Test Print Pattern Selection, Pause key | Toshiba R-TH10, B-492L

APPENDIX 4 SYSTEM MODE	35,17&21',7,21		EO1-33032
			A4.6 Test Print

A4.6 Test Print (Cont.)	Test Print Pattern Selection
		35,&2',7,17
	With “<4>TEST PRINT” displayed after paper feed selection, press the
	[PAUSE] key.	&+$5$&7(56
	Select a test print pattern from the following options.
	[RESTART]	121%$5&2'(3	,1*
		6/$17/,1('27

6/$[FEED]17/,1('27$)872$&72<(6735,1775()/5$1

Slant Line (1 dot)

Print Sample of Slant Line (1 dot)

Print Sample of Slant Line (3 dots)

While displaying Slant Line (1 dot), press the [PAUSE] key to start printing6/the$17/,1(slant linepatterns'27(1 dot). After printing is completed, the display returns to “<4>TEST PRINT”.

Pressing the [PAUSE] key causes the display to show “SLANT LINE (1DOT)” again. Then, press the [FEED] key.

Slant Line (3 dots)

While displaying the Slant Line (3 dots), press the [PAUSE] key to start printing the slant line patterns (3 dots). After printing is completed, the display returns to “<4>TEST PRINT”.

Pressing the [PAUSE] key causes the display to show “SLANT LINE (3DOT)” again. Then, press the [FEED] key.

NOTE:

See A4.8.3 for further information.

A4-18

Image 68

Toshiba R-TH10, B-492L owner manual Test Print Pattern Selection, Pause key, Slant Line 1 dot, Slant Line 3 dots

Contents

492L/R-TH10 Series For QP CE Compliance for EU only For QQ Wkhsoxj Precautions Request Regarding Maintenance Table of Contents Appendix 2 Messages and LED Introduction Features AccessoriesProduct Overview Unpacking Type DimensionsAppearance of the Printer Front View Type Side View Type InteriorOperation Panel Appearance of the Power Supply Unit Printer Setup Precautions Procedure before Operation Connecting the Cables to Your Printer Connecting the Power Cord Turning OFF the Printer Turning the PrinterTurning on the Printer Causing injury Loading the Media Paper Holder Media Guide Setting the feed gap sensor position Setting the black mark sensor position Batch mode Strip mode Loading the Media Loading the Ribbon Pcmcia Cards Test Print Inserting the Optional Pcmcia Cards On Line Mode Operation Panel Operation To be printed Print Head/Platen MaintenanceCleaning Media Guide Plate/ Pinch Roller/Sensors Pinch Roller Feed Roller Paper Guide B Locking Screw Paper Holder Covers and Panels Care/Handling of the Media and Ribbon Troubleshooting Error MessagesError Messages Problems/Causes Solutions Restart key Possible Problems Causes Solutions Possible ProblemsError Messages Problems/Cause Solutions Threshold Setting Removing Jammed Media Threshold Setting Overview Installing the Printer Drivers Printer Operation Driver Installation System RequirementsSystem Interface Cont Change to the Software License Agreement screen Driver Installation Driver files copy will start Uninstalling the TEC B-492 Printer Driver Uninstalling the TEC B-492 Printer Driver Model 492L/R-TH10-QQ 492L/R-TH10-QP Appendix 1 SpecificationsA1.1 Printer A1.2 Options A1.3 MediaA1.3.1 Media Type Option Name Type Description Source A1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print Area A1.4 Ribbon Symbols in the message Appendix 2 Messages and Leds 53&$ Appendix 3 Interface „Interface Cables Appendix 4 System Mode A4.1 Operation Panel A4.2 Overview 2PARAMETER SET 5SENSOR ADJ RAM Clear 7IP Address A4.3 Reset Mode A4.4 Self-Diagnostic Test A4.4 Self-Diagnostic Maintenance counter/parameter settings print outTest Ribbon type selection Print head element check 2PAUSE63 567 Feed key Fine Adjustment Strip Position Fine AdjustmentA4.5 Printer Parameter Cont Back Feed Length Fine Adjustment $&.$-PP A4.5 Printer Parameter X Axis Fine Adjustment Cont Feed $-867PP Thermal Direct Print PrintThermal Transfer Print Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor 1Rewind$-!Motor 5%1Feed$-Motor% Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor Black Mark Sensor Print Condition Setting A4.6 Test PrintTest Print menu contains the following Selection Issue Count Setting Specifying the Print Condition for the Test Print Ribbon Type Selection Print Speed SettingSensor Type Selection Issue Mode Selection Label Length Setting Test Print Pattern Selection Pause keySlant Line 1 dot Slant Line 3 dots Factory Test BarcodeNon-Printing A4.7 Dump Mode Auto Print $87235,17 755/$1 A4.8.1 Self-Diagnostic Test Result Sample and Descriptions A4.8 Additional Information Sdram 8MB Print Head Resistance Rank Table EXP.I/O Total Feed ∙ Descriptions of the Maintenance Counter XON+READY Auto A4.8.3 Magnified Views of Slant Line Pattern Busy Appendix 5 Print Samples CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits UPC-A+2 digits UPC-A+5 digits KIX Code MaxiCode Glossaries Pre-printed label Index Index