Pioneer DJM-400 Effect Parameters, To Playback a Recorded Sample, Erasing a Recorded Sample

Page 12

EFFECT FUNCTIONS (IN-LOOP SAMPLER/EFFECT PARAMETERS)

4.Set the ON/OFF button to ON.

5.At the point you wish to sample record, press one of the non-lighted BEAT/BANK buttons.

Lighted BEAT/BANK buttons have already been recorded, and cannot be used again unless their recorded contents are erased.

Recording begins automatically when the sound signal from CD player or other component is detected. During recording, the BEAT/BANK button will flash quickly. During recording standby, the button will flash slowly at intervals.

When 4 beats of sound at the measured BPM have been recorded, the BEAT/BANK button flashes slowly and loop play is performed.

6.If the beat becomes unsynchronized, press one of the BEAT/PITCH buttons (–, +) to resynchronize the timing of the playback sample to the currently playing track.

The playback speed increases while the [+] button is depressed, and decreases while the [–] button is depressed.

7.Rotate the LEVEL/DEPTH dial to adjust the sound balance between source and sample.

8.To stop loop playback, press the corresponding BEAT/ BANK button.

The BEAT/BANK button indicator will change from slow flashing to steadily lighted.

[To Playback a Recorded Sample]

1Set the effect selector switch to [IN-LOOP SAMPLER].

2 Use the effect channel selector to choose the channel for loop playback.

3 Set the ON/OFF button to ON.

4 Press the BEAT/BANK button containing the sample you wish to play as a loop.

The BEAT/BANK buttons with recorded samples are lighted.

The selected button will flash slowly and loop play will begin.

5 If the beat becomes unsynchronized, press one of the

BEAT/PITCH buttons (–, +) to resynchronize the timing of the playback sample to the currently playing track.

The playback speed increases while the [+] button is depressed, and decreases while the [–] button is depressed.

6Rotate the LEVEL/DEPTH dial to adjust the sound balance

between source and sample.

7To stop loop playback, press the corresponding BEAT/ BANK button.

The BEAT/BANK button indicator will light steadily.

[Erasing a Recorded Sample]

1Set the effect selector to [IN-LOOP SAMPLER].

2While holding the ERASE (BEAT/PITCH –) button depressed, press the BEAT/BANK button containing the sample you wish to erase.

The BEAT/BANK buttons containing recorded samples are lighted.

The indicator in the selected BEAT/BANK button will go out and the sample will be erased.

8. IN-LOOP SAMPLER

This function allows you to store 4-beat sounds in up to 5 banks, then output them repeatedly.

Example

Bank 1

Present track BPM=125

Repeat

Bank 1 ON

EFFECT PARAMETERS

 

Name

BEAT/BANK button parameters

 

Parameter 1 (BEAT button)

Parameter 2

 

Contents

Setting Range (unit)

(LEVEL/DEPTH dial)

 

 

 

1

DELAY

Sets delay time of 1/2 to 4/1 per 1

Sets delay time.

1 to 8 000 (ms)

Sets balance between original and

 

 

beat of BPM time.

 

 

 

 

 

 

delay sound.

2

ECHO

Sets delay time of 1/2 to 4/1 per 1

Sets delay time.

1 to 8 000 (ms)

Sets balance between original

 

 

beat of BPM time.

 

 

 

 

 

 

sound and echo sound.

 

 

 

 

 

 

 

 

 

 

3

FILTER

Cycle of cutoff frequency shift is set

Sets cycle for

10 to 32 000 (ms)

Amount of effect increases when

 

 

in unit of 1/1 to 16/1 relative to 1

cutoff time shift.

 

 

 

dial is turned clockwise.

 

 

beat of BPM.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

FLANGER

Cycle of flanger shift is set in units

Sets cycle for

10 to 32 000 (ms)

Amount of effect increases when

 

 

of 1/1 to 16/1 relative to 1 beat of

flanger effect

 

 

 

dial is turned clockwise. When dial

 

 

BPM.

shift.

