| System Functions |
|
|
EN 28
Table 27: User Numbers Displayed by the Codepad Indicators
User |
|
|
| Zone Indicators |
|
| ||
Number | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
|
|
|
|
|
|
|
|
|
1X
2 | X |
3 | X |
|
|
4 | X |
|
|
5 | X |
6 | X |
|
|
7 | X |
8 | X |
Example
To delete user code number 3, enter:
[2 5 8 0 1][AWAY][3][AWAY][STAY]
5.2.3Changing and Deleting Remote Radio User Codes
This function allows a Master Code holder to change or delete a remote radio User Code.
To add or change a remote radio User Code:
1.Enter your Master Code and press [1][AWAY]. Three beeps sound and the STAY and AWAY indicators flash.
2.Enter the number of the code (9 to 16) you want to change and press [AWAY].
Two beeps sound and the corresponding codepad indicators light. Refer to Table 28 on page 28.
3.Enter the
4.Repeat this procedure to change other remote radio User Codes.
This function is automatically terminated if you do not press a button within 60 sec or if you press [AWAY].
One long beep indicates that the code already exists or you entered an incorrect user number.
To delete a remote radio User Code:
1.Enter your Master Code and press [1][AWAY]. Three beeps sound and the STAY and AWAY indicators flash.
2.Enter the number of the code (9 to 16) you want to delete and press [AWAY].
Two beeps sound and the corresponding codepad indicators light. Refer to Table 28.
3.Press [STAY] to delete the User Code.
Two beeps sound and the STAY and AWAY indicators are extinguished.
4.Repeat this procedure to delete other remote radio User Codes.
This function terminates automatically if you do not press a button within 60 sec or if you press [AWAY].
One long beep indicates that the code already exists or that you entered an incorrect user number.
Table 28: Remote Radio Numbers Displayed by the Codepad Indicators
User |
|
| Zone Indicators |
|
| MAINS | |||
No | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | Indicator |
9 | X |
|
|
|
|
|
| X |
|
10 |
|
|
|
|
|
|
|
| X |
11 | X |
|
|
|
|
|
|
| X |
|
|
|
|
|
|
|
|
|
|
12 |
| X |
|
|
|
|
|
| X |
13 |
|
| X |
|
|
|
|
| X |
|
|
|
|
|
|
|
|
|
|
14 |
|
|
| X |
|
|
|
| X |
15 |
|
|
|
| X |
|
|
| X |
16 |
|
|
|
|
| X |
|
| X |
5.2.4Changing Domestic Phone Numbers
When the system is set up for domestic dialing, this function allows the installer to view and program the telephone numbers the system calls if an alarm occurs. Refer to Section 9.0 Domestic Dialing on page 42 for more information.
To change domestic phone numbers:
1.Enter you Master Code and press [2][AWAY]. Three beeps sound and the STAY and AWAY indicators flash.
If no telephone numbers are programmed, they are displayed one digit at a time using the remote codepad indicators. Refer to Table 30 on page 29 for the indicators and their meanings.
If no telephone numbers are programmed, an additional two beeps sound after entering this mode. These two beeps normally sound after you enter the last digit of the last phone number.
2.Enter the first phone number.
Each digit is displayed as you enter it.
3.If you are programming another phone number, press [STAY][4] to separate the end of one phone number and the beginning of the next.
If you are not programming other numbers, go to Step 5.
4.Repeat Steps 2 and 3 to program another phone number.
5.Press [AWAY] to exit from this mode.