Intel IXP45X PCB Overview, General Recommendations, Component Selection, Component Placement

Page 59

General PCB Guide—Intel®IXP45X and Intel® IXP46X Product Line of Network Processors

4.0General PCB Guide

4.1PCB Overview

Beginning with components selection, this chapter presents general PCB guidelines. In cases where it is too difficult to adhere to a guideline, engineering judgment must be used. The methods are listed as simple DOs and DON’Ts.

This chapter does not discuss the functional aspects of any bus, or layout guides for any interfaced devices.

4.2General Recommendations

It is recommended that boards based on the IXP45X/IXP46X network processors employ a PCB stackup yielding a target impedance of 50 Ω ± 10% with 5 mil nominal trace width. That is, the impedance of the trace when not subjected to the fields created by changing current in neighboring traces.

When calculating flight times, it is important to consider the minimum and maximum impedance of a trace based on the switching of neighboring traces. Using wider spaces between the traces can minimize this trace-to-trace coupling. In addition, these wider spaces reduce cross-talk and settling time.

4.3Component Selection

•Do not use components faster than necessary

Clock rise (fall) time should be as slow as possible, as the spectral content of the waveform decreases

•Use components with output drive strength (slew-rate) controllable if available

•Use SMT components (not through-hole components) as through-hole (leaded) components have more stub inductance due to the protruding leads.

•Avoid sockets when possible

•Minimize number of connectors

4.4Component Placement

As shown in Figure 19 on page 60, when placing components, put:

•High-frequency components in the middle

•Medium-frequency around the high-frequency components

•Low-frequency components around the edge of the printed circuit board

	Intel® IXP45X and Intel® IXP46X Product Line of Network Processors
February 2007	HDD
Document Number: 305261; Revision: 004	59

