Bosch Appliances 3922 988 43318 manual Set-up Camera configuration, Installation of a Single CCU

Digital Congress Network Installation and Operating Manual Chapter 6 - DCN Camera Control en 6-4

								6.1.4 Set-up Camera configuration
1	CCU	9 pole D-type	Video Switcher		Single CCU to Video Switcher				Reference: To configure and set-up camera positions according to delegate/chairman
	DCD 1			GND
			1					DCN
	RD 2			RD					microphone activity, DACC is available for Stand-alone DCN systems using DCN
			2		Single CCU	*1	Video Switcher	Software
	TD 3		3	TD				Manuals	software package LBB 3562/00 and LBB 3588/00 for PC controlled systems. Refer to
	DTR 4		4	CTS
					RS232		RS232		the relevant software manuals when programming the
	GND 5		5	RTS				BOSCH
	DSR 6			n.c	(female)		(female)		configuration for the DACC system.
			6
	RTS 7		7	GND
	CTS 8		8	n.c				To Install and download the required software modules proceed as follows:
	RI 9		9	n.c

	(Male)		(Male)
2				Connection Installation PC	6.1.4.1 Stand-alone DCN System with Camera Control
	CCU	9 pole D-type	PC	to CCU and Video Switcher

	DCD 1				1	DCD		Temporary Installation PC		For camera installation with stand-alone Camera Control software LBB 3562/00 a temporary PC
	RD 2				2	RD				connection is required.The minimum PC requirements are as follows:
	TD 3				3	TD		COM1	COM2
	DTR 4				4	DTR				• 80486 DX/66 MHz or Pentium processor
	GND 5				5	GND	Single CCU		Video Switcher	• Operating system: Windows 95, Windows 98, Windows 2000, Window NT 4.0
	DSR 6				6	DSR
										• 4MB Random Access Memory (RAM)
	RTS 7				7	RTS
	CTS 8				8	CTS		RS232	RS232	•	Video card: SVGA resolution 640 x 480 pixels, 256 colours
	RI 9				9	RI		(female)	(female)	• Floppy disc drive 3.5 inch, 1.44 MB
	(Male)		(Wire - to - Wire cable)	(Female)						• 100 MB hard disk
3	PC		9 pole D-type	Video Switcher						•	2 Serial ports
										• Monitor or built-in colour LC-display
	DCD 1			1	GND					•	Keyboard and mouse
	RD 2			2	RD
	TD 3			3	TD		OS/2 Master CCU		Video Switcher	6.1.4.2 Installation of a Single CCU
	DTR 4			4	CTS
	GND 5			5	RTS		COM 2			1.	Connect the temporary PC (COM-port 2) to the Allegiant Video switcher (console port).
	DSR	6		6	n.c		PC	RS232	RS232
	RTS 7			7	GND			(male)	(female)	2.	Connect the temporary PC (COM-port 1) to the CCU (Port 2) (see FIG 6-3(2)).
	CTS	8		8	n.c
							Connection OS/2 Master CCU
	RI	9		9	n.c					6.1.4.3 Installation of a Multi-CCU
							to Video Swicher
	(Female)		(Cable LTC 8506/00)		(Male)					1. Connect the temporary PC (COM-port 2) to the Allegiant Video switcher (console port).
4	OS2/CCU		9 pole D-type			PC
							Connection Installation PC			2. Connect the temporary PC CCU (COM-port 1) to the Master CCU (COM-port 2)
							to OS/2 Master CCU and Video Switcher
	DCD 1					DCD					(see FIG 6-3(4)).
					1
	RD 2				2	RD		Temporary Installation PC
	TD 3				3	TD					NOTE: The PC must be installed with the following:
	DTR 4				4	DTR		COM1	COM2
	GND 5				5	GND					1. OS/2 operating system
	DSR 6				6	DSR
	RTS 7				7	RTS	OS/2 Master CCU		Video Switcher		2. Multi-CCU interface card LBB 3511/00
	CTS 8				8	CTS	COM 2				3. Multi-CCU software LBB 3586/00
	RI 9				9	RI	PC	RS232	RS232
			(Null Modem Cable)	(Female)				(male)	(female)
	(Female)									6.1.4.4 4. PC COM Port settings

COM 1 for communication to the CCU (default)

COM 2 for communication to the video switcher

FIG 6-3 RS232 Connections for AVSIf other settings are required they must be specified in the DCNCI.INI file in the Windows directory. The following settings must then be added or changed depending on the selected COM-port:

Bosch Security Systems 04-2003 3922 988 43318 en Allegiant Video Switcher