 

 

 

is turned fully counterclockwise,

 

 

 

 

 

 

 

 

 

only original sound is output.

 

 

 

 

 

 

 

 

 

 

5

PHASER

Cycle of phaser effect shift is set in

Sets cycle for

10 to 32 000 (ms)

Amount of effect increases when

 

 

units of 1/1 to 16/1 relative to 1 beat

phase effect shift.

 

 

 

dial is turned clockwise. When dial

 

 

of BPM.

 

 

 

 

 

 

is turned fully counterclockwise,

 

 

 

 

 

 

 

 

 

only original sound is output.

 

 

 

 

 

 

 

 

 

 

6

ROBOT

Robot sound effects can be set in 7

Set robot sound

–100, –66, –50, 0,

Amount of effect increases when

 

 

fixed values from –100 % to +100 %.

effect.

+26, +50, +100 (%)

dial is turned clockwise.

 

 

 

 

 

 

(fixed values)

 

 

 

 

 

 

 

 

 

 

 

7

ROLL

Sets effect time of 1/2 to 4/1 per 1

Sets effect time.

10 to 8 000 (ms)

Sets balance of original sound and

 

 

beat of BPM time.

 

 

 

 

 

 

ROLL sound. No change is produced

 

 

 

 

 

 

 

 

 

when dial is turned toward the right

 

 

 

 

 

 

 

 

 

side of the center position.

8

IN-LOOP SAMPLER

Selects bank for recording/playback

 

 

 

 

 

 

Sets balance of original sound and

 

 

of 4 beat source.

 

 

 

 

 

 

recorded sample. No change is

 

 

 

 

 

 

 

 

 

produced when dial is turned

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

toward the right side of the center

 

 

 

 

 

 

 

 

 

position.

 

 

 

 

 

 

 

 

 

 