Image 59

Contents February Hardware Design GuidelinesHDD Contents 12.1 Figures Tables Control Group Topology Transmission Line CharacteristicsDate Revision Description Revision HistoryHDD Chapter Name Description Content OverviewTitle Document # Related DocumentationTerm Explanation OverviewList of Acronyms and Abbreviations Smii Intel IXP465 Component Block Diagram Dslam Typical ApplicationsSystem Memory Map System Architecture DescriptionIntel IXP465 Example System Block Diagram Symbol Description Soft Fusible FeaturesSignal Type Definitions DDR Sdram Interface Pin Description Sheet 1 Signal InterfaceSoft Fusible Features DDR-266 Sdram InterfaceDdrircomp DDR Sdram Interface Pin Description Sheet 2Ddriwen DdrircveninnDDR Sdram Initialization Expansion BusDDR Sdram Memory Interface Input Pull Name Recommendations Output Down Reset Configuration StrapsExpansion Bus Signal Recommendations Name Function Description Boot/Reset Strapping Configuration Sheet 14 16-Bit Device Interface Boot/Reset Strapping Configuration Sheet 23 8-Bit Device Interface 5 32-Bit Device Interface Bit Device 16/32-Bit Device Interface Byte Enable Flash Interface Example Flash InterfaceDesign Notes Uart InterfaceSram Interface Name Input Pull Recommendations Output Down Uart Signal RecommendationsUart Interface Example MII/SMII InterfaceMII NPE B Signal Recommendations Sheet 1 Signal Interface MIIMII NPE a Signal Recommendations MII NPE C Signal Recommendations MII NPE B Signal Recommendations Sheet 2NPE A,B,C MAC Management Signal Recommendations NPE A,B,CDevice Connection, MII Smii Signal Recommendations NPE A, B, C Signal Interface, SmiiDevice Connection, Smii Gpio InterfaceGpio Signal Recommendations Device Connection I2C Signal RecommendationsI2C Interface I2C Eeprom Interface Example USB InterfaceUSB Host/Device Signal Recommendations Host Device USB Device Interface Example Utopia Level 2 InterfaceUtopia Signal Recommendations Utopia Interface Example HSS InterfaceHSSRXDATA0 High-Speed, Serial InterfaceHSSTXDATA0 HSSTXCLK0HSSRXCLK1 HSSTXDATA1HSSTXCLK1 HSSRXDATA1HSS Interface Example SSP InterfaceSynchronous Serial Peripheral Port Interface Input Pull Name Outpu Recommendations Down PCI InterfacePCI Controller Sheet 1 PCI Controller Sheet 2 PCI Interface Block DiagramPCI Interface Supporting 5 V PCI InterfacePCI Host/Option Interface Pin Description Sheet 1 PCI Option InterfacePCI Host/Option Interface Pin Description Sheet 2 PCI Host/Option Interface Pin Description Sheet 3 Jtag InterfaceClock Oscillator Clock SignalsClock Signals Input System ClockName Nominal Description Voltage PowerPower Interface Sheet 1 VCC De-Coupling Power SequenceReset Timing De-Coupling Capacitance RecommendationsHDD HDD Component Selection Component PlacementPCB Overview General RecommendationsStack-Up Selection Component Placement on a PCBControlled-impedance traces Low-impedance power distribution Layer Stackup General Layout Guidelines General Layout and Routing GuideGeneral Component Spacing Signal Changing Reference PlanesGood Design Practice for VIA Hole Placement Pad-to-Pad Clearance of Passive Components to a PGA or BGA Clock Signal ConsiderationsUSB Considerations Smii Signal ConsiderationsMII Signal Considerations EMI-Design Considerations Cross-TalkTrace Impedance Power and Ground PlaneHDD @66 MHz Electrical InterfaceTopology @33 MHzParameter Routing Guidelines Clock DistributionPCI Address/Data Routing Guidelines PCI Clock Routing Guidelines Trace Length LimitsRouting Guidelines Signal LoadingDDRIDQS40 DDR Signal GroupsGroup Signal Name Description No of Single Ended Signals IntroductionDDR Sdram HDD Clock Banks Memory Size Supported Memory ConfigurationsVTT VTT Terminating Circuitry Selecting VTT Power SupplyDdrmclk DDR Command and Control Setup and Hold ValuesSymbol Parameter Min Max Units DDR Data to DQS Read Timing Parameters DDR Data to DQS Write Timing Parameters DDR-Data-to-DQS-Write Timing ParametersPrinted Circuit Board Layer Stackup Printed Circuit Board Layer Stackup Printed Circuit Board Controlled ImpedancePrinted Circuit Board Controlled Impedance Timing Relationships Signal Group Absolute Minimum Absolute Maximum LengthTiming Relationships Clock Group Resistive Compensation Register RcompDDRIBA10, DDRIRASN, DDRICASN, Ddriwen Clock Signal Group Routing GuidelinesData, Command, and Control Group Routing Guidelines Parameter DefinitionTransmission Line Length Clock Group Topology Transmission Line CharacteristicsSimulation Results Clock GroupDDR Clock Topology Two-Bank x16 Devices DDR Clock Simulation Results Two-Bank x16 Devices Data GroupData Group Topology Transmission Line Characteristics DDR Data Topology Two-Bank x16 Devices DDR Data Write Simulation Results Two-Bank x16 Devices HDD HDD Control Group Control Group Topology Transmission Line CharacteristicsDDR RAS Simulation Results Two-Bank x16 Devices Command Group Topology Transmission Line Characteristics Command GroupDDR Command MA3 Topology Two-Bank x16 Devices DDR Address Simulation Results Two-Bank x16 Devices DDR Command RAS Topology Two-Bank x16 Devices 104 DDR RCVENIN/RCVENOUT Topology Rcvenin and RcvenoutDDR RCVENIN/RCVENOUT Simulation Results Rseries = 0 Ω DDR RCVENIN/RCVENOUT Simulation Results Rseries = 60 Ω 108