Cisco Systems ASR 9001, ASR 9001-S Installing an AC or DC Power Module

5-7

Cisco ASR 9001 and Cisco ASR 9001-S Routers Hardware Installation Guide

Chapter5 Replacing Cisco ASR 9001 Router Components

Removing and Replacing AC or DC Power System Components

Figure5-3 Removing or Installing an AC or DC Power Module (AC power shown)

Installing an AC or DC Power Module

To install an AC or DC power module (Figure5-3):

Step1 Slide the power module into the open bay until it mates with its backplane connector. Make sure that

keying lever locks with the chassis.

Step2 Attach the power cabling to the power module.

Step3 Verify that the OK (green) power indicator on the front of the power module comes ON. If the indicator

does not light up, see Troubleshooting the Power Subsystem, page4-3.

332383

Contents

Main Page CONTENTS Page Page Page Page Page Preface Changes to This Document Audience Purpose Document Organization Document Conventions Obtaining Documentation and Submitting a Service Request Page Preparing for Installation Safety Guidelines General Safety Guidelines Compliance and Safety Information Laser Safety Energy Hazard Preventing Electrostatic Discharge Damage Lifting Guidelines Site Requirement Guidelines Site Layout and Equipment Dimensions Rear of chassis Front of chassis Site Wiring Guidelines Chassis Air Flow Guidelines Room air Air exhaust Rack-Mounting and Air Flow Clearance Guidelines Telco 2-Post Rack Open 4-Post Rack Enclosed Rack with Perforated Sides Air Flow Guidelines for Enclosed Rack Installation Temperature and Humidity Guidelines Power Connection Guidelines AC Powered Routers AC Power Cord Illustrations 1-14 Figure1-9 AC Power Cord CAB-AC Figure1-10 AC Power Cord CAB-L620P-C13-JPN Figure1-11 AC Power Cord CAB-ACA 1-15 Figure1-12 AC Power Cord CAB-ACI Figure1-13 AC Power Cord CAB-ACR Figure1-14 AC Power Cord CAB-ACS 1-16 DC Powered Router Page Page NEBS Supplemental Unit Bonding and Grounding Guidelines Cisco ASR 9001 Router Port Connection Guidelines 1 3 4 5 6 687 92 Console Port and Auxiliary Port Connection Guidelines Console Port Signals Auxiliary Port Signals Management LAN Ports Connection Guidelines Management LAN Port LED Indicators Management LAN RJ-45 Cabling Sync Ports Connection Guidelines SYNC Port LED Indicators RP External USB Port Page Unpacking and Installing the Chassis Pre-Installation Considerations and Requirements Unpacking the Cisco ASR 9001 Router Positioning the Router Installing the Cisco ASR 9001 Chassis Before you Begin Rack-Mounting the Chassis Verifying Rack Dimensions Installing the Chassis in a Two-Post Rack Page Installing the Chassis in a Four-Post Rack Supplemental Bonding and Grounding Connections Installing the Optional Air Plenum Kit Air Plenum Kit Contents Supported Rack Types and Adapter Plates Installing the Air Plenum Kit Installing the Air Plenum Kit in a 19-inch Rack Page Page Page Page Installing the Air Plenum Kit in an ETSI Two-Post to Four-Post Rack Page Page Page Page Page Page Installing Modules and Cables in the Chassis Fixed 4x10-Gigabit Ethernet Ports Modular Port Adapters 92 20-Port Gigabit Ethernet Modular Port Adapter 1 3 4 5 6 687 4-Port 10 Gigabit Ethernet Modular Port Adapter 2-Port 10 Gigabit Ethernet Modular Port Adapter 2-Port 40 Gigabit Ethernet Modular Port Adapter Page 1-Port 40 Gigabit Ethernet Modular Port Adapter Installing and Removing Modular Port Adapters Handling Modular Port Adapters (MPAs) Online Insertion and Removal Modular Port Adapter (MPA) Installation and Removal Optical Device Installation and Removal Cleaning Optical Devices Checking the Installation Verifying the Installation Using show Commands to Verify Modular Port Adapter (MPA) Status Using show Commands to Display Modular Port Adapter (MPA) Information Using the ping Command to Verify Network Connectivity Installing and Removing SFP and XFP Modules Cable Management Cable Management Tray Installing a Cable Management Tray Removing a Cable-Management Tray Cable Management Bracket Installing a Cable Management Bracket Removing a Cable-Management Bracket Connecting Route Processor Cables Connecting to the RP Console Port Connecting to the RP Auxiliary Port Connecting to the RP Ethernet Management Ports Connecting Power to the Router Connecting Power to an AC-Powered Router Page Connecting Power to a DC-Powered Router Powering on the Router Page Troubleshooting the Installation Troubleshooting Overview Troubleshooting Using a Subsystem Approach Normal Router Startup Sequence Identifying Startup Issues Troubleshooting the Power Subsystem Troubleshooting the AC-Input Power Subsystem Page Troubleshooting the DC-Input Power Subsystem Troubleshooting a DC Power Module Additional Power Subsystem Troubleshooting Information Hardware and Software Identification Obtaining Temperature and Environmental Information 4-7 Troubleshooting the Power Distribution System Troubleshooting the Route Processor Subsystem Route Processor Overview 92 1 3 4 5 6 687 RP Front Panel Indicators FAIL /OK (Power Module) Ethernet Ports and Status LEDs Auxiliary and Console Ports STATUS (Fan tray) Monitoring Critical, Major, and Minor Alarm Status Troubleshooting the Line Card Initial Boot Process Status LEDs Configuring and Troubleshooting Line Card Interfaces Configuration Parameters Line Card Interface Address Using Configuration Commands Basic Line Card Configuration Verifying the Transceiver Modules 4-16 Advanced Line Card Troubleshooting Troubleshooting the Cooling Subsystem Fan Tray Operation Power Module Fans Over-temperature Conditions Isolating Cooling Subsystem Problems Page Replacing Cisco ASR 9001 Router Components Prerequisites and Preparation Field Replaceable Units Online Insertion and Removal Powering Off the Router Removing and Replacing the Fan Tray Removing and Replacing a Fan Tray Removing and Replacing the Air Filter Page Removing and Replacing AC or DC Power System Components Power Module Replacement Guidelines Removing and Replacing an AC or DC Power Module Removing an AC or DC Power Module Installing an AC or DC Power Module Removing a Chassis from the Equipment Rack Installing a Replacement Chassis in the Equipment Rack Packing a Chassis for Shipment APPENDIX A Technical Specifications Physical Specifications Environmental Specifications AC Electrical Specifications DC Electrical Specifications AC Input Voltage Range DC Input Voltage Range Power System DC Output Levels RP Port Specifications. Power Consumption Specifications Fast Ethernet and Gigabit Ethernet SFP Modules 10-Gigabit Ethernet SFP+ Transceiver Modules SFP+ Transceiver Modules DWDM SFP+ Transceiver Modules DWDM XFP Transceiver Modules CWDM SFP Transceiver Modules 10GBASE CWDM SFP+ 40km Transceiver Modules DWDM SFP Transceiver Modules DWDM SFP+ Transceiver Modules Page 10-Gigabit Ethernet XFP and 40-Gigabit QSFP Modules DWDM XFP Transceiver Modules Page Page APPENDIX B Site Log