A4.2 Overview | Toshiba R-TH10, B-492L specification

This will Reset the printer.

This leads to the Self-Diagnostic Test menu.

This leads to the Parameter Setting menu.

This leads to the Printer Parameter Fine Adjustment menu.

This leads to the Test Print menu.

This leads to the Sensor Adjustment menu.

This leads to the RAM Clear menu.

This leads to the IP Address Setting menu.

This leads to the DUMP mode menu.

APPENDIX 4 SYSTEM MODE

EO1-33032

A4.2 Overview

A4.2 Overview

IMPORTANT!

The following menus are for Service Personnel only:

<2>PARAMETER SET <5>SENSOR ADJ. <6>RAM CLEAR <7>IP ADDRESS

Please do not change the settings for these items, as doing so may cause the printer to malfunction.

If you should accidentally enter these System Modes, to exit just turn the power off. If you should change any of the settings by accident and the printer malfunctions, please contact your nearest TOSHIBA TEC service representative.

NOTE:

1.To navigate the System Mode menus the [RESTART] and [FEED] key can be used.

2.Pressing the [PAUSE] key will enter the sub menus of each System Mode menu.

Flowcharts of each sub menu are provided on the following pages.

The System Mode consists of nine main menu items: Reset, Self- Diagnostic Test, Parameter Setting, Printer Parameter Fine Adjustment, Test Print, Sensor Adjustment, RAM Clear, IP Address Setting, and Dump mode.

the display!5(6(7!.',$*[RESTART]9[[

Press the [PAUSE] key so that the printer enters the Pause condition. Then, press and hold the [RESTART] key until “<0>RESET” appears on

[FEED]!3$5$0(7(5[RESTART]6(7

[FEED]

[RESTART]

[FEED]!7(67!$'-8673[RESTART]5,176(7 !6(1625$'-

[FEED] [RESTART]

[FEED]!5$0&/([RESTART]$5

[FEED]!!'803,3$''5(6602'([RESTART]

[FEED] [RESTART]

[FEED] [RESTART]

[FEED]

A4- 2

Image 52

Toshiba R-TH10, B-492L owner manual A4.2 Overview, 2PARAMETER SET 5SENSOR ADJ RAM Clear 7IP Address

Contents

492L/R-TH10 Series For QP CE Compliance for EU only For QQ Wkhsoxj Precautions Request Regarding Maintenance Table of Contents Appendix 2 Messages and LED Introduction Features AccessoriesProduct Overview Unpacking Appearance of the Printer DimensionsType Front View Type Side View Operation Panel InteriorType Appearance of the Power Supply Unit Printer Setup Precautions Procedure before Operation Connecting the Cables to Your Printer Connecting the Power Cord Turning on the Printer Turning the PrinterTurning OFF the Printer Causing injury Loading the Media Paper Holder Media Guide Setting the feed gap sensor position Setting the black mark sensor position Batch mode Strip mode Loading the Media Loading the Ribbon Pcmcia Cards Test Print Inserting the Optional Pcmcia Cards On Line Mode Operation Panel Operation To be printed Cleaning MaintenancePrint Head/Platen Media Guide Plate/ Pinch Roller/Sensors Pinch Roller Feed Roller Paper Guide B Locking Screw Paper Holder Covers and Panels Care/Handling of the Media and Ribbon Troubleshooting Error MessagesError Messages Problems/Causes Solutions Restart key Error Messages Problems/Cause Solutions Possible ProblemsPossible Problems Causes Solutions Threshold Setting Removing Jammed Media Threshold Setting Overview Installing the Printer Drivers Printer Operation Driver Installation System RequirementsSystem Interface Cont Change to the Software License Agreement screen Driver Installation Driver files copy will start Uninstalling the TEC B-492 Printer Driver Uninstalling the TEC B-492 Printer Driver A1.1 Printer Appendix 1 SpecificationsModel 492L/R-TH10-QQ 492L/R-TH10-QP A1.2 Options A1.3 MediaA1.3.1 Media Type Option Name Type Description Source A1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print Area A1.4 Ribbon Symbols in the message Appendix 2 Messages and Leds 53&$ Appendix 3 Interface „Interface Cables Appendix 4 System Mode A4.1 Operation Panel A4.2 Overview 2PARAMETER SET 5SENSOR ADJ RAM Clear 7IP Address A4.3 Reset Mode A4.4 Self-Diagnostic Test A4.4 Self-Diagnostic Maintenance counter/parameter settings print outTest Ribbon type selection Print head element check 2PAUSE63 567 Feed key Fine Adjustment Strip Position Fine AdjustmentA4.5 Printer Parameter Cont Back Feed Length Fine Adjustment $&.$-PP A4.5 Printer Parameter X Axis Fine Adjustment Cont Feed $-867PP Thermal Transfer Print PrintThermal Direct Print Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor 1Rewind$-!Motor 5%1Feed$-Motor% Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor Black Mark Sensor Print Condition Setting A4.6 Test PrintTest Print menu contains the following Selection Issue Count Setting Specifying the Print Condition for the Test Print Sensor Type Selection Print Speed SettingRibbon Type Selection Issue Mode Selection Label Length Setting Test Print Pattern Selection Pause keySlant Line 1 dot Slant Line 3 dots Non-Printing BarcodeFactory Test A4.7 Dump Mode Auto Print $87235,17 755/$1 A4.8.1 Self-Diagnostic Test Result Sample and Descriptions A4.8 Additional Information Sdram 8MB Print Head Resistance Rank Table EXP.I/O Total Feed ∙ Descriptions of the Maintenance Counter XON+READY Auto A4.8.3 Magnified Views of Slant Line Pattern Busy Appendix 5 Print Samples CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits UPC-A+2 digits UPC-A+5 digits KIX Code MaxiCode Glossaries Pre-printed label Index Index