Manuals / Zebra Technologies / Computer Equipment / All in One Printer

Zebra Technologies 11680100001, 14080100200, RXI4TM, 17080100200 manual Clean the Snap Plate, 124

Models: XI4TM RXI4TM 11680100201 22080100000 14080100000 11280100200 17280100000 14080100200 11680100001 22380100000 17080100000 11280100000 17080100200

1 190

Download 190 pages 49.35 Kb

Page 124

124

Routine Maintenance

Cleaning Schedule and Procedures

Clean the Snap Plate

Clean the snap plate when label adhesive or a label is stuck to the underside. Figure 20 shows the location of the snap plate. The snap plate is made of plastic in RFID printers and of metal in non-RFID printers.

Figure 20 • Snap Plate Location

Non-RFID Printers

Important • Be careful not to bend or twist the metal snap plate as you remove it from or insert it into the printer.

To clean a metal snap plate in a non-RFID printer, complete these steps:

1.Caution • Turn off (O) the printer and disconnect it from the power source before performing the following procedure.

Turn off (O) the printer, and disconnect the AC power cord and all data cables.

2.Caution • While performing any tasks near an open printhead, remove all rings, watches, hanging necklaces, identification badges, or other metallic objects that could touch the printhead.

Open the printhead and remove the media and ribbon (if used).

P1009874-002

Xi4™/RXi4™ User Guide

1/7/10

Image 124

Zebra Technologies 11680100001, 14080100200, RXI4TM, 17080100200, 22080100000, 17280100000 manual Clean the Snap Plate, 124

