Time Slots, DS0 Rate | 3Com S24x, S27x, S26x guide

Configuring Channelized Data

Time Slots

Range:	1 to 31

Default:	1

Description:	Each time slot provides a 64k channel to pass traffic. Specify the
	time slot assignment for the logical channel:
	• 1 to 24 for T1 port type
	• 1 to 31 for E1 port type; 16 is not allowed

Boot Type:	Changes to this parameter require a Node boot to take effect.

DS0 Rate

Range:	56k, 64k

Default:	56k

Description:	Specify the DS0 Rate. This sets the rate of speed for each time
	slot.

Boot Type:	Changes to this parameter require a Node boot to take effect.

5-22	Channelized Data

Image 134

3Com S24x, S27x, S26x installation manual Time Slots, DS0 Rate

Contents

3Com Corporation Restricted Rights Notification for U.S. Government Users Restricted Rights Legend Proprietary Material Page Contents Appendix A. Cables Audience OverviewIntroduction Manual About This Manual Trademarks PathBuilder S24x What isSwitch? 26x, Support Meshed ClusterApplication Branch Nodes ApplicationsPerformance Regional Concentrator Regional Concentrator Example PathBuilder S24x, 26x, and 27x Switch Cluster Example Features and Protocols Description PathBuilder S24x, 26x, and 27x Switch Hardware Configuration Hardware Components Component Description HardwareComponents DSPM/SM Ethernet Port 4 Limitations Enclosure Motherboard MotherboardParts Ports Flash Simm Serial/Network Port NumbersSlot Number Port Number Associated Card DIMs without a Cable Adapter DIMs with a Cable Adapter UsedPort Number Use Back Panel Back Panel Components TI Dual Port Digital PBX Interface Card Function Cable Description Function Color LED is Indicating IndicatorsLED Status E1 Dual Port Digital PBX Interface Card PBX Interface Card Illustration DIP SwitchSettings Location RUN Sysfail DSPM/SM Card Step Action 13. DSPM/SM Card 14. Cabling T1/E1 Card to DSPM/SM Cards Dspm Card with Analog E&M Interface 15. DSPM/E&M Card LEDs Settings Setting Jumpers for Dspm Card with Analog E&M InterfaceDefault Jumper Jumper Wire/600 Wire/UK Number Complex Germany 16. UK Complex Impedance 18. Jumper Locations for Dspm E&M Card Dspm Card with FXS Analog Interface 20. Dspm Card with Analog FXS Interface Users Jumper LocationsFor Australian Dspm Host Card with FXO Analog Interface Card Illustration 21. DSPM/HC Card with Analog FXO Daughtercard Hardware Components 48V Ringer/Power Supply Card and Enclosure 22. Standard -48V RInger/Power Supply Card and Enclosure 23. Enhanced -48V RInger/Power Supply Card and Enclosure 10BaseT Transceiver 24 BaseT Transceiver General Radio Frequency Interference RegulationsCanadian DOC Telecommunications Regulations Mise en Garde FCC and Telephone Company Procedures and Requirements FCC Information Electromagnetic RegulationsConcerning Radiation FCC Information Preparation and Unpacking Environment Selecting anOperating Mise en Garde Unpacking Checking PathBuilder S24x, 26x, and 27x Switch Rackmount Kit Placement Considerations PathBuilder S24x, 26x, and 27x Switch Rackmount Kit Step Action Description Step Action Description Removing Pedestal Base Rackmount Assembly Steps for Installing the PathBuilder S24x, 26x, and 27x Switch PathBuilder S24x, 26x, and 27x Switch Hardware Installation Avertissement Switch Settings for Motherboard Switches 1 Setting DIP SwitchesSwitches 1 Set Switch For Installing the DSU DIM DSU DIM Installation Step Action Result/Description Switch Settings INT ConfigurationProcedure EXT Output Signals DSU Input and Output SignalingInput Signals Signal Description IDL CLK Loopback Options If Problems Arise Troubleshooting DSU InstallationTroubleshooting DIM Installing DIMs Example Mise en Garde Installing SIMMs Installing SIMMs BRI Installing I/O CardsInstalling an I/O Installing a T1 or E1 Dual Port Digital PBX Interface Card Installation Place the interface card on an antistatic mat Installing the T1/CSU Daughter Card Follow these steps to install the T1/CSU Daughter card Installing T1/CSU Daughter Cards Cabling the PathBuilder S24x, 26x, and 27x Switch LAN Installing the Transceiver Transceiver Sequence Power-Up Diagnostics/VerificationPower Up Function Description Setting Node to Default NodeCommand Default Installing Software Options Usage ConfiguringFull Mesh Cluster Cabling Cables Mesh Diagram Maintenance Maintenance Removing/Replacing Top Cover Cover Removing the Top Cover Removing/Replacing Front Panel Cover Panel Cover Removing the Front Panel Cover Removing/Replacing Power Supply Supply Removing the Power Supply Removing an Expansion Card Removing the Support Bar Removing an Expansion Card Replacing PathBuilder S24x, 26x, and 27x Switch Motherboard Install Removing the Motherboard Replacing Removing/Replacing the Lithium BatteryBattery Removing the Lithium Battery Removing/Replacing the Lithium Battery Statistics What Is It?Alarms Software Application Example Overview Configuring Channelized Data Configure this Record/Table To do this Configuring Channelized Data Step Action Result Configuring T1 and E1 Physical PortsConfigure Ports 49 or Menu Configure Path Main.6 Node Port Port Record Port Type GuidelinesParameters Port Number Line Framing Type Line Build Out Transmit ClockINT, REC Facility Data Link Threshold Value-PCV Threshold Value LESThreshold Value-LCV Threshold Value-CSS Threshold Value-ES Threshold Value-BES Threshold Value-SES Threshold Value Sefs Threshold Value UAS Line Coding E1 Port RecordParameters Port Type Line Impedance Threshold Value-CSS Threshold Value-SES Threshold Value UAS Enabling/ Disabling Booting VirtualHow to Virtual Ports Port Configuration for Channelized Data Option Configuring Virtual Port Mapping Table What You See Virtual Port Configure Select Virtual Port MappingVirtual Mapping Mapping Table Parameters Virtual Port Number Time Slots DS0 Rate Function/Signal Name EIA 232-D Signals Motherboard and SDBFunction/Signal Pin Pin Function Pin Position Signal Name35/V.36 Motherboard 35/V.36 SDB Function/SignalExternal Transmit Clock B Clock a Test Mode Receive Receive Clock Clock B Data Data Terminal Ready V11 Signals Motherboard Position Signal V11 Signals SDB Ethernet Cable Pinouts Additional Information Ethernet RJ-45S Connector SignalsPin Signal +12V Ethernet Cable Pinouts DC Input Power OutputAC Input PathBuilder S24x, 26x, and 27x Switch Specifications Error Codes Numeric Status Service Description/Comments Display Numeric Status Service Description/Comments Technical Support Access by Digital Modem Access by Analog Modem3ComFacts Automated Fax Service Country Data Rate Telephone Number Country Telephone Number Support from3Com Country Telephone Number Fax Number CTP IndexNumerics DSU FCC Index-3 Simm URL D-1 Disabling Warm Restart World Wide Web WWW D-1 Index-6