roller Feed Roller Paper Guide B Locking Screw Paper Holder Covers and Panels Care/Handling of the Media and Ribbon Error Messages Problems/Causes Solutions TroubleshootingError Messages Restart key Possible Problems Causes Solutions Possible ProblemsError Messages Problems/Cause Solutions Threshold Setting Removing Jammed Media Threshold Setting Overview Installing the Printer Drivers Printer Operation System Driver InstallationSystem Requirements Interface Cont Change to the Software License Agreement screen Driver Installation Driver files copy will start Uninstalling the TEC B-492 Printer Driver Uninstalling the TEC B-492 Printer Driver Model 492L/R-TH10-QQ 492L/R-TH10-QP Appendix 1 SpecificationsA1.1 Printer A1.3.1 Media Type A1.2 OptionsA1.3 Media Option Name Type Description Source A1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print Area A1.4 Ribbon Symbols in the message Appendix 2 Messages and Leds 53&$ Appendix 3 Interface „Interface Cables Appendix 4 System Mode A4.1 Operation Panel A4.2 Overview 2PARAMETER SET 5SENSOR ADJ RAM Clear 7IP Address A4.3 Reset Mode A4.4 Self-Diagnostic Test Test A4.4 Self-DiagnosticMaintenance counter/parameter settings print out Ribbon type selection Print head element check 2PAUSE63 567 Feed key A4.5 Printer Parameter Fine AdjustmentStrip Position Fine Adjustment Cont Back Feed Length Fine Adjustment $&.$-PP A4.5 Printer Parameter X Axis Fine Adjustment Cont Feed $-867PP Thermal Direct Print PrintThermal Transfer Print Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor 1Rewind$-!Motor 5%1Feed$-Motor% Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor Black Mark Sensor Test Print menu contains the following Print Condition SettingA4.6 Test Print Selection Issue Count Setting Specifying the Print Condition for the Test Print Ribbon Type Selection Print Speed SettingSensor Type Selection Issue Mode Selection Label Length Setting Slant Line 1 dot Test Print Pattern SelectionPause key Slant Line 3 dots Factory Test BarcodeNon-Printing A4.7 Dump Mode Auto Print $87235,17 755/$1 A4.8.1 Self-Diagnostic Test Result Sample and Descriptions A4.8 Additional Information Sdram 8MB Print Head Resistance Rank Table EXP.I/O Total Feed ∙ Descriptions of the Maintenance Counter XON+READY Auto A4.8.3 Magnified Views of Slant Line Pattern Busy Appendix 5 Print Samples CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits UPC-A+2 digits UPC-A+5 digits KIX Code MaxiCode Glossaries Pre-printed label Index Index