A4.8 Additional Information | Toshiba B-492L, R-TH10 instruction

APPENDIX 4 SYSTEM MODE

EO1-33032

A4.8 Additional Information

A4.8 Additional Information

A4.8.1 Self-Diagnostic Test Result Sample and Descriptions

∙Print Sample

(1)	PROGRAM	B-492	20SEP2001
		V1.0A	FMRM0067001: 1A00
(2)	BOOT	B-492	01SEP2001
		V1.0	FMRM0066901:8500
(3)	FONT	5600
(4)	EEPROM	OK
(5)	SDRAM	8MB
(6)	CARD	SLOT1	ATA
		SLOT2	LAN
(7)	SENSOR	[H]20°C [A]22°C [S]25°C
		[R]4.2V [T]2.5V
		[RANK]7
(8)	DIP SW	1: ON	2: OFF 3: OFF
(9)	EXP.I/O	NG
(10)	KEY BRD	NG

NOTES:

1.Print conditions:

Preset count: 1, Print speed: 5”/sec., Sensor: No sensor, Printing method: Thermal transfer,

Supply length: 59 mm, Issue mode: Batch printing

2.Software version No., Part No. of ROM and checksum will vary with the software version of PROGRAM ROM.

3.The last two digits of the checksum are usually “00”.

4.The symbol”°” of ‘°C” may not be printed depending on the type of character code selected.

∙Descriptions

(1)Program ROM Check (Model Name, Date, Version, Part number, Checksum)

PROGRAM B-492

20SEP2001

Program area

V1.0

A

FMRM0067001:

1A00

Checksum

Model name

Part No. of ROM or software

Software version No.

Revision No.: Space or A to Z

(2) Boot Check (Model Name, Date, Version, Part Number, Checksum)

BOOT B-492

01SEP2001

Boot area

V1.0

A

FMRM0066901:

8500

Checksum of Boot area

Model name

Part No. of ROM or software

Software version No.

Revision No.: Space or A to Z

A4-21

Image 71

Toshiba B-492L, R-TH10 owner manual A4.8 Additional Information, A4.8.1 Self-Diagnostic Test Result Sample and Descriptions

Contents

492L/R-TH10 Series For QQ For QP CE Compliance for EU only Wkhsoxj Request Regarding Maintenance Precautions Table of Contents Appendix 2 Messages and LED Unpacking Introduction FeaturesAccessories Product Overview Type DimensionsAppearance of the Printer Type Side View Front View Type InteriorOperation Panel Appearance of the Power Supply Unit Precautions Printer Setup Procedure before Operation Connecting the Cables to Your Printer Connecting the Power Cord Turning OFF the Printer Turning the PrinterTurning on the Printer Loading the Media Causing injury Paper Holder Media Guide Setting the black mark sensor position Setting the feed gap sensor position Strip mode Batch mode Loading the Media Loading the Ribbon Pcmcia Cards Inserting the Optional Pcmcia Cards Test Print Operation Panel On Line Mode To be printed Operation Print Head/Platen MaintenanceCleaning Media Guide Plate/ Pinch Roller/Sensors Pinch Roller Feed Roller Paper Guide B Locking Screw Covers and Panels Paper Holder Care/Handling of the Media and Ribbon Restart key TroubleshootingError Messages Error Messages Problems/Causes Solutions Possible Problems Causes Solutions Possible ProblemsError Messages Problems/Cause Solutions Removing Jammed Media Threshold Setting Threshold Setting Printer Operation Overview Installing the Printer Drivers Interface Driver InstallationSystem Requirements System Change to the Software License Agreement screen Cont Driver Installation Driver files copy will start Uninstalling the TEC B-492 Printer Driver Uninstalling the TEC B-492 Printer Driver Model 492L/R-TH10-QQ 492L/R-TH10-QP Appendix 1 SpecificationsA1.1 Printer Option Name Type Description Source A1.2 OptionsA1.3 Media A1.3.1 Media Type A1.3.2 Detection Area of the Transmissive Sensor A1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective Sensor A1.4 Ribbon Appendix 2 Messages and Leds Symbols in the message 53&$ „Interface Cables Appendix 3 Interface A4.1 Operation Panel Appendix 4 System Mode 2PARAMETER SET 5SENSOR ADJ RAM Clear 7IP Address A4.2 Overview A4.4 Self-Diagnostic Test A4.3 Reset Mode Ribbon type selection A4.4 Self-DiagnosticMaintenance counter/parameter settings print out Test Print head element check 2PAUSE63 Feed key 567 Cont Fine AdjustmentStrip Position Fine Adjustment A4.5 Printer Parameter $&.$-PP Back Feed Length Fine Adjustment Feed $-867PP A4.5 Printer Parameter X Axis Fine Adjustment Cont Thermal Direct Print PrintThermal Transfer Print 1Rewind$-!Motor 5%1Feed$-Motor% Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor Black Mark Sensor Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor Selection Print Condition SettingA4.6 Test Print Test Print menu contains the following Specifying the Print Condition for the Test Print Issue Count Setting Ribbon Type Selection Print Speed SettingSensor Type Selection Label Length Setting Issue Mode Selection Slant Line 3 dots Test Print Pattern SelectionPause key Slant Line 1 dot Factory Test BarcodeNon-Printing Auto Print $87235,17 755/$1 A4.7 Dump Mode A4.8 Additional Information A4.8.1 Self-Diagnostic Test Result Sample and Descriptions Sdram 8MB EXP.I/O Print Head Resistance Rank Table Total Feed ∙ Descriptions of the Maintenance Counter XON+READY Auto Busy A4.8.3 Magnified Views of Slant Line Pattern Appendix 5 Print Samples UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits CODE39 Full Ascii KIX Code MaxiCode UPC-A+2 digits UPC-A+5 digits Glossaries Pre-printed label Index Index