2PAUSE63 | Toshiba R-TH10, B-492L instruction

EO1-33032 A4.5 Printer Parameter Fine Adjustment

APPENDIX 4 SYSTEM MODE

	A4.5 Printer Parameter	The Printer Parameter Fine Adjustment menu contains the following.
	Fine Adjustment	!$'-8676(7
	Outline of Printer Parameter
	Fine Adjustment	)(('[PAUSE]$'-PP
	In the Printer Parameter Fine
	Adjustment mode, Fine				Feed Length Fine Adjustment
	adjustments can be made for each				Feed Length Fine Adjustment
	adjustments can be made for each	',6$[PAUSE]'-PP
	parameter, like Print tone, Print	;%$$&'.-867$'-PPPP
	start position, Threshold, etc.				Strip Position Fine Adjustment
	which can also be set by PC				Strip Position Fine Adjustment
	which can also be set by PC	721($'-7!			(Thermal Transfer)
		721($'-7!			(Thermal Transfer)
	commands. This is useful when		[PAUSE]
	commands. This is useful when
	using several types of media in				Back Feed Length Fine Adjustment
	rotation or when the print start				Back Feed Length Fine Adjustment
	rotation or when the print start	721($'-'!			(Direct Thermal)
		721($'-'!			(Direct Thermal)
	position or strip position requires		[PAUSE]
	some fine adjustment.				X Axis Fine Adjustment
					X Axis Fine Adjustment
			[PAUSE]
					Print Tone Fine Adjustment
			[PAUSE]
					Print Tone Fine Adjustment
			[PAUSE]
		5%1	$'-):!		Ribbon Motor Drive Voltage Fine
		5%1	$'-):!		Adjustment (Rewind Motor)
			[PAUSE]
		5%1	$'-%.!		Ribbon Motor Drive Voltage Fine
		5%1	$'-%.!		Adjustment (Feed Motor)
		7+5(6+2/[PAUSE]'5!9			Threshold Fine Adjustment (Black
		7+5(6+2/[PAUSE]'7!9			Mark Sensor)
		7+5(6+2/[PAUSE]'7!9			Threshold Fine Adjustment (Feed
		3(/2))[PAUSE]63(('			Gap Sensor)
		3(/2))[PAUSE]63(('			Strip Motor Driving Speed Fine
			[PAUSE]		Adjustment
			[PAUSE]

A4- 6

Image 56

Toshiba R-TH10, B-492L owner manual 2PAUSE63

Contents

492L/R-TH10 Series For QP CE Compliance for EU only For QQ Wkhsoxj Precautions Request Regarding Maintenance Table of Contents Appendix 2 Messages and LED Introduction Features AccessoriesProduct Overview Unpacking Type DimensionsAppearance of the Printer Front View Type Side View Type InteriorOperation Panel Appearance of the Power Supply Unit Printer Setup Precautions Procedure before Operation Connecting the Cables to Your Printer Connecting the Power Cord Turning OFF the Printer Turning the PrinterTurning on the Printer Causing injury Loading the Media Paper Holder Media Guide Setting the feed gap sensor position Setting the black mark sensor position Batch mode Strip mode Loading the Media Loading the Ribbon Pcmcia Cards Test Print Inserting the Optional Pcmcia Cards On Line Mode Operation Panel Operation To be printed Print Head/Platen MaintenanceCleaning Media Guide Plate/ Pinch Roller/Sensors Pinch Roller Feed Roller Paper Guide B Locking Screw Paper Holder Covers and Panels Care/Handling of the Media and Ribbon Troubleshooting Error MessagesError Messages Problems/Causes Solutions Restart key Possible Problems Causes Solutions Possible ProblemsError Messages Problems/Cause Solutions Threshold Setting Removing Jammed Media Threshold Setting Overview Installing the Printer Drivers Printer Operation Driver Installation System RequirementsSystem Interface Cont Change to the Software License Agreement screen Driver Installation Driver files copy will start Uninstalling the TEC B-492 Printer Driver Uninstalling the TEC B-492 Printer Driver Model 492L/R-TH10-QQ 492L/R-TH10-QP Appendix 1 SpecificationsA1.1 Printer A1.2 Options A1.3 MediaA1.3.1 Media Type Option Name Type Description Source A1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print Area A1.4 Ribbon Symbols in the message Appendix 2 Messages and Leds 53&$ Appendix 3 Interface „Interface Cables Appendix 4 System Mode A4.1 Operation Panel A4.2 Overview 2PARAMETER SET 5SENSOR ADJ RAM Clear 7IP Address A4.3 Reset Mode A4.4 Self-Diagnostic Test A4.4 Self-Diagnostic Maintenance counter/parameter settings print outTest Ribbon type selection Print head element check 2PAUSE63 567 Feed key Fine Adjustment Strip Position Fine AdjustmentA4.5 Printer Parameter Cont Back Feed Length Fine Adjustment $&.$-PP A4.5 Printer Parameter X Axis Fine Adjustment Cont Feed $-867PP Thermal Direct Print PrintThermal Transfer Print Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor 1Rewind$-!Motor 5%1Feed$-Motor% Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor Black Mark Sensor Print Condition Setting A4.6 Test PrintTest Print menu contains the following Selection Issue Count Setting Specifying the Print Condition for the Test Print Ribbon Type Selection Print Speed SettingSensor Type Selection Issue Mode Selection Label Length Setting Test Print Pattern Selection Pause keySlant Line 1 dot Slant Line 3 dots Factory Test BarcodeNon-Printing A4.7 Dump Mode Auto Print $87235,17 755/$1 A4.8.1 Self-Diagnostic Test Result Sample and Descriptions A4.8 Additional Information Sdram 8MB Print Head Resistance Rank Table EXP.I/O Total Feed ∙ Descriptions of the Maintenance Counter XON+READY Auto A4.8.3 Magnified Views of Slant Line Pattern Busy Appendix 5 Print Samples CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits UPC-A+2 digits UPC-A+5 digits KIX Code MaxiCode Glossaries Pre-printed label Index Index