Zoom MRS-1044 Appendices, ■MIC ALGORITHM

Appendices

Effect type/parameter list

Explanation of MODULATION/DELAY MODULE parameters

Parameter name	Range	Explanation of parameter
DEPTH	0 – 10	Adjusts the depth of the effect.
RATE	1 – 30	Adjusts the speed of the effect.
MIX	0 – 30	Adjusts the mix amount of the effect.
FB	TYPE = FLANGER : -10 – 10	Adjusts the amount of feedback.
	TYPE = DELAY : 0 – 10
POSITION	AF / bF	Exchanges the effect locations of the DRIVE module and MOD module.
COLOR	1 – 4	Changes the type of the phase tone.
CLIP	0 – 10	Emphasizes the effect.
FREQ	TYPE = PDL-WAH : 1 – 50	Specifies the center frequency of the wah.
	TYPE = EXCITER : 1 – 5	Specifies the frequency.
LEVEL	1 – 8	Sets the output level of the module.
RTM	OFF / On	Specifies whether the expression pedal will be used as a wah pedal.
FLT TYPE	bPF / LPF	Specifies the type of filter.
RESO	1 – 10	Adds character to the sound.
SENS	-10 – 10	Adjusts the sensitivity with which the effect is applied.
SHIFT	-12.0 – 24.0	Sets the amount of shift produced by the pitch shifter.
TONE	0 – 10	Adjust the tone.
BALANCE	0 – 30	Adjusts the balance between the direct sound and effect sound.
LowBoost	0 – 10	Emphasizes the low-frequency range.
SIZE	1 – 10	Specifies the spatial width.
TIME	TYPE = WIDE : 1 – 64	Sets the delay time.
	TYPE = DELAY : 1 – 50
WET LVL	0 – 30	Adjusts the mix amount of the effect sound.
DRY LVL	0 – 30	Adjusts the mix amount of the direct sound.

■MIC ALGORITHM

COMP/LIM MODULE

TYPE	PARAMETER 1	PARAMETER 2	PARAMETER 3		PARAMETER 4	PARAMETER 5	PARAMETER 6
SINGLE	SENS	ATTACK	LEVEL		--	--	--
COMP x1	A mono input/output compressor.
SINGLE	THRSHOLD	RELEASE	LEVEL		--	--	--
LIMIITx1	A mono input/output limiter.
DUAL	SENS_1	ATTACK_1	LEVEL_1		SENS_2	ATTACK_2	LEVEL_2
COMP x2	A two-channel input/output compressor. Parameters for left and right can be set independently.
DUAL	THRSH_1	RELEASE1	LEVEL_1		THRES_2	RELEASE2	LEVEL_2
LIMIITx2	A two-channel input/output limiter. Parameters for left and right can be set independently.
Explanation of COMP/LIM MODULE parameters
Parameter name		Range			Explanation of parameter
SENS	SINGLE
SENS 1	DUAL ( Lch )	0 – 15		Adjusts the input sensitivity of compression.
SENS 2	DUAL ( Rch )
ATTACK	SINGLE
ATTACK_1	DUAL ( Lch )	0 – 15		Adjusts the speed at which compression is applied.
ATTACK_2	DUAL ( Rch )
THRSHLD	SINGLE
THRSH_1	DUAL ( Lch )	0 – 15		Adjusts the sensitivity at which the limiter begins to apply.
THRES_2	DUAL ( Rch )
RELEASE	SINGLE			Specifies the length from when the input signal level falls below the threshold until
RELEASE1	DUAL ( Lch )	0 – 15
				compression ends.
RELEASE2	DUAL ( Rch )
LEVEL	SINGLE
LEVEL_1	DUAL ( Lch )	1 – 8		Specifies the output level of the module.
LEVEL_2	DUAL ( Rch )

MIC PRE MODULE

TYPE	PARAMETER 1	PARAMETER 2	PARAMETER 3	PARAMETER 4	PARAMETER 5	PARAMETER 6
	COLOR	TONE	LEVEL	DE-ESSER	--	--
MIC PRE (*1)	A pre-amp for use with an external mic.
	COLOR 1	TONE 1	LEVEL 1	COLOR 2	TONE 2	LEVEL 2
MIC PRE (*2)	A pre-amp for use with an external mic.

*1: When a SINGLE type effect is selected for the COMP/LIM module

*2: When a DUAL type effect is selected for the COMP/LIM module

100

ZOOM MRS-1044