Toshiba RAV-SM1101BT-E, RAV-SM1400AT-E, RAV-SM1100AT-E, RAV-SM1401BT-E Contents Remarks

12-4. Display and Operation of Main Remote Controller and Central Control Remote Controller

1.Turn on all the power supplies of the air conditioner, and then turn on power of the central control remote controller (Line 16 RBC-SXC1P, Line 64 TCB-SC641). If both power supplies are simultaneously turned on or if they are turned on reversely, the check code [97] may be temporarily displayed on the central remote controller. When settings of connecting cables and central control address are correct, the connected air conditioner is displayed on the central control remote controller.

2.As shown in the following table, there is difference of LCD between main remote controller (RBC-AMT21) and the central control remote controller and also there are restriction and others of operation.

	Item		Contents			Cautions
		Main remote controller		Central control remote controller
1	Air volume selection	[SPEED]	[AUTO]	[VOL]	[AUTO]	Display of air speed selection differs.
			[HH]		[H]
			[H]		[M]
			[L]		[L]
		[SPEED]		[VOL]		In duct type
			[HH]		[FIX]	Air speed becomes [H] and [FIX].
2	Air speed selection	[SPEED]		[VOL]	[AUTO]	When handling main remote controller, [AUTO] is
	in FAN mode		[HH]		[H]	not displayed. If [AUTO] is selected at center side,
			[H]		[M]	[AUTO] is displayed on the main remote controller.
			[L]		[L]	In this time, the air speed becomes [HH].
3	Air speed selection	[SPEED]	[AUTO]	[VOL]	[AUTO]	On the central remote controller, only [AUTO] is
	in DRY mode		[HH]			displayed. The display on the main remote
			[H]			controller changes to [AUTO] by changing the
			[L]			setup temperature/louver, and the air speed is
						automatically selected.
4	Air direction	[SWING] and air		[LOUVER]		On the central remote controller, only [LOUVER] is
	adjustment	direction adjustment				displayed. It is displayed while flap is swinging,
						and the setup operation of [LOUVER] becomes
						selection of swing ON/OFF.
						To set up the air direction, use the main remote
						controller.
		(No display)		Manual operation for		In a model type without air direction adjustment
				[LOUVER]
5	Check button	Test run (4 seconds)		Check code display and		The function of long-pushing operation for the
				check reset (3 seconds)		check button differs. If the check reset operation
						on the central remote controller is performed
						during operation of air conditioner, the operation
						stops once, and then the operation restarts. (Error
						of air conditioner is cleared.)
6	Check code	3-digits display		2-digits display (alphabet		Display of check code differs.
		(alphabet + 2-digits		or numeral)		Ex. : Float switch operation
		numeral)				Main side: [P10]
						Center side: [0b]

3.When using the remote controller together with the former one (RBC-AM1, AT1), the display on the main remote controller differs if [Last-push priority/Center/Operation Prohibited] is selected from the central control remote controller.

		Contents
	Item			Remarks
		New remote controller	Former remote controller
		(RBC-AMT21)	(RBC-AM1, AT1)
1	Last-push priority	(No display)	(No display)	All the settings and ON/OFF operations are
				available.
2	Center	[CENTER] goes on	[CENTER] goes on	The setup contents on the central control remote
				controller are fixed, and only ON/OFF operation
				and timer setup operation are available on the
				main remote controller.
3	Operation prohib-		[CENTER] flashes	The setup contents on the central control remote
	ited			controller are fixed, and the air conditioner stops.
				Operation from the main remote controller is
				unavailable.

83