3 MRC, MRC2, Affected | ARM VERSION 1.2 manual

ARM Instruction Reference

4.7.3MRC, MRC2

Move to ARM register from coprocessor. Depending on the coprocessor, you might be able to specify various operations in addition.

Syntax

MRC{cond} coproc, opcode1, Rd, CRn, CRm{, opcode2}

MRC2 coproc, opcode1, Rd, CRn, CRm{, opcode2}

where:
cond	is an optional condition code (see Conditional execution on page 4-4).
coproc	is the name of the coprocessor the instruction is for. The standard name
	is pn, where n is an integer in the range 0-15.
opcode1	is a coprocessor-specific opcode.
Rd	is the ARM destination register. If Rd is r15, only the flags field is
	affected.
CRn, CRm	are coprocessor registers.
opcode2	is an optional coprocessor-specific opcode.

Usage

The use of these instructions depends on the coprocessor. See the coprocessor documentation for details.

Note

MRC2 is always unconditional.

Architectures

MRC is available in ARM architecture versions 2 and above.

MRC2 is available in ARM architecture versions 5 and above.

ARM DUI 0068B

Copyright © 2000, 2001 ARM Limited. All rights reserved.

4-65

Image 175

ARM VERSION 1.2 manual 3 MRC, MRC2, Affected

Contents

ARM Developer Suite Assembler Guide ARM Developer SuiteCopyright 2000, 2001 ARM Limited. All rights reserved ARM Developer Suite Assembler Guide Glossary Feedback on About this book on This book is organized into the following chapters Using this bookAbout this book Intended audience ARM publications Typographical conventionsItalic Further reading Other publications ARM Reference Peripheral Specification ARM DDI Feedback on the ARM Developer Suite FeedbackFeedback on this book ARM DUI 0068B About the ARM Developer Suite assemblers on Introduction ARM Developer Suite ADS has About the ARM Developer Suite assemblers Writing ARM and Thumb Assembly Language Code examples IntroductionOr run the module in AXD with interleaving on See ARM processors always start executing code in ARM state Overview of the ARM architectureArchitecture versions ARM and Thumb state Registers Processor modeGeneral-purpose, 32-bit registers Program counter pc Branch instructions ARM instruction set overviewData processing instructions Semaphore instructions Status register access instructionsSingle register load and store instructions Multiple register load and store instructions Following general points apply to ARM instructions Register accessAccess to the inline barrel shifter ARM instruction capabilities Thumb instruction capabilities Thumb instruction set overviewFollowing general points apply to Thumb instructions Differences between Thumb and ARM instruction sets Access to the barrel shifter Single register load and store instructions Case rules Structure of assembly language modulesLayout of assembly language source files General form of source lines in assembly language is Local labels LabelsComments Is a base between 2 Xxx is a number in that base Constants ELF sections and the Area directive An example ARM assembly language module END directive Entry directiveApplication execution Application termination Calling subroutines CODE32 and CODE16 directives An example Thumb assembly language moduleBX instruction Example 2-4 Preprocessing an assembly language source file Using the C preprocessor ALU status flags Conditional execution Examples Execution conditions Example of the use of conditional execution Using conditional execution in ARM state Conditional branches only Branch prediction and caches Converting to Thumb Loading constants into registers Right, 2 bits Direct loading with MOV and MVN Loading with LDR Rd, =const Direct loading with MOV in Thumb state Placing literal pools Loading floating-point constants Direct loading with ADR and Adrl Loading addresses into registers ADR Implementing a jump table with ADR Example 2-7 ARM code jump table Example 2-8 Thumb code jump table Loading addresses with LDR Rd, = label R1, =Darea + = LDR R1,PC, #offset into Literal Pool Address registers. For example, the instruction An LDR Rd, =label example string copyingIncrements r1 by Load register Load and store multiple register instructions Where ARM LDM and STM instructionsSyntax Syntax of the LDM instructions