12

<DRB1404> En

Page 11 Page 13
Image 12
Page 11 Page 13
Contents DJM-400 Cleaning the Unit POWER-CORD CautionLocation Important the Moulded PlugContents FeaturesConnections Connection PanelRear panel Front panelConnecting Inputs Connecting OutputsConnecting the Power Cord EnglishNames and Functions of Parts Names and Functions of PartsFader Start Bank CH. Select 1/2/MIC/MASTERMixer Operations Basic OperationsUsing the Cross Fader to Start Playback Using the Channel Fader to Start PlaybackFader Start Function Mixer Operations Fader Start FunctionEffect Functions Types of Beat EffectsUsing the TAP Button for Manual BPM Input Using the BEAT/PITCH buttons for Manual BPM InputProducing Beat Effects IN-LOOP SamplerEffect Parameters To Playback a Recorded SampleErasing a Recorded Sample Effect Functions IN-LOOP SAMPLER/EFFECT ParametersTroubleshooting TroubleshootingSymptom Possible Cause Remedy ThruEmplacement Avertissements Concernant L’USAGENettoyer l’appareil AvertissementTable DES Matières CaractéristiquesAvant L’UTILISATION UtilisationBranchements Panneau DE ConnexionPanneau arrière Panneau avantBranchement DES Entrées Branchements DE SortieFrançais Noms ET Fonctions DES Organes Noms ET Fonctions DES OrganesDELAY/ECHO/FILTER/FLANGER/PHASER ROBOT/ROLL/IN-LOOP Sampler Master LevelUtilisation DU Mixeur Démarches DE BaseFonction DE Départ EN Fondu Sélection de la courbe de fondu croiséLancement de la lecture par fondu croisé Lancement de la lecture par fondu de canalFonctions DES Effets Types D’EFFETS DE BattementFonctions DES Effets Types D’EFFETS DE Battement Production D’EFFETS DE Battement Échantillonneur D’ENTRÉE DE BoucleUtilisation du bouton TAP pour une saisie BPM manuelle Paramètres DES Effets Lecture d’un échantillon enregistréEffacement d’un échantillon enregistré Symptômes Causes possibles Corrections Master LevelVorsichtshinweise ZUR Handhabung WichtigAufstellung Reinigen des GerätesInhaltsverzeichnis Technische DatenMerkmale Anschlüsse Rückwand FrontplatteAnschlüsse Anschlüsse AN DEN Eingangsbuchsen DeutschAnschlüsse AN DEN Ausgangsbuchsen Anschliessen DES NetzkabelsMaster-Ausgang KopfhörerBezeichnung UND Funktion DER Bedienelemente FLANGER/PHASER/ROBOT/ROLL/IN-LOOP Sampler Bedienung DES Mischpults Grundlegende BedienungsverfahrenFADER-STARTFUNKTION Starten der Wiedergabe über Kanal-FaderhebelBedienung DES Mischpults FADER-STARTFUNKTION Wiedergabestart und Cue-Rücklauf über Kreuz-FaderhebelEffektfunktionen BEAT-EFFEKTTYPENEffektfunktionen BEAT-EFFEKTTYPEN Erzeugen VON BEAT-EFFEKTEN Effektfunktionen Erzeugen VON BEAT-EFFEKTENGebrauch der TAP-Taste für manuelle Eingabe des BPM-Wertes EINGANGSSCHLEIFEN-SAMPLER Wiedergabe eines aufgezeichneten SampleLöschen eines aufgezeichneten Sample Effektfunktionen EINGANGSSCHLEIFEN-SAMPLEREffektparameter Effektfunktionen EffektparameterBezeichnung Parameter 1 BEAT-Taste FunktionStörungsbeseitigung StörungsbeseitigungStörung Mögliche Ursache Abhilfemaßnahme Avvertenze PER L’USO ImportantePosizionamento Pulizia dell’apparecchioCaratteristiche Prima DELL’USOOperazioni Altri DatiCollegamenti Pannello DEL CollegamentiPannello posteriore Pannello anterioreCollegamento Degli Ingressi Collegamenti DI UscitaCollegamento DEL Cavo DI Alimentazione ItalianoNome Delle Varie Parti E Loro Funzione Nome Delle Varie Parti E Loro FunzioneSelettore d’ingresso del canale Manopola di regolazione TrimIndicatori del livello di uscita principale Pulsante/indicatore di effetto ON/OFFPulsante/indicatore della modalità di misurazione BPM Auto Selettore di effetti DELAY/ECHO/FILTEROperazioni COL Mixer Operazioni DI BaseInizio della riproduzione con la dissolvenza incrociata Inizio della riproduzione con la dissolvenza dei canaliOperazioni COL Mixer Funzione DI Inizio Della Dissolvenza Funzioni DI Effetto Tipi DI Effetti RitmiciFunzioni DI Effetto Tipi DI Effetti Ritmici Produzione DI Effetti DI Ritmo Campionatore DI CicliGirando la manopola LEVEL/DEPTH si regola il parametro Quantitativo dell’effetto sceltoCancellazione di un campione Parametri Degli EffettiRiproduzione di un campione registrato Diagnostica Funzioni DI Effetto Parametri Degli Effetti / DiagnosticaProblema Causa possibile Rimedio Installatieplek Waarschuwingen I.V.M. HET GebruikBelangrijk Het toestel schoonmakenInhoudsopgave KenmerkenVoor Gebruik BedieningAchterpaneel Voorpaneel Aansluiten VAN Apparatuur OP DE IngangenAansluiten VAN Apparatuur OP DE Uitgangen Aansluiten VAN HET NetsnoerBenaming EN Functie VAN DE Bedieningsorganen Hoofdniveau-indicators Master Level BPM meetmethodetoets/indicator AutoEffecttoets/indicator ON/OFF Hoofduitvoer-niveauregelaar Master LevelBediening VAN HET Mengpaneel BasisbedieningFaderstartfunctie Kiezen van de kruisfadercurveGebruik van de kruisfader om te starten met afspelen Gebruik van de kanaalfader om te starten met afspelenEffectfuncties Typen BEAT-EFFECTENEffectfuncties Typen BEAT-EFFECTEN BEAT-EFFECTEN Produceren Effectfuncties BEAT-EFFECTEN PRODUCEREN/IN-LOOP SamplerZet de ON/OFF toets op on om het gekozen effect in te SchakelenEffectparameters Weergeven van een opgenomen sampleWissen van een opgenomen sample Effectfuncties IN-LOOP SAMPLER/EFFECTPARAMETERSVerhelpen VAN Storingen Effectfuncties Effectparameters / Verhelpen VAN StoringenStoring Mogelijke oorzaak Maatregelen LevelPrecauciones Para LA Manipulación SituaciónLimpieza de la unidad AdvertenciaÍndice EspecificacionesCaracterísticas ÑolConexiones Panel DE ConexionesPanel posterior Panel frontalConexiones DE LAS Entradas Conexiones DE SalidaEspañol Nomenclatura Y Funciones DE LOS Controles Nomenclatura Y Funciones DE LOS ControlesSelector de entrada del canal Control de ajuste del nivel de entrada TrimControl deslizante de fundido cruzado Indicadores del nivel principal Master LevelControl del nivel de salida principal Master Level Sección de efectos de compás Visualizador del valor de BPMOperaciones DE LA Consola DE Mezcla Operaciones BásicasFunción DE Inicio CON Fundido Empleo del fundido cruzado para iniciar la reproducciónEmpleo del fundido de canales para iniciar la reproducción Funciones DE LOS Efectos Tipos DE Efectos DE CompásFunciones DE LOS Efectos Tipos DE Efectos DE Compás Producción DE Efectos DE Compás Entrada manual de BPM empleando el botón TAPEntrada manual de BPM empleando los botones BEAT/PITCHParámetros DE LOS Efectos Para reproducir una muestra grabadaBorrado de una muestra grabada BEAT/BANKSolución DE Problemas Síntoma Causa posible SoluciónDSP

