Installation | Zebra Technologies P1043301-005 specs

40

Installation

Install a Radio Card in a Wireless Print Server

5.Place the RF card cover over the wireless radio card, and secure it with a small screw.

Note • The S4M, ZM400, ZM600, RZ400, and RZ600 printers do not use the RF card cover.

3

2

1

1Clear plastic RF card cover (not used on all printers)

2Screw

3Compact Flash wireless radio card and adapter

6.Turn on (I) the printer.

The printer restarts and uses the wireless radio card to communicate with your WLAN. Allow several minutes for the printer to connect to the network. For more information about wireless status, refer to View Wireless Status through the Control Panel on page 52 or Troubleshooting the Wireless Print Server on page 139.

P1043301-005

11/21/13

Image 38

Zebra Technologies P1043301-005 manual Installation

Contents

ZebraNet Wired and Wireless Print Server User Guide Part Number P1043301-005 Contents Installation Getting Started ZebraLink WebView Using Printing ProtocolsPrinting Queues Print Server Web Pages Control Panel Hardware TroubleshootingFrequently Asked Questions 147 Glossary Index Contents About This Document Who Should Use This Document How This Document Is Organized Introduction on Document Conventions Ztools About This Document About This Document Introduction Overview Supported ServicesAddress Administration Protocols Support Supported Wireless Radio Cards Supported Security Types ZebraNet Wireless Plus Print Server Security Types Supported on the Wireless Plus Print Server Print Server ZebraNet Wireless Print Server Security Types Supported on the Wireless Print Server Printer Requirements Hardware Wired Print ServersWired Print Servers Available by Printer Hardware Wireless Print Servers Wireless Print Servers Available by Printer Zebra Part Numbers for ZebraNet Wireless Print Server Boards Memory Requirements Firmware 10/100 Print Server SN Yyyyyyy EN Zzzzzzzzzzzz Firmware Wireless Supported Firmware Versions ZT230 V72.18.X ZT410 V75.19.7Z ZT420 ZD500 V74.19.6Z Compatibility SpecificationsExternal ZebraNet 10/100 Print Server Specifications Internal ZebraNet 10/100 Print Server Specifications Wireless Print Server Specifications Introduction Installation Before You Begin To upgrade you printer firmware, complete these stepsExternal ZebraNet 10/100 Print Server Illustration External ZebraNet 10/100 Print Server Installation Instructions Rear of 105SL Printer Wireless Radio Card Wireless Print ServersInstall a Radio Card in a Wireless Print Server To install a wireless radio card, complete these steps Install a Radio Card in a Wireless Print Server Compact Flash Wireless Radio Card Installing a Compact Flash Wireless Radio Card Installation Getting Started Getting Started Before You Begin Default User ID and PasswordUser ID admin Password Label Width 211 63.5 150 127.00 Subnet Mask Default Gateway Serial Number You reach List Network From the control panel, enter Setup Mode. Refer to Not available on HC100 Getting Started Printer Configuration Wristband for HC100 Configuration of Wireless Securities Link Status Indicators View Wireless Status through the Control PanelLCD Link Status and Wireless Signal Indicators Wireless Signal Indicators Signal Strength HC100 Wireless Status Indicator Lights HC100 Wireless Status Indicator LightsZD500R Wired and Wireless Status Indicator Icons Yellow Flash Steady Green Flashing Green Determining the Active Print Server Viewing IP Addresses and the Active Print Server Active Device Selection PAX4 Skip WiredWireless Check Assigning an IP Address Without Dhcp via ZebraNet Bridge With Dynamic Host Configuration Protocol DhcpAssigning an IP Address on any Print Server Assigning an IP address Without Dhcp from the Control Panel 192.168.254.254 Assigning an IP Address Without Dhcp via a Telnet Session To use this method, complete these steps Gleaning Setting and Monitoring Alerts on Any Print Server