is LDM and STM addressing modes Usage Descending or ascending Implementing stacks with LDM and STM Stacking registers for nested subroutines Example 2-11 Block copy Block copy with LDM and STM Movs Thumb-state block copy example Thumb LDM and STM instructionsLDM and STM Push and POP LSR After substitution this becomes Using macrosTest-and-branch macro example This macro can be invoked as follows If only the remainder is required Unsigned integer division macro exampleRegister that holds the divisor After the instructions are executed, it holds the remainder Ratio DivMod r0,r5,r4,r2 Describing data structures with MAP and Field directives Relative maps Register-based maps Program-relative maps Finding the end of the allocated data Forcing correct alignment EndOfChars Defining register-based symbols Using register-based MAP and Field directives Is equivalent to the C code Setting up a C-type structure If you want the equivalent of the C code Making faster access possible2-27 for an explanation of these Not This example, the MAP directive is Field MAP Using two register-based structures Avoiding problems with MAP and Field directives ArrayBase RN r9 Using frame directives Expressions, literals, and operators on Symbols on Command syntax Position-independent. The default is /norwpi Specifies that the content of inputfile is read-onlyPosition-independent. The default is /noropi Specifies that the content of inputfile is read-write Selects no floating-point option. This makes your assembled Assembled for the wrong target FPUSelection of libraries, accordingly Valid options are Allow unaligned LDRs Command-line optionsSets the maximum source cache size to n. The default is 8MB Object file, for use by the debugger see Keep on Turns off warning messages First pass and reads them from memory on the second passAs \n and \t Register names Assembler Reference Format of source lines Predeclared floating-point register names Predefined register and coprocessor namesPredeclared register names Predeclared program status register names Lists the built-in variables defined by the ARM assembler Built-in variablesExpressions or conditions, for example Determining the armasm version at assembly time Labels on SymbolsSymbol naming rules Numeric constants on Numeric constants Variables Gbls Assembly time substitution of variables Register-relative labels Program-relative labelsDCD and Dcdu on Dcfd and Dcfdu on Dcfs and Dcfsu on DCQ and Dcqu on DCW and Dcwu on Syntax of a reference to a local label is Syntax of a local label is Assembler Reference This section contains the following subsections Expressions, literals, and operators String literals String expressionsString literals Example Numeric expressions Numeric code of the character Is a sequence of characters using only the digits 0 to nNumeric literals Numeric literals can take any of the following forms Floating-point literals can take any of the following forms Floating-point literals There are only two logical literals Register-relative and program-relative expressionsLogical expressions Logical literals String manipulation Operator precedence Operator precedence in C Precedence Operator Usage Description Unary operators Example of use of SBOFFSET1912 and SBOFFSET11 Multiplicative operators Binary operatorsString manipulation operators SHR is a logical shift and does not propagate the sign bit Shift operatorsAddition, subtraction, and logical operators Relational operators 10 shows the Boolean operators Boolean operators ARM DUI 0068B ARM Instruction Reference Add with carry, Add All Logical Branch Move not All ARM condition codes Q flag LDR and STR, doublewords on ARM memory access instructionsLDR and STR, words and unsigned bytes on LDR and STR, halfwords and signed bytes on LDR and STR, words and unsigned bytes Where Is either LDR Load Register or STR Store RegisterOtherwise, a 32-bit word is transferred Post-indexed offset Zero offsetPre-indexed offset Program-relative Flexible offset syntax Loading to r15 Address alignment for word transfers Architectures Saving from r15 LDR and STR, halfwords and signed bytes Is often a numeric constant see examples below Must be within ±255 bytes of the current instructionIs