| Programmable Outputs |
|
|
EN 70
When programming Test Report options, specify the hour and minute of the day the report is required, and how often to send the report. Test reports are reported on a daily basis from every day to every fifteen days. Refer to Section 5.1.2 Set the Number of Days until the First Test Report to set the first test report.
If Test Reports are not required, program the repeat interval in Location 434 as 0.
Program the Test Report Time as 24:00 to send reports every 30 min.
Example
If you want to send Test Reports once every seven days at 11:35 PM, program Locations 428 to 429 as:
[2 3 3 5 7 1 7]
15.29 Test Reporting Dialer Options
Location 435
0No report allowed
1 Report to Receiver 1
2 Report to Receiver 2
4Report to both Receiver 1 and Receiver 2
8 Report to Receiver 2 only if Receiver 1 fails
Location 435 is set by default to report only to Receiver 1. You can select whether Test Reports are sent to Receiver 1, Receiver 2, or both, Receiver 2 only when Receiver 1 fails, or no reporting.
16.0 Programmable Outputs
The
Programmable outputs require four parameters to operate correctly.
Table 54: | Output Parameters |
|
|
|
|
|
|
|
|
|
|
Parameter | Description |
|
|
Event Type | The Event Type specifies when an output | ||
| is activated. The Output Event Types are | ||
| listed in Section 16.2 on page 71 . Enter | ||
| the code for the Output Event Type into | ||
| the two corresponding locations for the | ||
| output. |
|
|
Polarity | Polarity determines whether the output | ||
| operates for the duration of the event, | ||
| pulses for the duration, operates only | ||
| once (one shot), or latches on. The | ||
| Polarity options are listed in Table 56 on | ||
| page 76. |
|
|
Time Base/ | The Time Base and Time Multiplier | ||
Time | parameters determine how long and how | ||
Multiplier | often the output operates. Refer to | ||
| Section 16.4 Output Timing. |
| |
|
|
|
|
|
|
|
|
Location | 436 to 465 |
|
|
|
| Location | Default |
Output 1 (Default – Horn |
|
| |
Speaker) |
|
|
|
| Event Code | 436 | 1 |
| Event Code | 437 | 14 |
| Polarity | 438 | 0 |
| Time Base | 439 | 0 |
| Time Base Multiplier | 440 | 0 |
| Time Base Multiplier | 441 | 0 |
Output 2 (Default – Fire Alarm With Verification) |
| ||
| Event Code | 442 | 2 |
| Event Code | 443 | 7 |
| Polarity | 444 | 10 |
| Time Base | 445 | 2 |
| Time Base Multiplier | 446 | 1 |
| Time Base Multiplier | 447 | 5 |
Strobe Output (Default – Strobe – Reset After 8 hrs.) | |||
| Event Code | 448 | 2 |
| Event Code | 449 | 0 |
| Polarity | 450 | 6 |
| Time Base | 451 | 4 |
| Time Base Multiplier | 452 | 0 |
| Time Base Multiplier | 453 | 8 |
Relay Output (Default – Sirens Running) |
| ||
| Event Code | 454 | 1 |
| Event Code | 455 | 15 |
| Polarity | 456 | 1 |
| Time Base | 457 | 0 |
| Time Base Multiplier | 458 | 0 |
| Time Base Multiplier | 459 | 0 |
Codepad Buzzer (Default – Entry/Exit Warning and Day | |||
Alarm) |
|
|
|
| Event Code | 460 | 0 |
| Event Code | 461 | 13 |
| Polarity | 462 | 2 |
| Time Base | 463 | 1 |
| Time Base Multiplier | 464 | 0 |
| Time Base Multiplier | 465 | 1 |
|
|
|
|