Pioneer DJM-400 operating instructions Troubleshooting, Symptom Possible Cause Remedy, Thru

Page 13

TROUBLESHOOTING

TROUBLESHOOTING

Incorrect operations are often mistaken for trouble and malfunctions. If you think there is something wrong with this component, check the points below. Sometimes the trouble may originate from another component. Thus, also check the other electrical appliances also in use.

If the trouble cannot be rectified even after checking the following items, contact your dealer or nearest PIONEER service center.

Symptom

Possible Cause

Remedy

 

 

 

No power

÷ The power cord is not connected.

÷ Connect to power outlet.

 

 

 

No sound, or sound volume is too

÷ Input selector switch is set incorrectly.

÷ Set input selector to playback component.

low.

÷ PHONO/LINE input selector switch is set

÷ Set the PHONO/LINE input selector to the

 

incorrectly.

component being played.

 

÷ Connection cables are connected

÷ Connect correctly.

 

incorrectly, or connections are loose.

 

 

÷ Jacks or plugs are dirty.

÷ Clean soiled jacks/plugs before connecting.

 

 

 

Sound is distorted.

÷ Master output level is too high.

÷ Adjust master output level (MASTER LEVEL)

 

 

dial.

 

÷ Input level is too high.

÷ Adjust the TRIM dial so that the input level

 

 

approaches 0 dB on the channel level

 

 

indicator.

Cross fader doesn’t work.

÷ Cross fader selector switch is set to

÷ Correctly set the switch to a setting other than

 

[THRU].

[THRU].

 

 

 

Can’t perform fader start with CD

÷ The FADER START button is set to OFF.

÷ Set the FADER START button to ON.

player.

÷ Rear panel CONTROL jack is not connected

÷ Use a control cable to connect the CONTROL

 

to CD player.

jacks of DJM-400 and CD player.

 

÷ Only the rear panel CONTROL jack is

÷ Connect both the CONTROL jacks and CD

 

connected to the CD player.

input connectors.

 

 

 

Effects don’t work.

÷ Effect channel selector (CH. SELECT)

÷ Correctly select the channel on which you

 

setting is incorrect.

wish to apply effects.

 

÷ Effect parameter adjust dial (LEVEL/

÷ Adjust the effect parameter adjust dial.

 

DEPTH) is set to [MIN].

 

 

 

 

BPM can’t be measured.

÷ Input level is set too high, or too low.

÷ Adjust the TRIM dial.

Measured BPM value is incorrect.

÷ BPM may not be correctly measurable with

÷ Strike the TAP button to set BPM manually.

 

some tracks.

 

The measured BPM value is

÷ Some differences may occur due to

÷ No remedy is necessary.

different from the value published

differences in BPM detection methods.

 

with the CD.

 

 

 

 

 

Static electricity or other external interference may cause the unit to malfunction. To restore normal operation, turn the power off and then on again.

English

Published by Pioneer Corporation. Copyright © 2006 Pioneer Corporation. All rights reserved.

