Bosch Appliances 3922 988 43318 manual Direct Camera Control, Virtual Keyboard, Camera and Monitor

Digital Congress Network Installation and Operating Manual Chapter 6 - DCN Camera Controlen 6-6

6.2

Direct Camera Control

CCU

AutoDome Camera

With Direct Camera Control (DCC) it is possible to connect one AutoDome camera directly to a

Single CCU

DCD 1

1 GND

A*1AutoDome Camera

CCU. In combination with the relevant software DCC can direct the AutoDome camera towards

RD 2

2 TXD

TD 3

3 RXD

RS232

1

speaking conference participants.The DCC can only be used in combination with:

A

DTR 4

4

+BP

GND 5

5

-BP

•

A BOSCH AutoDome camera

DSR 6

6 SHLD

RTS 7

7

+BP

•

A CCU with TCB 4 or higher

CTS 8

8

-BP

RI 9

• DCN software 9.30 or higher

DCN Control,

Single CCU

or installation PC

9-pole D-type male

terminal block

			B
6.2.1	Virtual Keyboard	RS232	RS232	2
			RS232

A virtual keyboard is used to set the pre-positions of the AutoDome camera.The virtual keyboard		CCU				PC
software LTC 5138/00 must be installed on your temporary PC or DCN control PC.
		DCD 1			1	DCD
		RD 2			2	RD
6.2.2 Camera and Monitor		TD 3			3	TD
	B	DTR 4			4	DTR	installation PC
		GND 5		5		GND
							DCN Control or
One BOSCH AutoDome camera, with RS232 control, can be connected to the CCU. One or more		DSR 6			6	DSR
		RTS 7			7	RTS					3
video displays can be connected to the camera output.These video displays must accept video signals		CTS 8			8	CTS			C
		RI 9			9	RI				AutoDome Camera
according to the PAL-B or NTSC standard as provided by the AutoDome camera.								RS232
	9-pole D-type male		9-pole D-type female

	NOTE: If the distance between camera and CCU or PC is more than 15 meters the RS232
	signal must be converted to Biphase with an LTC 8784/50 converter. (For connection refer to		PC	AutoDome Camera
	FIG 6-4).		DCD 1	1 GND		DCN Control or
			RD 2	2 TXD		installation PC
6.2.3 Installation		C	TD 3	3 RXD		Single CCU			4
			GND 5	5	-BP
			DTR 4	4	+BP		RS232	RS232
FIG 6-4shows the required cables for the following connections:			DSR 6	6 SHLD		RS232			AutoDome Camera
			RTS 7	7 +BP
1. Single CCU to AutoDome camera.			CTS 8	8 -BP		B			C
			RI 9
2.	DCN control or temporary PC to CCU.		9-pole D-type female	terminal block
3. DCN control or temporary PC to AutoDome camera.				Data
			PC	Converter
4.	DCN control or temporary PC to CCU and AutoDome camera (2 COM ports)		DCD 1	1 12 VDC		DCN Control or
5.	DCN control or temporary PC to AutoDome camera via LTC 8784/50 data converter.		RD 2	2 GND		installation PC
			TD 3	3 RX			LTC 8784/50
			DTR 4	4 TX					5
		D	GND 5	5 not used		D	Data Converter
									AutoDome Camera
	CAUTION: To meet EMC requirements all connections made to the ‘Port 1’ output of the		DSR 6	6 12 VDL			RS232
			RTS 7			RS232
	CCU LBB 3500/05(D) or ‘Port 1’ and ‘Poet 2’ of the CCU LBB 3500/15(D) or LBB 3500/35(D)		CTS 8
			RI 9						Biphase
	must be screened cables, where at least one side of the screening is connected to ground.		9-pole D-type female		(Rj-plug)
				Data
			CCU	Converter
			DCD 1	1 12 VDC
			RD 2	2 GND		Single CCU
			TD 3	3 RX
			DTR 4	4 TX			LTC 8784/50		6
		E	GND 5	5 not used		E
									AutoDome Camera
			DSR 6	6 12 VDL			RS232
			RTS 7			RS232
			CTS 8
			RI 9						Biphase
			9-pole D-type male		(Rj-plug)				CL 14155009_001
									191101

FIG 6-4 Connections for DCC

Bosch Security Systems 04-2003 3922 988 43318 en Direct Camera Control