Contents

User Guide Part Number P1009874-002 Declaration of Conformity Xi4 Series 110Xi4, R110Xi4, 140Xi4, 170Xi4 FCC Compliance Statement Compliance InformationCanadian DOC Compliance Statement Contents Routine Maintenance 115 ConfigurationOperations Troubleshooting 133 Specifications 163 End User License Agreement Glossary Index Contents About This Document Who Should Use This Document How This Document Is Organized Contacts Mail Back Technical Library Document Conventions Icons Used Sample Figure with Callouts About This Document Introduction Printer Components Printer Components Control Panel Location of Control Panel Buttons and Lights LCD Printer Setup Before You Begin Storage Temperature and Humidity Handling the PrinterUnpack and Inspect the Printer Store the Printer Select a Site for the Printer Connections and Configuration The baud rate, number Select a Data Communication InterfaceData Communication Interfaces Limitations and Requirements Connections and Configuration No additional Twinax/Coax Optional Connections and Configuration Refer to the ZebraNet Configuration Refer to the ZebraNet Wireless User Guide for Data Cables and Wireless Cards Connect the Printer to a Power Source Power Cord Specifications Power Cord Specifications Install the Control Panel Keypad Cover Control Panel Keypad Cover Types of Media Radio frequency identification Rfid smart media-RFID Roll and Fanfold Media Non-ContinuousRoll Media Fanfold Media When to Use Ribbon Ribbon OverviewCoated Side of Ribbon To perform a media scratch test, complete these steps To perform an adhesive test, complete these steps To perform a ribbon scratch test, complete these steps Operations Print Modes and Printer Options Print Mode Descriptions and Printer RequirementsPrint Modes and Printer Options Media Paths Media Paths for Print Modes with Various Printer Options Cutter Prepare the Media for Loading Roll Media 110Xi4/R110Xi4 600 dpi 110Xi4/R110Xi4 200 dpi and 300 dpi Other Xi4 Models Fanfold Media To load fanfold media, complete these steps If using Then use this access slot Load Media in Tear-Off Mode Ribbon OUT error Operations Operations Load Media in Peel-Off Mode Media Loaded in Peel-Off Mode To set up the printer in Peel-Off mode, complete these steps Operations Ribbon OUT error Operations Operations Operations Load Media in Cutter Mode To set up the printer in Cutter mode, complete these steps Operations Ribbon OUT error Operations Operations Load Media in Rewind Mode Media Loaded in Rewind Mode To set up the printer in Rewind mode, complete these steps Operations Ribbon OUT error Operations Operations Operations Remove Media Liner from the Rewind Spindle Yes Operations Load Ribbon To load ribbon, complete these steps If… Then… Thread the ribbon over the media dancer assembly 1 and under Yes Operations Remove Used Ribbon To remove used ribbon, complete these steps Operations Calibrate the Printer Types of CalibrationAuto-calibration Long Calibration Sensor Profile CalibrationMedia and Ribbon Sensor Sensitivity Adjust Transmissive Media Sensors Upper Media Sensor Operations Operations To adjust the lower media sensor, complete these steps Lower Media Sensor Toggle Position Adjustment Adjust Printhead Pressure and Toggle PositionTo position the toggles, complete these steps Printhead Pressure Adjustment To adjust printhead pressure, complete these steps Operations Configuration Setup Mode Enter and Use Setup Mode Exit Setup Mode To leave Setup mode, complete these steps Default Password Value Change Password-Protected ParametersDisable the Password Protection Feature Print a Configuration Label To print a configuration label, complete these steps Print a Network Configuration Label To print a network configuration label, complete these steps Adjust Print Darkness Adjust Print SpeedStandard Control Panel Parameters Printer Parameters Sheet 1 Adjust the Tear-Off Position Default ValueSelect Print Mode Printer Parameters Sheet 2 Printer Parameters Sheet 3 Set Media TypeSet Sensor Type Select Print Method Set Print Width Printer Parameters Sheet 4Print Width Ranges and Maximum Values Default Value Disabled Printer Parameters Sheet 5Set Maximum Label Length Set Supplies Low Warning Set Early Warning for Maintenance Set Printhead Cleaning Interval for Early WarningReset Printhead Cleaning Counter for Early Warning Printer Parameters Sheet 6 Reset Printhead Life Counter for Early Warning View Non-Resettable CounterPrinter Parameters Sheet 7 Set Printhead Life for Early Warning Printer Parameters Sheet 8 List Network Settings Printer Parameters Sheet 9List All Initialize Flash Memory Printer Parameters Sheet 10 100Print Sensor Profile Default Value Bidirectional 101Printer Parameters Sheet 11 Calibrate Media and Ribbon Sensor Sensitivity 102 Printer Parameters Sheet 12 103 Printer Parameters Sheet 13 104 Printer Parameters Sheet 14Set Control Prefix Character Set Format Prefix Character Select ZPL Mode Default Value ZPLSelect Media Power-Up Option 105 Adjust Label Top Position 106Printer Parameters Sheet 16 Select Head Close Option Adjust Left Position 107Printer Parameters Sheet 17 Set the Head Test Count Default OFF Set Applicator Port Mode108 Printer Parameters Sheet 18 109 Printer Parameters Sheet 19 Set Reprint Mode See next column View Sensor Settings110 Printer Parameters Sheet 20 111 Printer Parameters Sheet 21 Default Value English 112Printer Parameters Sheet 22 Select the Display Language Additional Control Panel Parameters 113 114 Routine Maintenance Ordering Replacement Parts Replacing Printer ComponentsLubrication Recycling Printer Components Cleaning Schedule and Procedures Clean the ExteriorRecommended Printer Cleaning Schedule 117 Clean the Printhead and Platen Roller Clean the Media Compartment118 119 120 Clean the Sensors 121 122 Upper Media Sensor 123 Media Out Sensor Clean the Snap Plate 124 125 126 Rfid Printers 127 128 129 To clean the cutter, complete these steps Clean the Cutter130 Replace the Fuse To replace a faulty fuse, complete these steps131 132 Fuse Locations Troubleshooting Troubleshooting Checklists 134 LCD Error Messages LCD Error Messages135 136 Print Method on 137 138 139 Refer to the Maintenance Manual for 140 Print Quality Problems Print Quality Problems141 142 143 144 Bar code printedOn a label does not Scan Calibration Problems Calibration Problems145 Communications Problems Communications Problems146 Ribbon Problems Ribbon Problems147 Rfid Problems Rfid ProblemsRFID-enabled 148 149 150 Miscellaneous Printer Problems Miscellaneous Printer Problems151 152 Printer Diagnostics Power-On Self TestTo initiate the Power-On Self Test, complete these steps 153 To perform the Cancel Self Test, complete these steps Cancel Self Test154 155 Pause Self TestTo perform a Pause self test, complete these steps 156 Feed Self TestTo perform a Feed self test, complete these steps 157 Bar Code Darkness Comparison 158 Judging Bar Code Quality 159 Feed and Pause Self TestTo perform a Feed and Pause self test, complete these steps Communications Diagnostics Test 160 Sensor Profile 161 162 Specifications Features Standard FeaturesOptional Features 164 Bar Codes Zebra Programming Language ZPL165 General Specifications Physical SpecificationsElectrical Specifications 166 110Xi4 and R110Xi4 Print Specifications by Model167 140Xi4, 170Xi4, 168 Ribbon Specifications 169 Media Specifications 170 140Xi4, 170Xi4, and 220Xi4 Printers 171 172 140Xi4, 170Xi4, and 220Xi4 Black Mark Sensing End User License Agreement 174 175 176 177 178 Glossary Glossary Lightweight Extensible Authentication Protocol Glossary Index Numerics Index Index Index Rfid Wireless cards, 27 wireless print server characteristics Page Zebra Technologies Europe Limited Zebra Technologies CorporationZebra Technologies Asia Pacific, LLC