an offset applied to the value in Rn see Offset syntax Offset syntax Incorrect example Offset syntax is the same for LDR and STR, doublewords onAddress alignment for halfword transfers You cannot load halfwords or bytes to r15 Pre-indexed without writeback LDR and STR, doublewordsIs an optional condition code see Conditional execution on Must be an even numbered register, and not r14 Address alignment Not be the same as Rd or Rd+1 Incorrect examples Increment address before each transfer Is either LDM or STMIs any one of the following Increment address after each transfer Loading or storing the base register, with writeback Non word-aligned addresses Is the register on which the memory address is based 5 PLD Alignment 6 SWP Is swapped with the contents of the memory locationBoth Rd and Rm ARM general data processing instructions Flexible second operand Bits of the register are set to LSR and LSL Instruction substitution Carry flag Is the ARM register holding the first operand 2 ADD, SUB, RSB, ADC, SBC, and RSCIs one of ADD, SUB, RSB, ADC, SBC, or RSC Is the ARM register for the result Use of r15 Condition flagsMultiword arithmetic examples These instructions subtract one 96-bit integer from another Logical AND, OR, Exclusive or and Bit Clear 3 AND, ORR, EOR, and BICIs one of AND, ORR, EOR, or BIC Orreq Move and Move Not MOV and MVNIs the ARM register for the result Mvnne Compare and Compare Negative CMP and CMN CMN Test and Test Equivalence TST and TEQ TEQ Is the operand register 7 CLZCount Leading Zeroes Is the ARM register for the result. Rd must not be r15 MUL and MLA on ARM multiply instructionsUMULL, UMLAL, Smull and Smlal on MUL and MLA MUL Is one of UMULL, UMLAL, SMULL, or Smlal UMULL, UMLAL, Smull and Smlal Umull Are the ARM registers holding the values to be multiplied SMULxyUse the top end bits 3116 of Rm Use the top end bits 3116 of Rs Smulbt Is the ARM register holding the value to be added SMLAxy Smlatb Use the top end bits 3116 of Rs SMULWyAre the ARM registers holding the operands Are the ARM registers holding the values to be multiplied SMLAWyIs the ARM register holding the value to be added Smlawt SMLALxy Smlaltt R15 cannot be used for either Rm or Rs 8 MIA, MIAPH, and MIAxyCurrent processors Use the top end bits 3116 of Rm These instructions are only available in XScale Are the ARM registers holding the operands ARM saturating arithmetic instructionsQADD, QSUB, QDADD, and Qdsub Is one of QADD, QSUB, QDADD, or Qdsub Qadd ARM branch instructions Branch, and Branch with Link 2 BX 3 BLX Blxmi MCR, MCR2, Mcrr on ARM coprocessor instructions 1 CDP, CDP2 2 MCR, MCR2, Mcrr Is p n, where n is an integer in the rangeAre ARM source registers. They must not be r15 Affected 3 MRC, MRC2 Mrrc Is the coprocessor register to load or save 5 LDC, STCIs either LDC or STC Is an optional suffix specifying a long transfer Architectures Is either LDC2 or STC2 6 LDC2, STC2 Architectures Miscellaneous ARM instructions Software interrupt 1 SWI Is either Cpsr or Spsr 2 MRSWhere Is the destination register. Rd must not be r15 Is either Cpsr or Spsr 3 MSRSee MRS on MSR CPSRf, r5 Breakpoint Bkpt For current processors 5 MAR, MRAAre general-purpose registers LDR ARM pseudo-instruction on ARM pseudo-instructionsADR ARM pseudo-instructionon Adrl ARM pseudo-instructionon Non word-aligned address within ±255 bytes ADR ARM pseudo-instructionIs an optional condition code Is the register to load Non word-aligned address within 64KB Adrl ARM pseudo-instructionWord-aligned address within 256KB R4,start + = ADD R4,pc,#0xe800 LDR ARM pseudo-instruction R3,=0xff0 Loads Into = MOV r3,#0xff0 NOP ARM pseudo-instruction Thumb Instruction Reference Add with carry Rotate right LDR and STR, pc or sp relative on Thumb memory access instructionsLDR and STR, immediate offset on LDR and STR, register offset on Store register Where Is eitherLDR and STR, immediate offset Load register Address alignment for word and halfword transfers LDR and STR, register offset Strsh 4 in the range 0 to LDR and STR, pc or sp relative R2,pc,#1016 POP reglist These instructions do not affect the flags POP reglist, pc Store multiple, increment after Ldmia and StmiaLoad and store multiple registers Load