13

<DRB1404> En

Image 13
Contents DJM-400 POWER-CORD Caution Cleaning the UnitLocation Important the Moulded PlugFeatures ContentsConnection Panel ConnectionsRear panel Front panelConnecting Outputs Connecting InputsConnecting the Power Cord EnglishNames and Functions of Parts Names and Functions of PartsFader Start CH. Select 1/2/MIC/MASTER BankBasic Operations Mixer OperationsUsing the Channel Fader to Start Playback Using the Cross Fader to Start PlaybackFader Start Function Mixer Operations Fader Start FunctionTypes of Beat Effects Effect FunctionsUsing the BEAT/PITCH buttons for Manual BPM Input Using the TAP Button for Manual BPM InputProducing Beat Effects IN-LOOP SamplerTo Playback a Recorded Sample Effect ParametersErasing a Recorded Sample Effect Functions IN-LOOP SAMPLER/EFFECT ParametersTroubleshooting TroubleshootingSymptom Possible Cause Remedy ThruAvertissements Concernant L’USAGE EmplacementNettoyer l’appareil AvertissementCaractéristiques Table DES MatièresAvant L’UTILISATION UtilisationPanneau DE Connexion BranchementsPanneau arrière Panneau avantBranchements DE Sortie Branchement DES EntréesFrançais Noms ET Fonctions DES Organes Noms ET Fonctions DES OrganesMaster Level DELAY/ECHO/FILTER/FLANGER/PHASER ROBOT/ROLL/IN-LOOP SamplerDémarches DE Base Utilisation DU MixeurSélection de la courbe de fondu croisé Fonction DE Départ EN FonduLancement de la lecture par fondu croisé Lancement de la lecture par fondu de canalTypes D’EFFETS DE Battement Fonctions DES EffetsFonctions DES Effets Types D’EFFETS DE Battement Échantillonneur D’ENTRÉE DE Boucle Production D’EFFETS DE BattementUtilisation du bouton TAP pour une saisie BPM manuelle Lecture d’un échantillon enregistré Paramètres DES EffetsEffacement d’un échantillon enregistré Master Level Symptômes Causes possibles CorrectionsWichtig Vorsichtshinweise ZUR HandhabungAufstellung Reinigen des GerätesTechnische Daten InhaltsverzeichnisMerkmale Rückwand Frontplatte AnschlüsseAnschlüsse Deutsch Anschlüsse AN DEN EingangsbuchsenAnschliessen DES Netzkabels Anschlüsse AN DEN AusgangsbuchsenMaster-Ausgang KopfhörerBezeichnung UND Funktion DER Bedienelemente FLANGER/PHASER/ROBOT/ROLL/IN-LOOP Sampler Grundlegende Bedienungsverfahren Bedienung DES MischpultsStarten der Wiedergabe über Kanal-Faderhebel FADER-STARTFUNKTIONBedienung DES Mischpults FADER-STARTFUNKTION Wiedergabestart und Cue-Rücklauf über Kreuz-FaderhebelBEAT-EFFEKTTYPEN EffektfunktionenEffektfunktionen BEAT-EFFEKTTYPEN Effektfunktionen Erzeugen VON BEAT-EFFEKTEN Erzeugen VON BEAT-EFFEKTENGebrauch der TAP-Taste für manuelle Eingabe des BPM-Wertes Wiedergabe eines aufgezeichneten Sample EINGANGSSCHLEIFEN-SAMPLERLöschen eines aufgezeichneten Sample Effektfunktionen EINGANGSSCHLEIFEN-SAMPLEREffektfunktionen Effektparameter EffektparameterBezeichnung Parameter 1 BEAT-Taste FunktionStörungsbeseitigung StörungsbeseitigungStörung Mögliche Ursache Abhilfemaßnahme Importante Avvertenze PER L’USOPosizionamento Pulizia dell’apparecchioPrima DELL’USO CaratteristicheOperazioni Altri DatiPannello DEL Collegamenti CollegamentiPannello posteriore Pannello anterioreCollegamenti DI Uscita Collegamento Degli IngressiCollegamento DEL Cavo DI Alimentazione ItalianoNome Delle Varie Parti E Loro Funzione Nome Delle Varie Parti E Loro FunzioneSelettore d’ingresso del canale Manopola di regolazione TrimPulsante/indicatore di effetto ON/OFF Indicatori del livello di uscita principalePulsante/indicatore della modalità di misurazione BPM Auto Selettore di effetti DELAY/ECHO/FILTEROperazioni DI Base Operazioni COL MixerInizio della riproduzione con la dissolvenza dei canali Inizio della riproduzione con la dissolvenza incrociataOperazioni COL Mixer Funzione DI Inizio Della Dissolvenza Tipi DI Effetti Ritmici Funzioni DI EffettoFunzioni DI Effetto Tipi DI Effetti Ritmici Campionatore DI Cicli Produzione DI Effetti DI RitmoGirando la manopola LEVEL/DEPTH si regola il parametro Quantitativo dell’effetto sceltoParametri Degli Effetti Cancellazione di un campioneRiproduzione di un campione registrato Funzioni DI Effetto Parametri Degli Effetti / Diagnostica DiagnosticaProblema Causa possibile Rimedio Waarschuwingen I.V.M. HET Gebruik InstallatieplekBelangrijk Het toestel schoonmakenKenmerken InhoudsopgaveVoor Gebruik BedieningAchterpaneel Voorpaneel OP DE Ingangen Aansluiten VAN ApparatuurAansluiten VAN Apparatuur OP DE Uitgangen Aansluiten VAN HET NetsnoerBenaming EN Functie VAN DE Bedieningsorganen BPM meetmethodetoets/indicator Auto Hoofdniveau-indicators Master LevelEffecttoets/indicator ON/OFF Hoofduitvoer-niveauregelaar Master LevelBasisbediening Bediening VAN HET MengpaneelKiezen van de kruisfadercurve FaderstartfunctieGebruik van de kruisfader om te starten met afspelen Gebruik van de kanaalfader om te starten met afspelenTypen BEAT-EFFECTEN EffectfunctiesEffectfuncties Typen BEAT-EFFECTEN Effectfuncties BEAT-EFFECTEN PRODUCEREN/IN-LOOP Sampler BEAT-EFFECTEN ProducerenZet de ON/OFF toets op on om het gekozen effect in te SchakelenWeergeven van een opgenomen sample EffectparametersWissen van een opgenomen sample Effectfuncties IN-LOOP SAMPLER/EFFECTPARAMETERSEffectfuncties Effectparameters / Verhelpen VAN Storingen Verhelpen VAN StoringenStoring Mogelijke oorzaak Maatregelen LevelSituación Precauciones Para LA ManipulaciónLimpieza de la unidad AdvertenciaEspecificaciones ÍndiceCaracterísticas ÑolPanel DE Conexiones ConexionesPanel posterior Panel frontalConexiones DE Salida Conexiones DE LAS EntradasEspañol Nomenclatura Y Funciones DE LOS Controles Nomenclatura Y Funciones DE LOS ControlesSelector de entrada del canal Control de ajuste del nivel de entrada TrimIndicadores del nivel principal Master Level Control deslizante de fundido cruzadoControl del nivel de salida principal Master Level Sección de efectos de compás Visualizador del valor de BPMOperaciones Básicas Operaciones DE LA Consola DE MezclaEmpleo del fundido cruzado para iniciar la reproducción Función DE Inicio CON FundidoEmpleo del fundido de canales para iniciar la reproducción Tipos DE Efectos DE Compás Funciones DE LOS EfectosFunciones DE LOS Efectos Tipos DE Efectos DE Compás Entrada manual de BPM empleando el botón TAP Producción DE Efectos DE CompásEntrada manual de BPM empleando los botones BEAT/PITCHPara reproducir una muestra grabada Parámetros DE LOS EfectosBorrado de una muestra grabada BEAT/BANKSíntoma Causa posible Solución Solución DE ProblemasDSP

