Bosch Appliances 3922 988 43318 manual Control PC requirements, ‘DIRECT’ DCN PC control, PC-card

Digital Congress Network Installation and Operating Manual Chapter 5 - Control using PC en 5-8

EXAMPLE 2: Multi-CCU System with control PC and Camera control

IMPORTANT:The LBB 3510/00 PC Network card CANNOT be used in a PC running Windows NT 4.0 or 2000.

Simultaneous use of the PC-Network card and ‘DIRECT’ connection is NOT possible.

NOTES:

1. When using the ‘DIRECT’ method the

functions of the PC-Network card are NOT

available (i.e. headphones and intercom).

These functions are available on the DCN

Concentus units or with the ‘Multi-purpose

Control PC requirements: Control PC

-Windows 95, 98, NT 4.0 or 2000

-Start-up software LBB 3590.

- DCN software application modules as
required.	COM 1	COM 2
‘DIRECT’ DCN PC control
- Master CCU Port 1	RS232	RS232
- Protocol: FULL
- Baudrate: 115.2k	Male	Male

The COM-port for Master CCU control is selected during software installation. Select COM 1.

By default an ID-chip card encoder is connected to COM 2. COM 2 settings can be changed in the dcn.ini file (see Table 5-11).

e.g. Card encoder or serial printer etc.

connection unit’ LBB 3540/15.

2. The baud-rate setting of the Master CCU

PC port and the corresponding Control PC

port must be the same.The available baud

rate settings are 9600, 19200, 38400, 57600

and 115200. Baud rate setting on the Master

CCU PC must be set in the CCU_CFG file

(SERIAL SPEED I <baud-rate>). For more

information refer to the README.TXT file

of the Multi CCU software LBB 3586. Baud-

rate setting on the DCN Control PC must

be set in the DCN.INI file.This file can be

found in the WINDOWS or WINNT

directory.

[Server]

SerialLink=Yes

				Master CCU PC		Master CCU PC requirements:
Control PC	OS/2 PC			LBB 3511/00		- OS/2 version 3.0 Warp or higher
DCD 1		1	DCD	Multi-CCU		- Multi-CCU software LBB 3586
						- UPS (Uninterrupted Power Supply)
RD 2		2	RD	PC-card
TD 3		3	TD	COM 1	COM 2	recommended
DTR 4		4	DTR
GND 5		5	GND			Video switcher (if applicable)
DSR 6		6	DSR
RTS 7		7	RTS
CTS 8		8	CTS			Power
						ALLEGIANT Video System
RI 9		9	RI	RS232	RS232	Code Out
						Alarm
Female ‘Null modem ’				Male	Male	Battery Low
		Female				Status

9-pole D-type cable connections		See Chapter 6. for installation details
For COM-port settings of the Master CCU PC	75 Ohm Coax cable		LTC 8506/00
(see Chapter 5.7)

[Serial Link]

ComPort=1

Baudrate=<Baudrate>

FullProtocol=Yes

1		LBB 3500/35
Port 1	Mult-CCU			Rec .	Line	Trunk
			In		In
	I n	Out
Port 2			Out		Out	115V -T4A 230V -T2A
					Symmetrical

OUT

To next Multi-CCU

			LBB 3500/35			n (max.16)
Port 1	Mult-CCU			Rec .	Line	Trunk
			In		In
	I n	Out
Port 2			Out		Out	115V -T4A 230V -T2A
					Symmetrical
		IN

From Multi-CCU

FIG 5-7 Multi-CCU System with control PC and Camera control

Bosch Security Systems 04-2003 3922 988 43318 en Connection PC to CCU