Issue Mode Selection, Label Length Setting | Toshiba B-492L, R-TH10

Strip mode

Batch mode

EO1-33032 A4.6 Test Print

APPENDIX 4 SYSTEM MODE

A4.6 Test Print (Cont.)	Issue Mode Selection
	Select the issue mode for the test print by selecting between “[S]
	NORMAL”7<3(>6@1250Batch mode)$/	and “[H] PEEL OFF” (Strip mode).

NOTE:

Press and hold the [RESTART] or [FEED] key to advance the values quickly and continuously. To stop, release the key.

[RESTART] 7<3(>61250+@3((/$2))/

[FEED]

After selecting/$%(//(1theIssuePPMode, press the [PAUSE] key to go to Label Length Setting.

Label Length Setting

Select the label length for the test print in a range from 5 mm to 999 mm.

[RESTART]

[FEED] /$%(//(1PP

NOTE:

When “PAPER FEED” is selected, the printer feeds the media to the correct print start position for the selected conditions.

When “PAPER NO FEED” is selected, the printer makes no pre-feed to set the print start position. If the print start position adjustment is unnecessary, Select "PAPER NO FEED" and save media.

[FEED] key:	Pressing the [FEED] key once causes a –1 mm
	change, down to 5 mm.

[RESTART]key: Pressing the [RESTART] key once causes a +1 mm

Paper Feed3$3(5)(('Selection

change, up to 999 mm.

After selecting the label length, press the [PAUSE] key to go to Paper Feed Selection.

Select whether or not a paper feed is performed.

[RESTART]	3$3(512)((')(('	Paper feed is
		available.
[FEED]		Paper feed is not
		Paper feed is not
		available.

After selecting the paper feed, press the [PAUSE] key. If "PAPER FEED" was selected the printer will feed the media. The display returns to the “<4>TEST PRINT”.

A4-17

Image 67

Toshiba B-492L, R-TH10 owner manual Issue Mode Selection, Label Length Setting

Contents

492L/R-TH10 Series For QQ For QP CE Compliance for EU only Wkhsoxj Request Regarding Maintenance Precautions Table of Contents Appendix 2 Messages and LED Unpacking Introduction FeaturesAccessories Product Overview Appearance of the Printer DimensionsType Type Side View Front View Operation Panel InteriorType Appearance of the Power Supply Unit Precautions Printer Setup Procedure before Operation Connecting the Cables to Your Printer Connecting the Power Cord Turning on the Printer Turning the PrinterTurning OFF the Printer Loading the Media Causing injury Paper Holder Media Guide Setting the black mark sensor position Setting the feed gap sensor position Strip mode Batch mode Loading the Media Loading the Ribbon Pcmcia Cards Inserting the Optional Pcmcia Cards Test Print Operation Panel On Line Mode To be printed Operation Cleaning MaintenancePrint Head/Platen Media Guide Plate/ Pinch Roller/Sensors Pinch Roller Feed Roller Paper Guide B Locking Screw Covers and Panels Paper Holder Care/Handling of the Media and Ribbon Restart key TroubleshootingError Messages Error Messages Problems/Causes Solutions Error Messages Problems/Cause Solutions Possible ProblemsPossible Problems Causes Solutions Removing Jammed Media Threshold Setting Threshold Setting Printer Operation Overview Installing the Printer Drivers Interface Driver InstallationSystem Requirements System Change to the Software License Agreement screen Cont Driver Installation Driver files copy will start Uninstalling the TEC B-492 Printer Driver Uninstalling the TEC B-492 Printer Driver A1.1 Printer Appendix 1 SpecificationsModel 492L/R-TH10-QQ 492L/R-TH10-QP Option Name Type Description Source A1.2 OptionsA1.3 Media A1.3.1 Media Type A1.3.2 Detection Area of the Transmissive Sensor A1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective Sensor A1.4 Ribbon Appendix 2 Messages and Leds Symbols in the message 53&$ „Interface Cables Appendix 3 Interface A4.1 Operation Panel Appendix 4 System Mode 2PARAMETER SET 5SENSOR ADJ RAM Clear 7IP Address A4.2 Overview A4.4 Self-Diagnostic Test A4.3 Reset Mode Ribbon type selection A4.4 Self-DiagnosticMaintenance counter/parameter settings print out Test Print head element check 2PAUSE63 Feed key 567 Cont Fine AdjustmentStrip Position Fine Adjustment A4.5 Printer Parameter $&.$-PP Back Feed Length Fine Adjustment Feed $-867PP A4.5 Printer Parameter X Axis Fine Adjustment Cont Thermal Transfer Print PrintThermal Direct Print 1Rewind$-!Motor 5%1Feed$-Motor% Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor Black Mark Sensor Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor Selection Print Condition SettingA4.6 Test Print Test Print menu contains the following Specifying the Print Condition for the Test Print Issue Count Setting Sensor Type Selection Print Speed SettingRibbon Type Selection Label Length Setting Issue Mode Selection Slant Line 3 dots Test Print Pattern SelectionPause key Slant Line 1 dot Non-Printing BarcodeFactory Test Auto Print $87235,17 755/$1 A4.7 Dump Mode A4.8 Additional Information A4.8.1 Self-Diagnostic Test Result Sample and Descriptions Sdram 8MB EXP.I/O Print Head Resistance Rank Table Total Feed ∙ Descriptions of the Maintenance Counter XON+READY Auto Busy A4.8.3 Magnified Views of Slant Line Pattern Appendix 5 Print Samples UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits CODE39 Full Ascii KIX Code MaxiCode UPC-A+2 digits UPC-A+5 digits Glossaries Pre-printed label Index Index