multiple, increment after R3!, r0,r4 ADC, SBC, and MUL on Thumb arithmetic instructionsADD and SUB, sp on ADD, pc or sp relative on To +7 ADD and SUB, low registers255 to +255 Restrictions These instructions update the N, Z, C, and V flags Is a register containing the second operand 2 ADD, high or low registers Range -508 to +508 ADD and SUB, sp Range 4 ADD, pc or sp relativeIs the destination register. Rd must be in the range r0- r7 Is either sp or pc 5 ADC, SBC, and MUL Where Is one of ADC, SBC, or MUL TST on page 5-30 Test bits Thumb general data processing instructionsCMP and CMN on page 5-26 Compare and Compare Negative MOV, MVN, and NEG on page 5-28 Move, Move NOT, and Negate Range r0- r7 Where Is one of AND, ORR, EOR, or BIC1 AND, ORR, EOR, and BIC Bitwise logical operations 2 ASR, LSL, LSR, and ROR Immediate shift Register-controlled shift Where Is the register containing the first operand Examples Is the source register Where Is the destination register4 MOV, MVN, and NEG Move, Move NOT, and Negate Condition flags Rn and Rm must be in the range r0-r7 Where Is the register containing the first operand5 TST Test bits Thumb branch instructions Label must be within 1 BIs an optional condition code see -2 on 3-23 for more information Condition codes for Thumb B instruction Long branch with Link 2 BL 3 BX BLX label always causes a change to ARM state 4 BLXBranch with Link, and optionally exchange instruction set Instruction clears the T flag in the CPSR. Code at Bkpt on Thumb software interrupt and breakpoint instructions Bkpt immed8 Thumb pseudo-instructions 1KB. expr must be defined locally, it cannot be imported ADR Thumb pseudo-instruction If the value of expr is within range of a MOV instruction, LDR Thumb pseudo-instructionAssembler generates the instruction =labelname Syntax for NOP is NOP Thumb pseudo-instruction ARM DUI 0068B Vector Floating-point Programming Absolute value Vector All Negate Vector All Reference Manual Vector floating-point coprocessorVFP architectures Register banks Floating-point registers Restriction on vector length VectorsVector wrap-around Vector stride Vector operations Vector and scalar operationsControl of scalar, vector and mixed operations Scalar operations VFP and condition codes Vector Floating-point Programming FPSCR, the floating-point status and control register VFP system registers 0b000 See FMRX, FMXR, and Fmstat on FPEXC, the floating-point exception registerFPSID, the floating-point system ID register Modifying individual bits of a VFP system register When to use flush-to-zero mode Flush-to-zero modeEffects of using flush-to-zero mode Operations not affected by flush-to-zero mode Ftosi and Ftoui on VFP instructionsFmrrs and Fmsrr on FMRX, FMXR, and Fmstat onPage Fabsd d3, d5 Fnegsmi s15, s15 Is the VFP register holding the second operand Fadd and FsubIs the VFP register for the result Is the VFP register holding the first operand Fcmp instructions can produce Invalid Operation exceptions FcmpFloating-point compare Fcmp is always scalar With zero instruction Is a double-precision VFP register for the result FcvtdsIs a single-precision VFP register holding the operand Is a single-precision VFP register for the result FcvtsdIs a double-precision VFP register holding the operand Fdiv Address used for the transfer FLD and FSTFloating-point load and store Precision specified in precision Fldsne Fldm and Fstm Following instructions are equivalent Unspecified precision Must be one of FMAC, FNMAC, FMSC, or Fnmsc FMAC, FNMAC, FMSC, and Fnmsc Fnmscsle These instructions do not produce any exceptions Fmdrr and FmrrdIs the VFP double-precision register Are ARM registers. Do not use r15 Is the ARM register. Rd must not be r15 FMDHR, FMDLR, FMRDH, and FmrdlThese instructions are used together as matched pairs Is the VFP single-precision register Fmrs and Fmsr Are two consecutive VFP single-precision registers Fmrrs and FmsrrAre the ARM registers. Do not use r15 Is the ARM register FMRX, FMXR, and Fmstat Fmul and Fnmul Fsito and Fuito Is the VFP register holding the operand Fsqrt Is a single-precision VFP register for the integer result Ftosi and Ftoui Can be S for single-precision, or D for double-precision VFP