Appendix 5 Print Samples | Toshiba R-TH10, B-492L specs

APPENDIX 5 PRINT SAMPLES

EO1-33032

APPENDIX 5 PRINT SAMPLES

APPENDIX 5 PRINT SAMPLES

„Font

A5- 1

Image 78

Toshiba R-TH10, B-492L owner manual Appendix 5 Print Samples

Contents

492L/R-TH10 Series For QP CE Compliance for EU only For QQ Wkhsoxj Precautions Request Regarding Maintenance Table of Contents Appendix 2 Messages and LED Product Overview Introduction FeaturesAccessories Unpacking Dimensions Appearance of the PrinterType Front View Type Side View Interior Operation PanelType Appearance of the Power Supply Unit Printer Setup Precautions Procedure before Operation Connecting the Cables to Your Printer Connecting the Power Cord Turning the Printer Turning on the PrinterTurning OFF the Printer Causing injury Loading the Media Paper Holder Media Guide Setting the feed gap sensor position Setting the black mark sensor position Batch mode Strip mode Loading the Media Loading the Ribbon Pcmcia Cards Test Print Inserting the Optional Pcmcia Cards On Line Mode Operation Panel Operation To be printed Maintenance CleaningPrint Head/Platen Media Guide Plate/ Pinch Roller/Sensors Pinch Roller Feed Roller Paper Guide B Locking Screw Paper Holder Covers and Panels Care/Handling of the Media and Ribbon Error Messages Problems/Causes Solutions TroubleshootingError Messages Restart key Possible Problems Error Messages Problems/Cause SolutionsPossible Problems Causes Solutions Threshold Setting Removing Jammed Media Threshold Setting Overview Installing the Printer Drivers Printer Operation System Driver InstallationSystem Requirements Interface Cont Change to the Software License Agreement screen Driver Installation Driver files copy will start Uninstalling the TEC B-492 Printer Driver Uninstalling the TEC B-492 Printer Driver Appendix 1 Specifications A1.1 PrinterModel 492L/R-TH10-QQ 492L/R-TH10-QP A1.3.1 Media Type A1.2 OptionsA1.3 Media Option Name Type Description Source A1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print Area A1.4 Ribbon Symbols in the message Appendix 2 Messages and Leds 53&$ Appendix 3 Interface „Interface Cables Appendix 4 System Mode A4.1 Operation Panel A4.2 Overview 2PARAMETER SET 5SENSOR ADJ RAM Clear 7IP Address A4.3 Reset Mode A4.4 Self-Diagnostic Test Test A4.4 Self-DiagnosticMaintenance counter/parameter settings print out Ribbon type selection Print head element check 2PAUSE63 567 Feed key A4.5 Printer Parameter Fine AdjustmentStrip Position Fine Adjustment Cont Back Feed Length Fine Adjustment $&.$-PP A4.5 Printer Parameter X Axis Fine Adjustment Cont Feed $-867PP Print Thermal Transfer PrintThermal Direct Print Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor 1Rewind$-!Motor 5%1Feed$-Motor% Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor Black Mark Sensor Test Print menu contains the following Print Condition SettingA4.6 Test Print Selection Issue Count Setting Specifying the Print Condition for the Test Print Print Speed Setting Sensor Type SelectionRibbon Type Selection Issue Mode Selection Label Length Setting Slant Line 1 dot Test Print Pattern SelectionPause key Slant Line 3 dots Barcode Non-PrintingFactory Test A4.7 Dump Mode Auto Print $87235,17 755/$1 A4.8.1 Self-Diagnostic Test Result Sample and Descriptions A4.8 Additional Information Sdram 8MB Print Head Resistance Rank Table EXP.I/O Total Feed ∙ Descriptions of the Maintenance Counter XON+READY Auto A4.8.3 Magnified Views of Slant Line Pattern Busy Appendix 5 Print Samples CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits UPC-A+2 digits UPC-A+5 digits KIX Code MaxiCode Glossaries Pre-printed label Index Index