DJM-400 specifications

The Pioneer DJM-400 mixer is a compact yet powerful addition to any DJ's setup, designed to blend professional capabilities with ease of use. As a two-channel mixer, it provides a perfect balance between features and simplicity, making it ideal for both beginner and experienced DJs.

One of the standout features of the DJM-400 is its high-quality sound output. The mixer is equipped with 48 kHz/24-bit digital signal processing, ensuring crystal-clear audio quality. This level of fidelity is crucial for DJs who want to deliver a party experience that is both immersive and engaging.

The DJM-400 includes a built-in sound card for seamless digital connectivity. This allows DJs to connect to a computer or laptop easily, enabling them to use software like Serato or Traktor. The mixer supports multiple formats and offers USB connectivity, which means it can also be used with a wide variety of devices. Its plug-and-play design minimizes setup time, letting DJs focus on their performance rather than technical issues.

Another noteworthy characteristic is the integrated digital effects processor. The DJM-400 features a range of built-in effects, including delay, echo, and flanger, which can be applied to individual channels, allowing DJs to add depth and dimension to their mixes. The effects can be manipulated using intuitive controls, making it easy to create unique sounds on the fly.

The layout of the DJM-400 has been thoughtfully designed to facilitate quick and easy adjustments. The EQ section features three-band equalizers for each channel, allowing precise control over bass, midrange, and treble frequencies. This empowers DJs to tailor their sound according to the venue and crowd.

Moreover, the DJM-400 comes with a crossfader that is exceptionally smooth, enabling seamless transitions between tracks. The fader is also replaceable, ensuring longevity and catering to individual preferences in performance style.

In summary, the Pioneer DJM-400 is a highly capable mixer that combines excellent sound quality, advanced technology, and user-friendly design. The inclusion of a built-in sound card, a suite of digital effects, and an intuitive layout makes it a versatile choice for DJs of all skill levels. Whether you're just starting your DJ journey or you're a seasoned professional, the DJM-400 delivers the features needed to elevate your performances and connect with your audience.
Top Page Image Contents