pseudo-instructionThere is one VFP pseudo-instruction FLD pseudo-instruction D1,=3.12E106 Loads 3.12E106 into d1 Vfpassert Scalar on Vfpassert Vector on VFP directives and vector notation VFP directives and vector notation on Vfpassert Vector on Vfpassert Scalar VFP directives and vector notation on Vfpassert Scalar on Where Is the vector length Is the vector stride R10,FPSCR ARM DUI 0068B Conditional assembly, looping, inclusions, and macros Assembly control directives on Location of descriptions of directives Alphabetical list of directives Declare a global arithmetic, logical, or string variable Symbol definition directivesThis section describes the following directives GBLA, GBLL, and Gbls on GBLA, GBLL, and Gbls Armasm -pd objectsize Seta 0xFF -o objectfile sourcefile LCLA, LCLL, and Lcls SETA, SETL, and Sets Names on Rlist Evaluates to a coprocessor register number from 0 to 5 CNCN directive defines a name for a coprocessor register Coprocessor names on Evaluates to a coprocessor number from 0 to 6 CP DN and SN Evaluates to a floating-point register number from 0 to 8 FN DCD and Dcdu on Data definition directivesDCQ and Dcqu on Ltorg During the first pass of the assembler 2 MAPIs a numeric or program-relative expression Set to this address By the value of expr FieldStorage counter Expressions on Space Consecutive bytes of store 5 DCBTo 255 see Numeric expressions on Quoted string. The characters of the string are loaded into DCW and Dcwu on DCQ and Dcqu on DCD and DcduNumeric expression see Numeric expressions on Program-relative expression Dcdo Dcfd and Dcfdu Dcfs and Dcfsu Is a numeric expression see Numeric expressions on 10 DCI DCD and Dcdu on DCW and Dcwu on DCQ and Dcqu Data DCW and DcwuTo 65535 see Numeric expressions on DCD and Dcdu on DCQ and Dcqu on IF, ELSE, and Endif on While and Wend on Assembly control directivesMacro and Mend on Mexit on Macro and Mend BGE Mexit Using a macro to produce assembly-time diagnostics See Relational operators on 4 IF, ELSE, and Endif Example 7-3 Assembly conditional on a variable being defined While and Wend Frame POP on Frame Push on Frame Register on Frame Restore onFrame description directives Frame Address on Can omit it Is sp unless the function uses a separate frame pointer Is the number of bytes that the stack pointer moves There are two alternative syntaxes for Frame POP There are two alternative syntaxes for Frame Push Frame Push Is the register in which the value is preserved Frame Register Frame Restore Frame Save Frame State Remember Frame State Restore on Function or Proc on Frame State Remember on Function or Proc on Frame State Restore Function or Proc Endfunc or Endp Assert Reporting directivesIs an assertion that can evaluate to either True or False Is an expression that evaluates to a string Info 3 OPT Where Is the OPT directive setting. -2 lists valid settingsSpecify the -listassembler option to turn on listing OPT Is the title TTL and SubtIs the subtitle GET or Include on Miscellaneous directivesCODE16 and CODE32 on Export or Global on Align Cacheable, CODE, ALIGN=3 Area Example,CODE,READONLY An example code section CODE16 and CODE32 4 END Entry directive declares an entry point to a program Entry Is optional. type can be any one Is the symbolic name to assign to the value6 EQU Address, or a 32-bit integer constant Export or Global Exportas Extern Nesting directives on GET or Include Import File, or library. The symbol name is case-sensitiveGlobal See Export or Global on Include IncbinSee GET or Include on Keep Symbols are kept except register-relative symbols Require directive specifies a dependency between sections Assembly failsNofp Require REQUIRE8 and PRESERVE8 Evaluates to a register number from 0 to 19 RN Rout Platforms See ARM Developer SuiteAmong other things, computer software Thumb state Otherwise stated Used to find errors in the application program flowDefault thread runs See also Saved Processor Status Register See Read Write Position Independent See also RopiSee also Rwpi See Read Only Position Independent See Saved Processor Status Register Normally set to zero on resetBlock of software code or data for an Image By ARM to handle semihosting Index Align Gbll Adrl Symbols Index-6