DJM-400 specifications

The Pioneer DJM-400 mixer is a compact yet powerful addition to any DJ's setup, designed to blend professional capabilities with ease of use. As a two-channel mixer, it provides a perfect balance between features and simplicity, making it ideal for both beginner and experienced DJs.

One of the standout features of the DJM-400 is its high-quality sound output. The mixer is equipped with 48 kHz/24-bit digital signal processing, ensuring crystal-clear audio quality. This level of fidelity is crucial for DJs who want to deliver a party experience that is both immersive and engaging.

The DJM-400 includes a built-in sound card for seamless digital connectivity. This allows DJs to connect to a computer or laptop easily, enabling them to use software like Serato or Traktor. The mixer supports multiple formats and offers USB connectivity, which means it can also be used with a wide variety of devices. Its plug-and-play design minimizes setup time, letting DJs focus on their performance rather than technical issues.

Another noteworthy characteristic is the integrated digital effects processor. The DJM-400 features a range of built-in effects, including delay, echo, and flanger, which can be applied to individual channels, allowing DJs to add depth and dimension to their mixes. The effects can be manipulated using intuitive controls, making it easy to create unique sounds on the fly.

The layout of the DJM-400 has been thoughtfully designed to facilitate quick and easy adjustments. The EQ section features three-band equalizers for each channel, allowing precise control over bass, midrange, and treble frequencies. This empowers DJs to tailor their sound according to the venue and crowd.

Moreover, the DJM-400 comes with a crossfader that is exceptionally smooth, enabling seamless transitions between tracks. The fader is also replaceable, ensuring longevity and catering to individual preferences in performance style.

In summary, the Pioneer DJM-400 is a highly capable mixer that combines excellent sound quality, advanced technology, and user-friendly design. The inclusion of a built-in sound card, a suite of digital effects, and an intuitive layout makes it a versatile choice for DJs of all skill levels. Whether you're just starting your DJ journey or you're a seasoned professional, the DJM-400 delivers the features needed to elevate your performances and connect with your audience.