Bosch Appliances ICP-CC488 manual Delay Alarm Reporting, Silent Alarm, Sensor Watch

ICP-CC488 Installation Guide 14.0 Zone Information

EN 62

The ICP-CC488 Control Panel performs lockout differently than other control panels because only the first zone to activate an alarm is locked out. All other zones that are activated during the same Siren Run Time are reset when the sirens are reset. This prevents an intruder from activating all zones and waiting for the sirens to stop before re-entering the premises.

Example

All zones are programmed for both lockout siren and dialer. Zone 1 is activated, followed by all other zones, which activates the sirens and causes the dialer to report to the base station receiver. Zone 1 is the only zone that stops reporting to the base station receiver because the first activated zone is locked out. The remaining zones continue to report if they are activated again.

Use Location 379 to set the number of times the siren is allowed to activate before it is locked out (refer to Section 14.4 Swinger Shutdown Count for Siren on page 64). Use Location 380 to set the number of times the dialer is activated before lockout takes effect (refer to Section 14.5 Swinger Shutdown Count for Dialer on page 64). ).

2 – Delay Alarm Reporting

Select this option to allow the reporting of alarms on selected zones to be delayed so that a user can enter a code to cancel alarms that are not required to report. All sounding devices (horn speaker, strobe, and bell outputs) operate as soon as the alarm occurs, but the dialer does not operate until the delay time programmed in Locations 474 and 475 expires (refer to Section 17.6 Delay Alarm Reporting Time on page 78).

4 – Silent Alarm

Select this option to program a zone as silent. A silent zone does not activate the horn speaker, bell, strobe, or EDMSAT outputs. The dialer and all other programmable outputs function according to the parameters programmed for the zone.

8 – Sensor Watch

Sensor watch allows the control panel to recognize when detection devices might have stopped working. This feature monitors the operation of a zone over the time period programmed in Locations 476 and 477 (refer to Section 15.5 Zone Status – Sensor Watch Reports on page 78).

This value specifies how many 24-hour periods a zone can remain continuously sealed before it registers as a Sensor Watch fault. The number of hours required to fulfill these 24-hour periods is calculated only when the system is disarmed. Every time the system is armed in the AWAY Mode, STAY Mode 1, or STAY Mode 2, the Sensor Watch Timer pauses its count. The Sensor Watch Timer continues its count the next time the system is disarmed.

Program Locations 389 and 390 to 0 to disable Sensor Watch Reports (refer to Section 15.5 Zone Status – Sensor Watch Reports on page 66).

Example

If the Sensor Watch Time is programmed for 2 days and the premises is armed for 12 hours and disarmed for 12 hours each day, it takes 4 days before a zone can register a Sensor Watch fault.

14.3.6Keyswitch Zone Options

Table 51 on page 62 lists the options available to Keyswitch Zones. If you program a zone as a keyswitch input (Zone Type 11), program the selected Keyswitch Zone options in the location normally used for Zone Options 1. Keyswitch zones report as User Code 16.

Table 51: Keyswitch Zone Options

Option Description

0Latching arm and disarm in AWAY Mode

1Latching arm in AWAY Mode

2Latching disarm from AWAY Mode, STAY Mode 1, or STAY Mode 2

4Latching arm and disarm in STAY Mode 1

5Latching arm in STAY Mode 1

6Latching disarm from STAY Mode 1 or STAY Mode 2

8Momentary arm and disarm in AWAY Mode

9Momentary arm In AWAY Mode

10Momentary disarm from AWAY Mode, STAY Mode 1, or STAY Mode 2

12Momentary arm and disarm in STAY Mode 1

13Momentary arm in STAY Mode 1

14Momentary disarm from STAY Mode 1 or STAY Mode 2

0 – Latching Arm and Disarm in AWAY Mode

The system is armed or disarmed from AWAY Mode when using the latching keyswitch input.

1 – Latching Arm in AWAY Mode

The system is armed in AWAY Mode when using the latching keyswitch input. Disarming the system is not permitted from the Keyswitch Zone.

2 – Latching Disarm from AWAY Mode, STAY Mode 1, or STAY Mode 2

The system is disarmed from AWAY Mode, STAY Mode 1, or STAY Mode 2 when using the latching keyswitch input. Arming the system is not permitted from the Keyswitch Zone.

4 – Latching Arm and Disarm in STAY Mode 1

The system is armed or disarmed in STAY Mode 1 when using the latching keyswitch input. Arming and disarming the system in AWAY Mode is not permitted from the Keyswitch Zone.

Bosch Security Systems, Inc. 12/08 F01U089457-02