Front View, Type Side View | Toshiba B-492L, R-TH10 guide

1. PRODUCT OVERVIEW

EO1-33032

1.5 Appearance of the Printer

1.5.2 Front View

Top Cover

Operation Panel

	Media Inlet
Supply Window
	Media Guide
[L Type]	[R Type]
1.5.3 Side View
Keyboard Interface	DC Power Connector
Connector
Serial Interface
Connector
(RS-232C)
PCMCIA Card
Slot (2 slots)

	Parallel Interface	Print Head
	Connector	Print Head
	Connector
	(Centronics)	Expansion I/O
		Expansion I/O
		Interface Connector

[L Type]

[R Type]

1- 3

Image 9

Toshiba B-492L, R-TH10 owner manual Front View, Type Side View

Contents

492L/R-TH10 Series For QQ For QP CE Compliance for EU only Wkhsoxj Request Regarding Maintenance Precautions Table of Contents Appendix 2 Messages and LED Accessories Introduction FeaturesProduct Overview Unpacking Dimensions Appearance of the PrinterType Type Side View Front View Interior Operation PanelType Appearance of the Power Supply Unit Precautions Printer Setup Procedure before Operation Connecting the Cables to Your Printer Connecting the Power Cord Turning the Printer Turning on the PrinterTurning OFF the Printer Loading the Media Causing injury Paper Holder Media Guide Setting the black mark sensor position Setting the feed gap sensor position Strip mode Batch mode Loading the Media Loading the Ribbon Pcmcia Cards Inserting the Optional Pcmcia Cards Test Print Operation Panel On Line Mode To be printed Operation Maintenance CleaningPrint Head/Platen Media Guide Plate/ Pinch Roller/Sensors Pinch Roller Feed Roller Paper Guide B Locking Screw Covers and Panels Paper Holder Care/Handling of the Media and Ribbon Error Messages TroubleshootingError Messages Problems/Causes Solutions Restart key Possible Problems Error Messages Problems/Cause SolutionsPossible Problems Causes Solutions Removing Jammed Media Threshold Setting Threshold Setting Printer Operation Overview Installing the Printer Drivers System Requirements Driver InstallationSystem Interface Change to the Software License Agreement screen Cont Driver Installation Driver files copy will start Uninstalling the TEC B-492 Printer Driver Uninstalling the TEC B-492 Printer Driver Appendix 1 Specifications A1.1 PrinterModel 492L/R-TH10-QQ 492L/R-TH10-QP A1.3 Media A1.2 OptionsA1.3.1 Media Type Option Name Type Description Source A1.3.2 Detection Area of the Transmissive Sensor A1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective Sensor A1.4 Ribbon Appendix 2 Messages and Leds Symbols in the message 53&$ „Interface Cables Appendix 3 Interface A4.1 Operation Panel Appendix 4 System Mode 2PARAMETER SET 5SENSOR ADJ RAM Clear 7IP Address A4.2 Overview A4.4 Self-Diagnostic Test A4.3 Reset Mode Maintenance counter/parameter settings print out A4.4 Self-DiagnosticTest Ribbon type selection Print head element check 2PAUSE63 Feed key 567 Strip Position Fine Adjustment Fine AdjustmentA4.5 Printer Parameter Cont $&.$-PP Back Feed Length Fine Adjustment Feed $-867PP A4.5 Printer Parameter X Axis Fine Adjustment Cont Print Thermal Transfer PrintThermal Direct Print 1Rewind$-!Motor 5%1Feed$-Motor% Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor Black Mark Sensor Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor A4.6 Test Print Print Condition SettingTest Print menu contains the following Selection Specifying the Print Condition for the Test Print Issue Count Setting Print Speed Setting Sensor Type SelectionRibbon Type Selection Label Length Setting Issue Mode Selection Pause key Test Print Pattern SelectionSlant Line 1 dot Slant Line 3 dots Barcode Non-PrintingFactory Test Auto Print $87235,17 755/$1 A4.7 Dump Mode A4.8 Additional Information A4.8.1 Self-Diagnostic Test Result Sample and Descriptions Sdram 8MB EXP.I/O Print Head Resistance Rank Table Total Feed ∙ Descriptions of the Maintenance Counter XON+READY Auto Busy A4.8.3 Magnified Views of Slant Line Pattern Appendix 5 Print Samples UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits CODE39 Full Ascii KIX Code MaxiCode UPC-A+2 digits UPC-A+5 digits Glossaries Pre-printed label Index Index