ZebraLink Alerts ZebraLink Alerts and Destinations Using ZebraNet Bridge Using WebView Add Alert Checking Print Server Configuration Settings To access the print server settings, complete these steps Browser View Print Server Configuration Access Settings To enable protocols using WebView, complete these steps Enabling Protocols Print Server Configuration Protocol Configuration Defaulting ALL Print Servers Restore to Factory Defaults Using a ZPL Command Defaulting the Wireless Print Server on the S4M Defaulting the Print Servers on the ZM400 and ZM600 Printers Defaulting the Print Servers on the HC100 Printers Getting Started Getting Started Printing Queues Configuring the Print Queue Berkeley Software Distribution BSD-Style Print Queue Unix Configuration System V Queue InstallationConfiguring Operating System V Queue for ZebraNet Printing Prerequisites Printing Queues Using Printing Protocols IPP FTP To send information to the printer, perform these steps Using Printing Protocols ZebraLink WebView WebView Home To open the WebView of your printer, complete these steps View Printer Configuration Configuration Settings View and Modify Printer Settings To view and modify printer settings, complete these steps View and Modify Printer Settings View and Modify Printer Settings Menu Options General Setup Serial Communications Setup Network Communications Setup Print Listings on Label Rfid Setup Rfid Printers/Print Engines only Media Setup Calibration ZPL Control Advanced Setup 100 Click Network ConfigurationNetwork Communications Screens Click Submit Changes 101 Subscreens Network Communications SetupPrimary/Secondary Settings 102 X60.15.x and ZSPx 103 Wireless Setup Wireless Encryption Setup 104 To view the Directory Listing, complete these steps Directory Listing105 106 107 Create New Script Preview Label Reset108 Print Label Save As 109Save To view Printer Controls, complete these steps Printer Controls110 Print Server Web Pages 112 Print Server FeaturesStatus and Configuration Print Server Settings 113 114 115 Print Server Configuration Menu OptionsEnabled Protocols TCP/IP Configuration 116 System Snmp 117TCP/IP Logical Printing Ports 118 Smtp Email Alert ConfigurationWeb Admin POP3 Email Printing Output Port Configuration119 Print Server Status 120 121 To view the port status complete this step 122 ResetTo reset the print server, complete these steps Restore 123 124 Control Panel Control Panel Menu Options Wired Network Parameters on the LCDWired Network Parameters 126 127 Load LAN FROM? Reset Network 128 129 Wireless Network Parameters on the LCDWireless Network Parameters 130 Wlan Security Wireless Network Parameters 131 132 Hardware Troubleshooting 134 Troubleshooting the External 10/100 Print ServerResetting to Factory Defaults 135 Troubleshooting the External ZebraNet 10/100 Print ServerExternal ZebraNet 10/100 Print Server Issues and Solutions 136 Troubleshooting the Internal ZebraNet 10/100 Print Server 137 138 For the ZM400, ZM600, HC100, Xi4, and 105SLPlus Printers ZebraNet n Print Server Will Not Operate on the 5Ghz Band Troubleshooting the Wireless Print ServerResetting the Wireless Print Server to Factory Defaults 139 Ping the Printer ZebraNet Bridge Discovery or Configuration ProblemsUnable to Print 140 Telnet 141 Wireless Error Messages Unable to Configure DeviceHP JetAdmin or HP Web JetAdmin Error Messages 143 General Wireless IssuesGeneral Issues and Recommended Solutions 144 Encryption and Authentication Issues 145 146 IP IssuesIP Issues and Recommended Solutions Frequently Asked Questions FAQs 148 149 UDP Ports 150 Glossary 152 Lightweight Extensible Authentication Protocol 153 154 155 156 Index Index Not Associated message Not Authenticatd message Print server features WebView 112 print server status Radio Warning Poor Signal Index Index 164 Page Zebra Technologies Asia Pacific, LLC Zebra Technologies CorporationZebra Technologies Europe Limited ZIH Corp P1043301-005